Atlantis Nde7400ayw Parts

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

To order indicator lens use WP22001948.

This suspension spring hook connects a tub suspension spring to the washer frame, helping support and center the wash basket. Replacing a worn or missing hook can reduce shaking, banging, and off-balance interruptions during spin.

• Secures one end of a suspension spring to the cabinet/base
• Helps control tub movement and absorb vibration during agitation and spin
• Failure signs include excessive vibration or banging, tub leaning/sagging, or frequent out-of-balance stops

• Disconnect power and water; wear gloves and eye protection
• Access the suspension area per model; support the tub to relieve spring tension
• Use pliers or a spring tool to remove the old hook; note orientation and mounting location
• Seat the new hook fully and ensure the spring is engaged securely before reassembly and testing

This timer controls the sequence and duration of your washer's cycles. When its internal contacts wear or stick, the machine can stall or fail to advance. Replacing it restores reliable, automatic cycle progression.

• Advances the washer through fill, wash, rinse, drain, and spin in the programmed order
• Sends power to the water inlet valves, drive motor, and drain pump at the correct times
• Common symptoms include a cycle that won't advance, stops mid-cycle, or only progresses when the knob is turned by hand
• Also causes cycles to skip steps or run much longer/shorter than expected

• Disconnect power and shut off water before servicing
• Open the control console; remove the rear panel/cover to access the timer
• Move wires from the old timer to the new unit one at a time to maintain placement; secure the timer with its mounting screws
• Reinstall the dial/knob if applicable, reassemble the console, and run a test cycle to operation

Hose washer and plastic insert for inlet hose. To order separately: for washer use WPY013783, for strainer use WP22002960.

This small retaining clip secures components in place inside the appliance, helping prevent movement, vibration, and premature wear. Replace a bent, fatigued, or missing clip to restore a solid, factory-tight hold.

• Holds panels, brackets, or tubing securely in their mounts
• Helps maintain alignment to reduce rattles, rubbing, or intermittent issues
• Common signs of failure: missing clip, loose fit, buzzing/vibration, parts that won't stay seated
• Restores proper retention after service, transport, or vibration-related fatigue

• Disconnect power and shut off gas/water before servicing
• Note the original clip's orientation; remove with needle-nose pliers
• Seat the new clip fully—do not over-bend; spring tension provides the hold
• Test operation before reassembly

This retaining ring secures a component on a shaft or within a groove so it stays aligned during operation. Replacing a bent, rusted, or missing ring helps stop wobble, noise, and parts working loose.

• Locks into a groove to keep gears, pulleys, wheels, or spacers from sliding off a shaft
• Helps maintain proper spacing and alignment of moving parts
• Common signs of failure: wobbling parts, scraping/rubbing noises, or components that work loose
• Visual clues: deformation, corrosion, or loss of spring tension

• Disconnect power and any utilities to the appliance before service
• Wear eye protection—retaining rings can spring free under tension
• Note the order/orientation of any washers or spacers before removal
• Use appropriate snap-ring or needle-nose pliers and ensure the ring seats fully in its groove

Color: chrome. The main part of the knob is about 1 inch in diameter. The handle is about 2 inches.

This washer tub mounting bolt secures the tub assembly to its support points. Replacing worn or missing hardware helps keep the tub aligned and stable through wash and spin, reducing vibration and noise. What it does:

• Anchors the tub assembly to its mounting bracket or frame
• Helps maintain alignment under load and during high-speed spin
• Replace if the bolt is stripped, rounded, rusted, or missing
• Symptoms can include excessive vibration/banging, tub shifting or scraping, and rattling hardware

• 1 mounting bolt

• Disconnect power and water before servicing; wear appropriate PPE
• Support the tub to relieve stress on the mounting points before removal
• Start threads by hand to avoid cross-threading; tighten bolts evenly across all mount points
• Do not overtighten; follow for torque guidance

Screw: 8-16 x 3/8 inch.

Drive motor isolator.

Specs: No.8X1/2 HEX WASHER HEAD

Size: 10-24 x 3/8 inch.

Motor plate isolator.

This motor isolator is a rubber mounting that cushions and secures the washer motor, reducing vibration and noise during spin cycles and helping protect the motor and chassis from premature wear. What it does:

• Cushions the motor to reduce vibration and minimize rattle and noise during operation
• Keeps the motor properly positioned to prevent rubbing or misalignment
• Helps protect motor and surrounding components from shock and movement
• Common symptom linkage: excessive vibration, loud noise during spin, or visible motor shifting

• Disconnect power to the appliance before starting any work.
• This part mounts between the motor and chassis; access typically requires tilting or removing the washer cabinet or accessing the underside.
• Inspect adjacent mounts and fasteners; replace any worn hardware and use the exact OEM part for proper fit.

This water inlet valve controls water flow into the appliance so it fills only when needed, restoring proper fill cycles and preventing overfilling or no-fill problems. Replaces a worn or failed inlet valve to recover normal operation. What it does:

• Opens and closes water flow to the appliance during fill cycles
• Helps maintain correct water level for proper operation
• Commonly replaces failed valves that cause no water, slow fill, or continuous filling
• Stops water flow when the cycle is finished to prevent overfilling or flooding

• Disconnect power and shut off the water supply before starting any repair.
• Verify inlet hoses and fittings are in good condition; replace if damaged.
• Installation typically requires basic hand tools and may involve disconnecting hoses and electrical connectors.
• After installation, restore power and water, then run a short cycle and check for proper fill and leaks.