Washer Latch Switch Parts

This water level pressure switch senses the tub's water level via air pressure and signals the control to stop filling at the correct point, helping the cycle advance properly and guarding against overfilling.

• Monitors water level through the pressure hose and reports to the control
• Shuts off inlet valves when the target level is reached
• Allows the cycle to proceed and spin only when the tub is sensed empty
• Common symptoms of a failed switch include overfilling or underfilling, long fill, stopping during fill, not advancing, or water-level error codes

• Disconnect power and turn off water supplies before servicing
• Access the console/control area; move the wire harness and pressure hose to the new switch and secure it in place
• Inspect the pressure hose for kinks, cracks, or moisture; clear or replace if damaged to ensure accurate sensing
• Ensure an airtight hose connection, then run a test fill to verify proper shutoff and operation

This rotary on/off switch controls the dryer's Finish Guard (also called Wrinkle Guard/Wrinkle Shield) feature. Replacing it restores proper control of the post-cycle intermittent tumbling that helps reduce wrinkles, preventing the feature from being stuck on or off.

• Provides 2-position on/off selection for the Finish Guard/Wrinkle Guard function
• Failure can cause the feature not to engage or to stay on after the cycle ends
• Knob may feel loose or fail to click when the switch is worn
• Mounts in the control console and interfaces with the external selector knob

• Disconnect power before servicing
• Access through the control console; remove paneling as needed
• Transfer wires one at a time or photograph connections for reference
• Reinstall using the existing knob and mounting hardware

A small rubber bumper that cushions and protects appliance doors, drawers or panels to reduce noise and prevent hard contact. Replaces worn or missing bumpers to restore a snug, quiet close. What it does:

• Provides a soft buffer to stop doors or drawers from banging into the cabinet or frame
• Reduces vibration and rattling during operation
• Helps doors and panels sit properly when closed
• Simple, non-electrical part — no wiring or adjustment required

• One replacement bumper

• Inspect the mounting hole or surface; clean debris before installing
• Press the bumper into the hole or onto the surface until fully seated; use a blunt tool if needed for tight fits
• Disconnect power to the appliance first and follow OEM instructions
• Remove old adhesive before installing the new bumper

This replacement switch assembly restores the appliance's electrical switching function so the control or safety circuit can open and close when activated. Use it to replace a worn or failed switch and regain expected control response. What it does:

• Acts as the electrical contact that opens or closes a circuit when toggled or pressed
• Commonly used where a user action or door/lid position must be sensed by the control
• Can address symptoms such as no start, unresponsive controls, or intermittent operation tied to the switch circuit
• Transfers the mechanical action to the appliance's control or safety system

What's included: One switch assembly Install notes:

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Verify correct wiring and connector orientation before reassembly; take photos if needed
• Test switch continuity (with power off) after installation to confirm correct operation

This door catch assembly secures the door closed so your machine can start and run without interruptions. A worn or broken catch can keep the door from latching, causing cycles not to begin or to stop mid-cycle.

• Latches the door to engage the door switch and allow operation
• Helps prevent door popping open during use
• Common failure signs: door won't stay closed, must hold door to run, cycle won't start due to open-door indication
• Restores proper door alignment and engagement with the strike

• Unplug the appliance before servicing
• Open the door and remove the fasteners securing the old catch
• Transfer the new catch in the same orientation; reuse existing screws if not supplied
• Test door closure and latch engagement before resuming use

This replacement key restores operation of a factory-installed lock on select appliances, letting you securely lock or unlock a door, lid, or compartment when the original key is lost or damaged. What it does:

• Operates the keyed lock cylinder to lock and unlock the appliance compartment
• Restores access when the original key is missing, bent, or broken
• Helps keep contents secure by re-enabling the lock function

• Insert fully and turn gently—do not force the cylinder
• If the lock is stiff, clean the keyway; use only manufacturer-approved lubricants if needed
• Disconnect power before any related service; keep the key out of children's reach

This 3-position temperature switch selects the dryer's heat level so the appliance reaches the desired drying temperature. It replaces a worn or faulty selector to restore proper temperature selection and consistent drying performance. What it does:

• Switches between three temperature settings to control dryer heat levels.
• Routes power to the heater circuit based on the selected heat setting.
• Commonly replaces a switch that causes incorrect heat, no heat on some settings, or inability to change temperature.
• Works with the dryer's control system and thermostats to maintain selected drying temperature.

• Disconnect power to the appliance before attempting any service.
• Handle terminals and connectors carefully; match wiring to original locations or take a photo before removal.
• Verify operation with a multimeter for continuity per service manual before and after installation.

The Lid Switch is an OEM part for Frigidaire washing machines. It is an electronic component located within the washer lid that functions to detect when the lid is opened or closed. The lid switch communicates this information to the control unit to allow or pause the operation of the washer accordingly.

Causes of a bad lid switch can include wear and tear of sensitive electrical contacts over time, exposure to moisture or debris that disrupts connections, or accidental physical damage to the switch mechanism.

Symptoms of a bad lid switch include:

• The washer fails to start or run when the lid is closed   
• Inability to pause the cycle when the lid is opened
• Fault codes or error messages related to lid position detection

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This lid switch assembly detects when the washer lid is closed and lets the machine start and complete cycles. Replacing a failed switch restores the washer's safety interlock and helps resolve start/spin problems. What it does:

• Detects lid closure to enable motor and spin cycles
• Prevents the washer from starting or spinning when the lid is open
• Common replacement for washers that won't start, won't spin, or stop mid-cycle
• Completes the electrical safety/interlock circuit for proper operation

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access may require removing the top or rear access panel; keep track of fasteners and wire locations
• Disconnect wiring harness and replace the switch assembly; ensure secure mounting and correct connector seating

This access door key operates the factory lock on select appliances. It replaces a lost or worn key so you can securely lock or unlock the access door and restore normal, controlled access to the compartment.

• Locks or unlocks the access door via the built-in lock cylinder
• Restores function when the original key is missing, bent, or broken
• Helps resolve situations where the door can't be opened or secured due to a worn key
• Maintains restricted access to the compartment when needed

• Verify this key matches your model's lock; keys are not universal
• Insert fully and turn gently—do not force a stuck lock
• If the lock cylinder is damaged or seized, replace the lock assembly
• Disconnect power if removing the door or servicing internal components

This tub displacement switch monitors water level/pressure to help the washer detect tub fill and balance, reducing overfill and load sensing errors. It replaces a worn or faulty unit to restore reliable fill and balance sensing. What it does:

• Senses tub water displacement/pressure changes so the washer can detect correct fill and load balance
• Helps prevent overfilling and supports proper spin cycles by reporting tub condition to the control
• Commonly replaced when washer overfills, won't start spin, or shows erratic fill behavior

• Disconnect power before accessing internal components to avoid shock
• Mounts to the washer chassis with electrical connector and vacuum/pressure hose; reuse existing hose if undamaged
• Verify hose and fittings are intact and free of blockages before installation

This Smart ATC temperature switch senses and helps regulate oven temperature for more consistent cooking. It replaces a failed switch to restore correct temperature feedback to the range control for accurate heating. What it does:

• Detects oven temperature and sends a signal to the control so heating elements cycle appropriately
• Helps correct issues where the oven runs too hot, too cold, or cycles erratically
• Works as part of the temperature control system—does not include the main control board
• Replaces a worn or failed temperature/A.T.C. sensor switch to restore proper temperature sensing

• One temperature switch (Smart ATC)

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Access typically requires removing the oven control panel or back panel; keep track of screws and wire connections
• Handle the switch and connector gently to avoid damage; verify wiring matches original before reconnecting

This pressure switch senses pressure changes and signals the appliance control to start or stop functions, helping restore proper operation when pressure-based controls fail. It's a direct-replacement style switch used in compatible Frigidaire appliances. What it does:

• Detects and closes or opens an electrical circuit based on air or water pressure changes
• Signals the control board to advance cycles or enable components (pump, valve, blower)
• Common symptom indicator: appliance won't complete cycles or responds inconsistently when pressure-controlled
• Helps stop operation when pressure limits are reached to protect system components

• One pressure switch

• Disconnect power (and water, if applicable) before starting work
• Handle the switch and its terminals with care; avoid bending pins or cracking the housing
• Inspect and replace any associated tubing or fittings that are cracked or clogged

This is a replacement GR 800 key for machines equipped with GR 800 locks. It restores secure, authorized access to locked compartments when the original key is lost or damaged, or when an extra key is needed.

• Operates locks designated with the GR 800 key code on compatible equipment
• Helps resolve issues like being unable to unlock a GR 800 lock due to a missing or broken key
• Useful for adding spare keys for daily operations and collections
• Works only with GR 800 code locks; code must match your lock

• Insert the key fully and turn gently; do not force if resistance is felt
• If accessing internal components after unlocking, disconnect power and follow safety procedures
• Replace worn or malfunctioning locks for reliable operation

This compressor start relay helps the refrigerator compressor start reliably so the appliance can cool properly. It replaces a failed relay to restore normal compressor startup and reduce hard-start symptoms. What it does:

• Supplies the compressor's start winding with a timed boost to initiate motor start
• Helps prevent repeated clicking or humming when the compressor struggles to start
• Commonly used when the refrigerator is warm, not cooling, or the compressor does not run
• Works with the compressor start circuit as a replacement electrical relay

• Disconnect power to the appliance before accessing the compressor or electrical components
• Replace the relay on the compressor terminal block; ensure firm, correct terminal seating
• Inspect the compressor and start capacitor for related faults while servicing