Cye23tsdss Parts

This Mullion Spring Sleeve is the small bushing that fits over the door mullion (center flipper) spring. It guides the pivot and reduces wear so the flap folds smoothly and helps maintain a tight seal between refrigerator doors.

• Provides a smooth bearing surface around the mullion spring/hinge pin for reliable pivoting
• Helps the mullion fold out on opening and spring back to close the center gap
• Wear or loss may present as a loose or binding flipper, clicking/grinding, or a gap that prevents a full seal
• Replacing the sleeve can help restore proper flipper action without replacing the entire mullion assembly

• Disconnect power and clear items from the door; remove the mullion from its top and bottom pivots, noting the spring orientation
• Slide off the worn sleeve from the spring/pin and install the new sleeve in the same position
• Reinstall the spring and mullion; verify the flipper opens/closes freely and the center seal makes full contact
• Wear cut-resistant gloves; edges around the door and hinge can be sharp

This refrigerator display assembly replaces a damaged or unresponsive front control panel. It restores clear status indication and responsive controls so everyday settings are easy to see and select.

• Provides the user interface and status display for key refrigerator functions
• Sends control inputs from the touchpad/buttons to the appliance's electronics
• Ideal replacement for cracked, faded, or unresponsive display panels
• Common symptoms: blank or dim display, controls not responding, intermittent operation, or cosmetic damage

• Disconnect power to the refrigerator before servicing
• Remove trim/drip tray and mounting screws; release locking tabs to pull the panel forward
• Disconnect wire harness connectors carefully; avoid pulling on wires or ribbon cables
• Reconnect harnesses, seat the new assembly, secure fasteners, restore power, and test

This screw fastens appliance panels, brackets, and trim so parts stay secure and aligned. Replace a missing, stripped, or rusty screw to stop rattles and restore a tight, factory fit.

• Secures covers, brackets, and trim to the appliance cabinet or liner
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration noise and loose or misaligned parts
• Maintains proper fit of guards, kickplates, or internal panels

• Disconnect power; turn off water supply if working near water lines
• Match to the original fastener to size and thread
• Start threads by hand to avoid cross-threading; tighten snugly, not excessively
• If threading into plastic, avoid overtightening to prevent damage

This Duct Door Spring returns the dispenser ice chute door to the closed position and helps maintain a tight seal at the dispenser opening, reducing warm-air leaks, frost buildup, and melting or clumping ice.

• Provides the return tension for the dispenser duct/ice chute door after dispensing
• Helps keep cold air in and warm air out to limit frost and condensation at the dispenser
• Can reduce frost in the ice chute or ice clumping caused by air leaks

• Disconnect power to the refrigerator before servicing the dispenser
• Access the dispenser assembly; remove front panel/trim as required by your model
• Note spring orientation and engage it correctly on the duct door and pivot
• After installation, verify the door moves freely and seals fully before reassembly

This vegetable pan is the refrigerator's crisper drawer for storing produce in the fresh food compartment. Replacing a cracked or missing bin restores smooth sliding performance and organized storage to help keep fruits and vegetables in good condition.

• Stores produce in the fresh food section; works with the crisper cover/humidity system to help maintain produce quality
• Slides on factory rails for easy access and organization
• Typical failure signs: cracks or chips, broken tabs or front lip, drawer sticks, falls off track, or is missing
• Replacing removes sharp edges and prevents spills or items dropping beneath the drawer

• Remove food and lift out the damaged bin; if a glass cover rests on the pan, lift it off carefully and set aside
• Inspect and clean the drawer tracks; remove debris before installing the new bin
• Align the new pan with the side rails and slide straight in until fully seated—do not force
• Handle glass components carefully; consider gloves to protect hands

Ice bucket and motor kit replaces a worn or cracked ice bin and its drive motor so your refrigerator can collect and advance ice properly. Restores ice storage and rotation for reliable dispensing. What it does:

• Holds and stores produced ice in the freezer's ice compartment.
• Drive motor rotates the bucket to advance ice toward the dispenser or ice chute.
• Replaces a cracked or damaged bin that leaks or chips ice.
• Helps stop symptoms such as a non-turning bucket, ice not dispensing, or unusual motor noise.

• Disconnect power to the appliance before starting any repair.
• Handle the bin and motor carefully to avoid damaging mounting tabs and electrical connections.
• Use basic hand tools; follow the OEM service manual or exploded parts diagram for correct removal and reassembly.
• After installation, reconnect power and cycle the ice maker to verify proper rotation and ice delivery.

This latch bushing is a small sleeve used in the refrigerator's latch mechanism. It supports the latch pivot, reduces wear, and helps the latch engage smoothly so doors, bins, or covers close securely and stay in place.

• Provides a smooth, low-friction pivot surface for the latch pin/shaft
• Helps maintain proper latch alignment and engagement
• Reduces play and noise within the latch mechanism
• Symptoms of a worn bushing can include a loose or sticky latch, difficulty latching, or squeaking/grinding in the latch area

• Disconnect power to the refrigerator before servicing
• Access the latch assembly; note the orientation of the existing bushing and any spring/pin
• Press the new bushing into place without forcing or deforming the housing
• Reassemble and test for smooth latch operation; inspect related parts (pin, spring) and replace if worn

This fresh food duct tower assembly channels cold air from the refrigerator's cooling system and distributes it throughout the compartment. Replacing a cracked or warped tower restores proper airflow and helps maintain even, consistent temperatures between shelves.

• Directs and distributes airflow through the fresh food section to reduce hot and cold spots
• Helps maintain an air-tight path to prevent leaks and airflow noise
• Supports proper temperature regulation for food storage
• Typical symptoms: uneven cooling in the fridge, weak airflow from tower vents, visible cracks/broken tabs, or rattling behind the tower

• Disconnect power before servicing; wear cut-resistant gloves
• Remove food and shelves for access; release screws/tabs and lift the old tower straight off the rear duct
• Transfer any reusable clips, seals, or covers from the original part
• Seat the new tower evenly over the duct and secure fasteners snugly; restore power and allow up to 24 hours for temperatures to stabilize

This 1/4-inch quick-connect locking clip secures water tubing in push-to-connect fittings on your refrigerator's water and ice system. It locks the tube in place to help prevent leaks and accidental disconnection at the fitting. What it does:

• Locks 1/4-inch OD tubing into compatible push-to-connect fittings
• Helps maintain a secure seal to reduce drips at water line connections
• Replaces a missing, cracked, or loose clip on filter heads, inlet valves, or inline couplers
• Symptoms include leaks at a fitting or a tube that won't stay seated

• One 1/4-inch quick-connect locking clip

• Disconnect power and shut off the water supply before servicing; dispense water to relieve pressure
• Remove the old clip; ensure the tubing end is clean and cut square
• Fully insert the tube into the fitting until it bottoms out, tug lightly to seat, then install the clip in the collet groove
• Restore water and check all connections for leaks

• Designed for fittings that use 1/4-inch OD tubing. It will not fit 5/16-inch or 3/8-inch quick-connect fittings.

The Ice Bucket and Crusher is an OEM component for GE side-by-side refrigerators equipped with an internal ice system and ice crusher feature. Located in the freezer section, it provides filtered ice-crushing and storage abilities. Consistent icemaking depends on an intact ice-handling mechanism. 

Symptoms of a faulty bucket and crusher include:

• Gradual accumulation of uncrushed ice cubes within the storage bin  
• Drive motor straining or temporarily ceasing during heavy usage
• Partial blockage of ice chute restricting flow into glasses

Causes range from mineral contamination slowing mechanical components to wear from constant high-volume usage dulling edges or linkages over time. Regular cleaning helps but replacement maintains long-term efficiency.

Replacing with this genuine GE bucket and crusher restores optimized ice handling performance through engineered durability and precision mechanisms. Compatible replacements suit Hotpoint, RCA, or Kenmore models seeking automated, whole-home ice production and retrieval cycles without interruption.
 

This valve body assembly routes and supports the refrigerator's water flow for the dispenser and ice maker. Replacing a cracked or leaking body restores proper water delivery and helps prevent leaks at the rear of the unit.

• Directs incoming water to the dispenser and/or ice maker
• Maintains sealed connections for water lines and valve components
• Helps resolve leaks around the rear valve area
• Symptoms can include no/slow dispenser flow or an ice maker not filling

• Unplug the refrigerator and shut off the household water supply
• Relieve line pressure; place a towel or container to catch residual water
• Note tubing and wire positions; transfer to the new assembly and ensure every connection is fully seated
• Restore water and power, then check all joints for leaks while dispensing and during an ice maker fill

This roller assembly helps refrigerator drawers and baskets glide smoothly along their tracks. When the wheel or bracket wears or breaks, drawers can stick, scrape, or sit unevenly—replacing the roller restores easy, consistent movement.

• Supports and guides a drawer or basket on its track
• Restores smooth in-and-out sliding action
• Replaces a cracked, worn, or missing wheel/bracket
• Common symptoms: drawer hard to open/close, scraping noise, drawer tilts or drops

• Disconnect power and remove the affected drawer/shelf to access the roller
• Note orientation; remove retaining screw or clip and detach the old roller
• Position and secure the new roller—avoid overtightening into plastic
• Reinstall and test the drawer; clean the tracks and check for damage or misalignment

This is the hinge for the refrigerator door mullion—the folding center rail (flipper) between the doors. It lets the mullion pivot smoothly and seal the door gap, helping prevent air leaks, condensation, and poor door closure.

• Allows the mullion to fold open and closed with door movement
• Helps maintain an even, airtight center seal between doors and gaskets
• Common fix for a broken/loose flipper or a mullion that won't pivot or return
• Resolve doors not closing fully, air leaks, or condensation along the center rail

• Unplug the refrigerator before servicing
• Support the door and mullion to avoid stressing hinges and gaskets
• Note hinge orientation and screw locations during removal; reuse existing hardware
• After installation, verify smooth mullion action and a proper center seal

A replacement bracket that secures the refrigerator water-filter manifold to the cabinet, keeping the filter head stable and properly aligned so the filter seats correctly and helps reduce leaks and vibration during use. What it does:

• Secures and supports the water-filter manifold assembly to the refrigerator cabinet.
• Keeps the filter head aligned so the filter cartridge seals correctly.
• Helps prevent movement-related leaks or disconnections of the water lines.
• Replaces bent, cracked or missing brackets that can allow the filter housing to shift.

• Turn off water supply and unplug the appliance before beginning; have a towel or small container ready to catch residual water.
• Remove the filter or access panel as needed to reach the manifold; keep fasteners for reuse or replace if damaged.
• Use common hand tools (screwdriver/socket) and install bracket in the same orientation as the original; do not overtighten mounting hardware.
• After installation, restore water and power, check for leaks, and confirm the filter seats and dispenses properly.

This left-hand slide bracket supports the drawer rail inside the refrigerator, keeping the drawer aligned so it opens and closes smoothly. Replace a cracked or warped bracket to restore proper drawer glide and prevent binding or sagging.

• Supports and aligns the drawer slide/rail on the left side
• Helps the drawer glide smoothly and stay level
• Replace if the bracket is cracked, deformed, or broken
• Common symptoms: drawer sticks, tilts, comes off track, or won't close fully

• Disconnect power before servicing; remove the drawer and any obstructing shelves
• Left/right orientation is as you face the front of the appliance
• Retain mounting screws during removal and reinstall the bracket securely
• Test drawer travel for smooth, even operation after installation

The Mullion Striker is an OEM part for GE refrigerators responsible for securing the mullion or flipper door in place when it is closed, ensuring a tight seal and temperature inside the refrigerator.

A bad mullion striker can be caused by normal wear and tear over time, damage due to excessive force or impact, or misalignment of the mullion assembly. If you notice that the mullion door does not stay securely closed, causing a gap or allowing warm air to enter the refrigerator, it may indicate a problem with the mullion striker.

Symptoms of a bad mullion striker include:

• Difficulty in keeping the mullion door closed
• Visible gaps or improper sealing when the door is closed
• Condensation or frost buildup around the mullion area
• Unusual noises from the mullion assembly

Replace your faulty mullion striker with this genuine OEM part to restore your refrigerator. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.