Dryer Basket Silverware Arm Parts

This replacement idler pulley keeps the drive belt tight and tracking correctly so the drum can rotate smoothly. It restores quiet, consistent operation when the original pulley is worn or seized and causing belt slippage or noise.

• Maintains proper tension on the drive belt to enable smooth drum rotation
• Provides a low-friction surface for the belt to ride on and stay aligned
• Common symptoms of failure: squealing/chirping, belt fraying or coming off, burning rubber smell, or a drum that won't turn
• Replace if the pulley wobbles, binds, or the rim/bearing is worn

• Disconnect power; if gas, shut off the gas supply
• Note belt routing, relieve tension from the idler arm, and remove the belt from the motor pulley
• Remove the retaining hardware from the old pulley, install the new pulley on the idler arm shaft, and re-tension the belt
• Manually rotate the drum to verify smooth belt tracking before reassembly and test run

This dryer drum support roller holds the drum on its axle and lets it rotate smoothly. Replacing a worn or noisy roller restores quiet, even tumbling and helps prevent belt strain and added wear on related parts.

• Supports the dryer drum and allows low-friction rotation on the shaft
• Helps keep the drum aligned and stable during cycles
• Wear can cause squeaking, thumping, rumbling, or grinding noises
• Flat spots, cracks, or excessive wobble indicate replacement

• Disconnect power; turn off gas supply for gas models
• Access the roller by removing the front or rear panel/bulkhead per model; relieve belt tension and support the drum
• Install the new roller on the existing shaft, reusing model-specific washers/clips as required
• Inspect remaining rollers, idler pulley, and belt; replace any worn parts together to maintain smooth, quiet operation

This replacement pulley guides the drive belt so the drum or tub turns smoothly and reliably. A worn pulley can squeal, shred belts, or stop the load from tumbling or spinning.

• Guides the drive belt and helps transfer motor power to the drum/tub
• A seized or damaged pulley can cause the drum/tub not to turn or to stall
• Inspect for cracks, wobble, or rough bearings during diagnosis

• Disconnect power before servicing; if working on a gas dryer, also shut off the gas supply. For washers, turn off water.
• Access the belt path; release belt tension and remove the old pulley.
• Install the new pulley and route the belt correctly; rotate by hand to confirm smooth tracking.
• Inspect and replace a worn drive belt or related belt-drive components while open.

Dryers, washers, and washer dryer combos are made with an idler pulley shaft. It works in combination with the rest of the equipment in multiple ways. It switches the direction in which the output shaft is rotating. The idler pulley shaft also works to change gears and maintain the space between shafts. With time, because of excessive force, or as a result of misuse, the idler pulley shaft can wear out, break, or get damaged otherwise. When the part isn't working correctly, it has to be replaced to continue using the machine.The primary indication that there is something wrong with the idler pulley shaft is a machine that's producing excessive noises. Replacement of the idler pulley shaft is a straightforward process. It can be done in a few minutes with a nut driver and screwdrivers. Unplug the appliance before starting the disassembly.This idler pulley shaft is a genuine OEM replacement part. It is sold as an individual unit. It is made of durable metal materials. The idler pulley shaft is sourced from the manufacturer. It can be installed in various machines made by Speed Queen, Amana, and Magic Chef.

This Dryer Grid Assembly is an OEM part for GE dryers. The grid assembly helps to filter out lint and debris from the air exiting the dryer, ensuring efficient operation and reducing the risk of overheating or fire hazards. 

The need for replacement of the dryer grid assembly can be due to accumulation of lint, physical damage, or general wear over time. A malfunctioning or clogged grid assembly can affect the dryer's performance and safety.

Symptoms of a bad Dryer Grid Assembly include:

• Excessive accumulation of lint beyond the lint trap.
• Reduced drying efficiency, leading to longer drying times.
• Unusual amounts of heat coming from the dryer.
• Potential risk of overheating or fire hazards.
• Visible damage or wear to the grid assembly.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This idler pulley shaft serves as the axle the idler pulley rides on, helping maintain proper belt alignment and tension. Replacing a worn shaft can reduce squealing, wobble, and belt wear so the drive system runs smoothly. What it does:

• Acts as the pivot/axle for the idler pulley within the belt-tensioner assembly
• Helps keep the drive belt aligned and properly tensioned
• Wear or scoring can cause pulley wobble, squeaking/squealing, or belt fraying
• Can contribute to belt slippage and intermittent loss of drive

• One idler pulley shaft

• Disconnect power; shut off gas or water supply if applicable
• Relieve belt tension and access the idler assembly
• Note and transfer any spacers, washers, or retainers from the old shaft to the new one
• After reassembly, the pulley spins freely on the shaft and the belt tracks correctly

Replacement roller that helps a dishwasher rack glide smoothly along its track, restoring proper rack alignment and quieter operation. Fits where a worn or damaged wheel causes the rack to stick, wobble, or derail. What it does:

• Replaces a worn or broken rack wheel so the rack rolls smoothly on its track.
• Stops rubbing, grinding noise, and uneven movement caused by a damaged roller.
• Prevents the rack from coming off the track or tilting when loaded.
• Helps restore proper rack alignment for easier loading and unloading.

• Disconnect power and water to the appliance before starting work.
• Inspect the rack track and mounting clip; replace clips or retainers if damaged.
• Typically installs with basic hand tools (screwdriver/pliers) — match orientation to the original wheel.
• Test rack travel after installation to ensure proper seating and smooth operation.

This front bulkhead assembly forms the dryer's front drum support and air seal. Replacing a worn or damaged bulkhead restores smooth drum rotation, reduces noise, and helps maintain proper airflow for consistent drying performance.

• Supports and aligns the drum at the front to prevent rubbing and scraping
• Helps seal the lint/air path so heat stays in the drum and exhaust flows correctly
• Air leaks at the front bulkhead can contribute to long dry times or lint in the cabinet

• Disconnect power and gas supply and allow the dryer to cool before servicing
• Remove the front panel/door assembly; support the drum before detaching the old bulkhead
• Transfer any model-specific components from the original bulkhead and ensure seals/glides are correctly positioned
• After installation, rotate the drum by hand to verify clearances, then reassemble and test

This bulkhead is the front tub housing that supports the washer drum and seals the washer cabinet to help contain water. Replaces a cracked or corroded housing to restore proper drum alignment and help prevent leaks. What it does:

• Provides structural support for the washer tub and drum assembly
• Forms the front seal surface to help keep water inside the washer
• Helps maintain correct drum alignment to reduce noise and wobble
• A failing bulkhead can cause visible leaks, excessive vibration, or rubbing noises

• Disconnect power and water supply before starting any repair
• Inspect surrounding seals, gaskets, and mounting hardware when replacing the bulkhead
• Replacement may require partial disassembly of the washer cabinet and drum; follow OEM instructions

This drum wheel supports the dryer drum and helps it spin smoothly so clothes tumble evenly. Replacing a worn wheel restores stable drum rotation and reduces rubbing noises or scraping. What it does:

• Supports the drum at the rear/front and allows it to roll on the axle or shaft.
• Reduces friction and prevents metal-on-metal contact that can cause squealing or grinding.
• Helps keep the drum aligned to avoid uneven wear and noisy operation.
• Common symptom fix: noisy or hard-to-turn drum, scraping or wobbling during rotation.

• Disconnect power (and shut off gas for gas dryers) before starting any repair.
• Support the drum while removing panels and the belt to avoid dropping or bending the drum.
• Inspect other rollers, bearings, and the belt for wear while replacing the wheel; replace any worn parts to prevent repeat failure.

This roller support holds the dryer drum roller in place to help the drum turn smoothly and stay aligned. Replacing a worn support can reduce noise and wobble and help protect the belt and drum from uneven wear. What it does:

• Holds and positions the drum roller so the drum rotates with minimal friction
• Keeps drum alignment and belt tracking stable during operation
• Helps prevent drum wobble and uneven wear that can lead to rubbing or thumping noises
• Common symptoms: loud squealing or grinding, thumping during rotation, visible drum wobble

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the dryer front or rear panel; follow the model's service manual
• Inspect the roller, axle, and adjacent support components; replace any worn parts to prevent repeat failure
• Use proper tools and secure fasteners to factory torque

Replacement dryer drum that holds and tumbles laundry so air circulates evenly for efficient drying. Restores a smooth rotating drum surface to prevent fabric damage and improve drying performance. What it does:

• Houses and tumbles clothes while allowing heated air to pass through the load.
• Replaces a dented, cracked or scored drum that can catch or abrade fabric.
• Stops metal-on-metal scraping or grinding noises caused by a damaged drum surface.
• Helps eliminate uneven drying caused by a misshapen or warped drum.

• One replacement drum.

• Disconnect power (and gas supply for gas models) before starting any repair.
• Drum removal usually requires loosening the front panel and supporting the drum; consider a second person—the drum is heavy and awkward.
• Inspect and replace related components if worn to prevent repeat failures.
• Test-run the dryer after installation to ensure smooth rotation and proper clearance.

This drum support roller cushions and guides the dryer drum so it turns smoothly and quietly. Replacing a worn roller restores stable drum rotation and reduces noise, vibration, and uneven tumbling. What it does:

• Supports the dryer drum to keep it aligned during rotation
• Reduces scraping, squeaking, or grinding noises caused by worn rollers
• Prevents excessive drum wobble that can lead to belt wear
• Helps maintain even tumbling for consistent drying

• One drum support roller

• Disconnect power (and gas supply for gas dryers) before starting any repair
• Access usually requires removing the dryer back panel or cabinet—use basic hand tools
• Inspect drum glides, idler pulley, and belt while the dryer is open; replace other worn parts as needed

This bulkhead is the structural panel that supports and seals the washer tub and provides mounting points for related components. It restores proper alignment and containment so the washer can hold and drain water correctly. What it does:

• Provides a secure mounting surface for the tub, seals, and associated fittings
• Helps route and contain water inside the washer cabinet to prevent leaks
• Maintains correct alignment for the tub and connected components
• Commonly replaced when leaks, cracks, or warped mounting surfaces cause water loss or misalignment

• One bulkhead panel

• Turn off power and water supply before beginning any repair
• Handle gently to avoid damaging mating surfaces or embedded seals
• Verify matching orientation and fastener locations to the original part
• If seals or gaskets are attached separately on your model, replace them as needed

This motor drive pulley transfers power from the dryer motor to the drum belt so the drum spins smoothly. Replacing a worn pulley restores proper belt tracking and reduces noise for reliable drying performance. What it does:

• Guides and supports the drive belt so the drum turns freely
• Maintains correct belt alignment to prevent slipping or fraying
• Replaces noisy, cracked, or worn pulley surfaces that cause squealing
• Helps restore normal drum rotation when the belt skips or the drum won't turn

• Disconnect power before servicing to avoid injury
• Inspect the drive belt and idler for wear; replace if damaged
• Use basic hand tools; support the drum and follow the dryer's service manual

The Tension Roller is an OEM part for Bosch dryers. This part maintains the correct tension on the drive belt to ensure smooth and efficient operation. The tension roller ensures that the belt is tightly secured around the drum, allowing it to rotate smoothly and evenly during cycles.

The need for replacement can stem from normal wear and tear over time, as the roller can become worn or damaged, affecting its ability to maintain proper tension on the belt. 

Symptoms of a failing Tension Roller include:

• Unusual noises, such as squeaking or grinding, coming from the dryer when it is running. 
• The dryer drum not spinning correctly or at all, which can occur if the tension roller is not providing the necessary support and tension for the belt.
• Excessive vibration during operation, suggesting that the drive belt is not tensioned properly

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.