Eimed55imbo Parts

The Adjustable Foot is an OEM part for Frigidaire dryers. This part is located at the bottom of the dryer and allows you to level it, ensuring stability and proper operation. 

Causes of a bad adjustable foot can include regular wear and tear, damage from moving the appliance, or breaking due to excessive weight or stress.  

Symptoms of a bad adjustable foot include:

• The dryer wobbling or tilting
• Difficulty in adjusting the height of the foot
• Visible damage or deformation of the foot
• Unusual noises or vibrations during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This line noise filter conditions incoming AC power by reducing electromagnetic interference before it reaches the appliance's electronics. Replacing a shorted or damaged filter can restore stable operation and help prevent erratic control behavior.

• Filters EMI/RFI on the power line before it reaches the control system
• Helps protect sensitive electronics from interference and voltage spikes
• Failure may present as no power, intermittent resets, or nuisance GFCI/breaker trips
• Typically mounted near the power-cord entry; also called a line filter

• Disconnect power and allow any capacitors to discharge before servicing
• Note wire positions and line vs. load orientation; take a photo before removal
• Secure the ground and mount the new filter firmly to the chassis
• Route and reconnect wires carefully to avoid pinching; reassemble and test

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This thermistor is the temperature-sensing component that feeds accurate readings to the appliance's control. Replacing a faulty sensor restores proper temperature feedback, helping the control run cycles correctly and reduce temperature-related performance issues. What it does:

• Monitors temperature and changes resistance with temperature (NTC), sending a signal to the control board
• Helps the control regulate heating or water-temperature management during operation
• When open/shorted or out of range, can trigger temperature/sensor error codes
• Symptoms include inconsistent temperatures, long run times, or cycles that won't complete

• 1 thermistor

• Disconnect power before servicing; shut off gas/water supply if applicable
• Access the sensor per your model; it's typically secured by a clip or screw and connects via a wire harness
• Note wire orientation; avoid pulling on wires and ensure the connector is fully seated
• After installation, clear any stored error codes and run a diagnostic or test cycle

This dryer blower moves air through the drum, lint filter, and exhaust so laundry dries efficiently. Replacing a damaged blower restores proper airflow and helps prevent long dry times and overheating issues.

• Draws and circulates air across the heater, through the drum and lint filter, and out the vent
• Maintains correct airflow and temperature control for consistent drying performance
• Worn, cracked, or clogged blowers may cause weak exhaust airflow and extended dry cycles
• May also present as rattling/grinding noises from the blower area or high-heat shutoffs

• Disconnect power; if gas, turn off gas supply before servicing
• Access the blower by removing the front/lower panel and blower cover
• Clean lint/debris from the housing and duct; transfer any seals or hardware from the original as needed
• After installation, spin the blower by hand to verify free movement; reassemble and test airflow

Replace a failed thermistor with this factory temperature sensor. It monitors temperature and feeds that data to the control, helping the appliance regulate heat and run cycles correctly. A faulty sensor can cause temperature-related performance issues.

• Senses temperature and sends a resistance signal to the control board for regulation
• Helps maintain proper heating/temperature during operation
• Failure may cause no heat or overheating, erratic or extended cycles, or temperature/sensor error codes
• Replace when sensor is open/shorted or readings are out of range per service diagnostics

• Disconnect power before servicing; if applicable, also shut off water or gas supply
• Access the sensor, unplug the wire connector, and remove any mounting screw/clip
• Install the new sensor; transfer any bracket/seal from the original and route wiring away from hot or moving parts
• Run a diagnostic or test cycle after replacement to confirm normal operation

The Motor Mounting Clamp is an OEM part for Frigidaire dryers. This clamp secures the motor in place within the dryer, ensuring it operates smoothly and remains stable during the drying cycles. The motor mounting clamp is essential for maintaining the proper alignment and function of the dryer motor.

Over time, the motor mounting clamp can become worn out or damaged due to constant vibration and movement. Accidental impacts or mishandling during maintenance can also cause the clamp to fail, leading to motor misalignment or instability.

Symptoms of a bad motor mounting clamp include:

• Excessive noise or vibration during the drying cycle
• Motor shifting or moving within the dryer
• Reduced drying efficiency
• The dryer not starting or stopping abruptly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This metric machine screw features an M5 x 0.8 thread used to secure panels and assemblies inside your appliance. Replacing missing or damaged hardware restores a tight, rattle-free fit and helps maintain proper alignment of parts.

• Fastens appliance components using an M5 x 0.8 machine-thread
• Replaces missing, loose, or stripped screws
• Helps reduce vibration and rattling noises
• Maintains correct alignment of brackets, panels, or internal assemblies

• Disconnect power before servicing; if working near water connections, shut off the supply.
• Match thread and length to the original screw and replace in the same location.
• Start threading by hand to avoid cross-threading; use the correct driver and do not overtighten.
• Reinstall any original washers or lock hardware used with the screw.

This gasket forms a tight seal between mating components in your appliance, helping contain water, air, or heat as designed. Replacing a worn gasket restores proper sealing and helps prevent leaks, performance loss, and residue buildup. What it does:

• Creates a compressible seal between two parts to prevent leakage and maintain proper airflow or water containment
• Helps reduce rattles and wear at the joint by cushioning the connection
• Supports efficiency and consistent performance by keeping the system properly sealed
• Common symptoms of failure: visible cracks/tears or flattening, leakage at the joint, heat or moisture escaping, or persistent odors near the seal

• 1 gasket

• Disconnect power; shut off water supply before servicing
• Note the gasket's orientation and take reference photos during disassembly
• Remove the old gasket and thoroughly clean mating surfaces of residue or debris
• Seat the new gasket evenly without stretching; reassemble and test for a proper seal

The Support Roller Washer is an OEM part for Frigidaire dryers, designed to ensure the smooth and stable operation of the dryer drum. Positioned between the support roller and the shaft, this washer plays a critical role in reducing friction and wear, allowing the drum to rotate smoothly and quietly.

Causes of these symptoms often stem from normal wear and tear, which can lead to the degradation of the washer over time.  

Symptoms of a bad Dryer Support Roller Washer include:

• Unusual noises, such as squeaking or grinding, indicating increased friction during drum rotation
• The dryer drum appears to wobble or is misaligned during operation
• Increased vibration of the dryer, which can lead to wear on other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door switch detects whether the appliance door is open or closed. A working switch lets the machine start when the door is fully shut and stops operation when the door opens for safety.

• Monitors door position and allows the cycle to run only when closed
• Interrupts power to stop operation when the door opens
• Common symptoms of a failing switch: appliance won't start with the door closed, must press/hold the door to run, interior light stuck on/off, or a "door open" message on models with a display

• Disconnect power to the appliance before servicing
• Access the switch at the door opening/front panel; release mounting screws or locking tabs and remove the switch
• Move wires to the new switch one at a time to maintain correct positions
• After reassembly, test switch operation before running a cycle

This factory fastener secures appliance components and cabinet panels. Replacing a stripped, rusted, or missing screw restores a tight fit, reduces rattles and vibration, and keeps parts aligned for reliable operation. What it does:

• Fastens brackets, panels, and internal components to the cabinet/frame
• Helps maintain alignment and stability under vibration
• Direct replacement when the original is lost, corroded, or threads are damaged
• Common symptoms: loose or rattling panels, gaps/misalignment, or visibly missing hardware

• 1 screw

• Disconnect power; shut off gas/water if applicable before servicing
• Support the panel or component while removing/starting screws
• Match location and length to the original; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping

This small spacer fits on the idler assembly shaft to properly space and align the belt tensioner. Replacing a worn spacer helps keep the drive belt tracking correctly so the drum/tub runs smoothly and quietly. What it does:

• Spaces and centers the idler pulley on its shaft
• Helps maintain proper belt alignment and tension
• Can reduce squeaking or chirping from the idler area
• A worn or missing spacer may let the belt ride off, fray, or stop the drum/tub

• 1 idler spacer

• Disconnect power before servicing; let hot components cool
• Access the idler assembly per your model, relieve belt tension, and remove retaining hardware to slide off the pulley and old spacer
• Install the new spacer in the same location/orientation; reassemble and route the belt correctly
• Rotate the drum/tub by hand to verify smooth belt tracking before restoring power

Replacement striker for the refrigerator door latch that provides the catch point for the door to close securely. Restores proper door engagement to help maintain a tight seal and consistent internal temperature. What it does:

• Provides the catch point for the door latch so the door closes and stays latched
• Helps maintain an effective door seal to preserve cooling performance
• Common symptom: door won't stay closed, pops open, or fails to latch
• Also helps reduce drafts and noise caused by a misaligned latch

• Turn off power to the appliance before starting work
• Access the striker area, remove mounting fasteners, and replace with the new striker
• Align the striker so the latch engages smoothly; tighten screws securely
• Use care not to overtighten or strip mounting holes; replace damaged hardware as needed

This clip is a hose clamp used in select laundry appliances. It secures a hose connection to prevent leaks and keep water or air moving where it should, helping maintain reliable washer or dryer performance.

• Secures hose to its fitting to prevent leaks or disconnections
• Helps resolve issues like leaking at a hose joint, loose hose, or poor draining/airflow related to a slipped hose
• Durable spring-style clamp designed for repeatable tension
• Commonly used on internal washer or dryer hose connections

• Unplug the appliance and turn off water supply before service
• Have a towel or pan ready for residual water when removing hoses
• Use pliers to compress and slide the clamp; note original clamp position for reassembly
• Inspect hose ends for cracks; replace the hose if damaged before reinstalling the clamp

This terminal block provides the mounting point and secure electrical connection for the appliance power leads. Replacing a damaged or corroded terminal block restores a solid power connection and reduces arcing or intermittent power. What it does:

• Provides a secure connection between the incoming power cord and the appliance wiring
• Holds and isolates power terminals to prevent shorting and arcing
• Commonly fails when terminals are burned, corroded, loose, or when wires heat at the connection
• Symptoms of a failing terminal include loss of power, intermittent power, visible burn marks or arcing at the connection, and melted or discolored insulation

• One terminal block

• Always disconnect power at the breaker or unplug the appliance before servicing
• Tighten mounting screws and terminal screws securely; inspect and replace any damaged wire insulation