267Abrs Parts

Won't start, spin light blinking, or won't stop spinning? This control board manages cycles and settings. Common DIY repair, typically installed in minutes.

These mounting screws secure various internal components within your washing machine. They hold parts like panels, brackets, and mechanisms in their proper positions during wash cycles. Replace if screws are missing, stripped, or causing rattling noises during operation.

Washer won't respond to cycle selections? This selector switch mounts behind the control knob to restore reliable setting changes. Easy DIY fix.

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed

Idler arm assembly mounts to the dryer frame and maintains proper belt tension on the drum. Replace if the arm is cracked, bent, or the pulley is worn.

Seals the dryer door to prevent heat and moisture loss. Replace when worn or damaged to restore drying efficiency and stop lint escape. Verify fit.

Dryer won't start, clicks but drum doesn't turn, or makes grinding noise? This motor and pulley assembly powers the drum and blower. Moderate DIY repair.

Secures components inside your washer to prevent movement, loose connections, and rattling noise. Replace when worn or missing to restore stability.

This washer motor run capacitor stores and releases electrical energy to help the drive motor start and run smoothly. Replacing a weak capacitor can help restore consistent agitation and spin and reduce motor humming or stalling under load.

• Provides the phase shift and torque assist the drive motor needs to start and stay running
• Can address: washer won't start, no agitate or spin, motor only hums/buzzes, or stops under load
• Visible clues of failure can include a swollen, cracked, or leaking capacitor case

• Unplug the appliance before servicing; capacitors can retain a charge even when power is off
• Discharge the capacitor safely before handling
• Note wire positions; move leads to the same terminals and secure the capacitor in the original bracket/orientation
• Inspect connectors and replace any burnt or loose terminals to ensure a tight fit

Fix bleach pooling or uneven dispensing in your laundry center. This funnel directs bleach into the wash tub, preventing spills and odor issues.

Front suspension rod assembly that supports and stabilizes the washer tub. Replace if rod is bent, damaged, or worn to restore proper tub alignment.

Washer not cleaning clothes properly? This agitator assembly creates the wash action that moves laundry through water. Moderately difficult replacement.

Restores the dryer's front airflow path and drum seal. Replace if the duct is damaged, cracked, or the felt seal is worn, compressed, or missing.

Rear suspension rod assembly that supports and stabilizes the washer tub from the back of the cabinet. Replace if worn, broken, or cracked to restore balance.

This transmission and support assembly drives and stabilizes the wash basket. It converts motor power into agitation and spin while supporting the tub, helping resolve no-agitate/no-spin complaints and loud operation for reliable cleaning performance.

• Transfers motor power to the drive system for agitation and spin
• Supports the basket and helps maintain alignment during operation
• Helps correct no agitate, no spin, or weak/intermittent spin
• Can address grinding/rumbling noises or oil traces from the center

• Disconnect power and water before servicing; wear gloves and eye protection
• Appliance and assembly are heavy—use assistance and protect flooring
• Removal typically requires accessing from top and bottom to remove agitator/basket and drive hardware
• After installation, run a test cycle to ensure smooth agitation, proper spin, and no leaks