665-158 19990 Parts

This circulation pump and motor assembly moves wash water through your dishwasher's spray arms to clean dishes. Replace a worn or seized wash motor to restore proper spray pressure, quieter operation, and consistent cleaning performance.

• Circulates wash water through the spray arms during wash and rinse cycles
• Restores cleaning performance when the original wash motor won't run or is weak
• Typical symptoms: no/weak spray action, dishes still dirty, loud humming or grinding during wash
• Leaks at the pump housing or shaft area can indicate the assembly has failed

• Disconnect power at the breaker and shut off the water supply before servicing
• Remove the toe panel and slide the dishwasher out to access the underside
• Have a towel or pan ready for residual water; disconnect wiring and hoses, noting their orientation
• Transfer and secure existing clamps/mounting hardware as needed; ensure seals are properly seated and test for leaks after reassembly

This small check ball sits inside a check valve to allow one-way water flow. Replacing a worn or missing ball helps prevent backflow and supports reliable draining performance between cycles.

• Maintains one-way flow through the valve to stop water from returning after the pump stops
• Helps ensure complete, consistent draining
• A damaged, swollen, or missing ball can let water back up into the tub/sump
• Contribute to slow or intermittent draining and unusual gurgling/flow noises

• Disconnect power and shut off water before servicing
• Access the check valve assembly per your model's service information (commonly at the sump, pump outlet, or drain connection)
• Clean the valve seat/passage; remove debris that could prevent sealing
• Place the ball in the valve seat as shown in your model's parts diagram; reassemble and test for leaks and proper flow

This is a tine pivot clip that is a part of the dishrack on many models of dishwashers. The purpose of the plastic tine pivot clip is to secure the tine row onto the dishrack so it stays in the correct place. Sometimes, the tine pivot clip can be damaged or cracked through typical use. When this occurs, the tine row may move out of place and cause noise or other damage to the dishwasher. If a visual inspection shows damage to the tine pivot clip, it should be replaced.Work gloves will be needed to replace the tine pivot clip. In most cases, the replacement can be done by hand but pliers may also be useful. Unplug the dishwasher and disconnect the water before making the replacement. Open the dishwasher and gain access to the tine pivot clip. Pull it out of the dishwasher and install the new replacement part. Make sure to reconnect the water and power before use.This is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as a single part. The tine pivot clip is designed to be compatible with dishwashers manufactured by Kenmore, KitchenAid, and Whirlpool.

Color: Almond

This is the upper spray arm that distributes wash water to the top rack. Replacing a cracked, warped, or clogged arm restores even spray coverage and helps the arm spin freely so glasses and bowls come out consistently clean.

• Directs high-pressure jets to the upper rack and rotates under water pressure for full coverage
• Maintains even water distribution to improve cleaning performance
• Common symptoms of a failed arm: top-rack items not getting clean, arm not spinning, uneven spray, cracks or clogged nozzles

• Disconnect power and water supply before servicing the dishwasher
• Remove or lower the upper rack if needed; release the retaining nut/clip and pull the old arm straight off
• Seat the new arm fully on the hub/manifold and secure the retainer; verify it spins freely
• Run a short test cycle to ensure proper spray and operation

Comes with seal.

Comes with axle clip.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This vent screen covers the dishwasher door vent, allowing steam to escape while blocking food particles and debris. Replacing a damaged or missing screen helps maintain proper airflow and can reduce moisture and odors around the vent area.

• Screens the door vent to keep debris out of the vent duct and fan path
• Maintains airflow for venting steam during the dry cycle
• A clogged, cracked, or missing screen may lead to moisture at the vent, odors, or reduced drying performance
• Replace if warped, broken, or lost during service

• Disconnect power to the dishwasher at the breaker before servicing
• Open the door and remove inner-door screws to access the vent assembly
• Remove the old screen, seat the new screen fully and evenly, then reassemble without overtightening
• Run a short cycle and check the vent area for proper airflow and moisture

Replacement 8-32-thread screw used to secure panels, brackets and small components in compatible household appliances. Restores missing or stripped fasteners so panels and parts stay firmly attached during normal use. What it does:

• Secures trim, panels, brackets and control housings to maintain proper assembly.
• Replaces missing or damaged screws that can cause rattling, loose panels or misaligned components.
• Fits locations that require an 8-32 threaded fastener; correct length and head style for your application.
• Helps restore stable, vibration-free operation when worn or stripped fasteners are replaced.

• Disconnect power and water before servicing; wear eye protection and gloves.
• Use the correct screwdriver or driver bit to avoid stripping the screw head.
• Do not overtighten—turn until snug and secure to avoid damaging threads or surrounding parts.
• If the original used a washer or nut, reuse or replace as needed and the screw length and head type match the original.

Screw: 8-16 x 3/8 inch.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Size: 8-18 x 1/2 inch.

For mating terminal use WP94614.

This door catch and strike work together to keep the door securely closed and engage the safety interlock switch. Replacing worn pieces restores a firm latch and reliable operation when the door is properly shut.

• Aligns and engages the latch so the door stays closed during operation
• Activates the door switch so cycles can start
• Helps prevent the door from popping open mid-cycle
• Common symptoms: door won't latch without force, unit won't start, visible wear or a bent strike

• Disconnect power to the appliance before servicing
• Open the door and remove mounting fasteners to swap the catch and strike
• Adjust strike alignment/depth so the latch engages fully and the door sits flush
• Restore power and test for smooth closing and proper cycle start

For mating terminal use [AP31136300].