Dishwasher Loose Band Wire Connection Parts

The Pump to Heater Hose Clamp is an OEM part for Bosch dishwashers. This clamp secures the hose that connects the pump to the heater, ensuring a tight and leak-free connection. It plays a crucial role in maintaining the integrity of the water flow within the dishwasher, preventing leaks and ensuring efficient operation.

Causes of a bad hose clamp can include wear and tear over time, loosening due to vibrations, or damage from repeated tightening and loosening. A faulty clamp can lead to water leaks, which can cause further damage to the dishwasher.

Symptoms of a bad pump to heater hose clamp include:

• Water leaking from the hose connection points
• Reduced water pressure within the dishwasher
• Visible wear, rust, or damage on the clamp
• The clamp not holding the hose securely in place

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Power Cord is an OEM replacement part for Bosch dishwashers. It supplies electrical current that allows the dishwasher to properly perform cycles. Located at the rear of the appliance, it plugs into a standard three-prong outlet.

Causes for power cord replacement include cracking, splitting, or breaks in the protective insulation over time from repeated bending and stress.

Symptoms of a faulty power cord include:

• Unresponsive or failed cycles indicating no power to operate
• Melted, blackened, or charred areas along the cord housing
• Visible frayed wires or exposed copper filaments

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Power Cord is an OEM part for Whirlpool stand mixers. It provides the electrical connection between the mixer and the power source, allowing the appliance to function properly.

A bad power cord can be caused by wear and tear, accidental damage, or electrical issues. If you experience problems such as intermittent power supply, sparks or frayed wires, or the mixer not turning on at all, it may indicate a problem with the power cord.

Symptoms of a bad power cord include:

• Intermittent power supply or loss of power during operation
• Sparks, exposed wires, or fraying along the cord
• Inability to turn on the mixer  

Replace your faulty power cord with this genuine OEM part to restore your stand mixer. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This replacement power cord supplies electrical power from the household outlet to the appliance. Swap a frayed, heat-damaged, or loose cord to restore safe, reliable operation and prevent intermittent power loss.

• Delivers AC power from the outlet to the unit
• Common symptoms include no power, intermittent shutoff, tripped breaker/GFCI, burning odor, or visible cuts/fraying
• Replaces cords with cracked insulation, loose/bent blades, or heat discoloration
• Helps maintain proper grounding when installed as originally routed

• Disconnect power and verify the outlet is de-energized before servicing
• Photograph wire routing; transfer connections one at a time to match the original
• Install/secure the strain relief; route the cord away from sharp, hot, or moving parts
• Test for normal operation after reassembly

The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.

Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.

Symptoms of a bad power cord include:

• The dishwasher not turning on or completing cycles
• Warm or hot power cords during operation
• Frayed, cracked, or exposed copper wiring

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

The Power Cord is an OEM part for Whirlpool mixers. It provides the necessary electrical connection between your mixer and the power source, enabling your mixer to run reliably and safely.

Symptoms of a faulty power cord include:

• Intermittent power loss
• Exposed or frayed wires
• Loose connection or difficulty in maintaining power

A bad power cord can occur due to wear and tear, accidental damage, or electrical issues. If you experience problems such as intermittent power loss, exposed wires, or a loose connection, it may be time to replace the power cord.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This line cord supplies electrical power from the wall outlet to the appliance. Replacing a worn, cut, or heat-damaged cord restores safe, reliable power and can help resolve no-power or intermittent operation issues.

• Delivers AC power from the outlet to the unit's electrical system
• Helps correct no-power or intermittent power when the cord is moved
• Ideal replacement for cords with cuts, fraying, or burn/discoloration on the plug
• Supports proper grounding and safe operation when installed correctly

• Disconnect power before servicing; ensure the appliance is fully de-energized
• Match wire routing and connections to the product's wiring diagram; ensure a secure ground
• Use an appropriate strain relief if required by the product to prevent abrasion
• Route the cord away from sharp edges, moving parts, and hot surfaces

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

This dishwasher hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal during operation. Replacing a worn or corroded clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place.

• Secures dishwasher hoses to fittings on pumps, valves, or drain outlets
• Helps prevent water leaks at hose connections
• Keeps hoses from slipping off under vibration and water pressure
• Typical symptoms include water under the unit, dampness in the cabinet, or a hose connection that feels loose

• Disconnect power and shut off water supply before servicing
• Access the hose connection (toe-kick or rear/side panels may need removal)
• Seat the hose fully on the fitting, position clamp just behind the barb/ridge, and secure without over-tightening
• Run a short test cycle and check all connections for leaks

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

This sump clamp secures the dishwasher sump to the tub assembly, keeping the gasket compressed for a watertight seal. Replacing a weakened or corroded clamp helps stop leaks from the base and restores proper wash system sealing.

• Holds the sump firmly to maintain seal compression
• Helps prevent water leaking from the bottom of the dishwasher during operation
• Replace when the existing clamp is rusted, broken, stripped, or won't tighten

• Disconnect power at the breaker and shut off the water supply
• Remove the toe kick and, if needed, pull the dishwasher forward for access
• Position the clamp over the sump-to-tub joint and tighten evenly; do not overtighten
• Reseat the sump gasket and run a leak test after reassembly

This dishwasher power cord connects your appliance to a standard household outlet. Replace a frayed, damaged, or missing cord to restore a safe, reliable power connection and help prevent intermittent power issues.

• Supplies power from a wall outlet to the dishwasher's electrical connection
• Appropriate when the existing cord shows cuts, fraying, burn marks, or melted insulation
• Supports safe restoration of the factory-style corded installation when specified for your model

• Disconnect power at the breaker before servicing.
• Route through an approved strain relief; connect hot, neutral, and ground to the marked terminals/junction as instructed by the manufacturer.
• Ensure wiring is secured and not pinched; test operation before sliding the unit fully back into place.

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

This dishwasher hose clamp secures a hose to its fitting to help prevent leaks. Replace a corroded or loose clamp to restore a tight, reliable seal at a hose connection point. What it does:

• Tightens around a dishwasher hose and fitting to maintain a watertight seal
• Helps resolve leaks at hose joints or beneath the unit
• Replaces clamps that are corroded, bent, stripped, or won't hold tension
• Symptoms include moisture at the connection, hose slipping off, or recurring leaks

• Includes 1 hose clamp

• Disconnect power at the breaker and shut off the water supply before servicing
• Access the affected hose connection and place a towel or pan to catch residual water
• Release and remove the old clamp; fully seat the hose, position the new clamp just behind the fitting's barb, and tighten/secure
• Run a short cycle and check for leaks at the connection

This sump clamp secures the dishwasher's sump connection at the base of the tub, helping maintain a tight, leak-resistant seal. Replacing a weakened or corroded clamp can help stop drips and keep the wash system stable.

• Secures the sump connection so it stays firmly in place
• Applies even clamping force to help maintain a watertight seal
• Helps prevent leaks or puddles beneath the dishwasher
• Typical signs include water leaking from the bottom, a loose connection, or a rusted/broken clamp

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick and access the sump area; have towels or a pan ready for residual water
• Loosen and remove the old clamp; inspect mating surfaces and the sump seal/gasket and replace if worn
• Position the new clamp squarely and tighten evenly—do not overtighten; run a brief test and check for leaks

Includes 12 retainers.