Ffle4033qto Parts

This sensor monitors appliance conditions and relays a signal to the control so heating, cooling, or cycle functions occur at the right time. Replacing a failing sensor restores accurate feedback and more reliable operation.

• Detects operating conditions and sends signals to the control board
• Helps regulate heating/cooling output or cycle timing
• Common symptoms of a failed sensor: erratic operation, incorrect readings, cycles that won't start/finish, or related error codes
• Restores proper control feedback when the original is damaged or out of range

• Disconnect power to the appliance before servicing
• Access the sensor per your service manual; note wire colors/orientation and connector locks before removal
• Transfer any mounting clips or brackets from the original if required
• After installation, run diagnostics or verify resistance/continuity per the tech sheet to confirm proper operation

This electronic control board is the dishwasher's brain, managing cycle logic and communication between the controls and internal sensors. Replacing a failed board can restore responsive controls and consistent, start-to-finish wash performance. What it does:

• Coordinates the dishwasher's operating logic and cycle progression
• Receives inputs from the user interface and door latch and relays commands
• Monitors for faults that trigger beeps or error indications
• Symptoms include no power or no start, unresponsive/intermittent controls, random resets, or stopping mid-cycle

• 1 electronic control board

• Disconnect power at the breaker before service; verify no voltage is present
• Protect the board from static discharge; handle by edges and connector housings
• Document wire/connector positions and transfer them one at a time to the new board
• Access location varies by model (console or base); if your model uses configuration switches/jumpers, match settings to the original per the service sheet

The Motor Mounting Clamp is an OEM part for Frigidaire dryers. This clamp secures the motor in place within the dryer, ensuring it operates smoothly and remains stable during the drying cycles. The motor mounting clamp is essential for maintaining the proper alignment and function of the dryer motor.

Over time, the motor mounting clamp can become worn out or damaged due to constant vibration and movement. Accidental impacts or mishandling during maintenance can also cause the clamp to fail, leading to motor misalignment or instability.

Symptoms of a bad motor mounting clamp include:

• Excessive noise or vibration during the drying cycle
• Motor shifting or moving within the dryer
• Reduced drying efficiency
• The dryer not starting or stopping abruptly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This water inlet valve controls the flow of water into the appliance. When energized, it opens to allow water in and closes to stop flow—restoring proper operation when fills are slow, absent, or water seeps when off.

• Regulates water entering the unit during fill or steam-related cycles
• Common fix for no water or very slow fill
• Can resolve water that drips or leaks from the inlet when the unit is off
• May clear "long fill" or "no water" error/fault indications

• Unplug the appliance and shut off the water supply before servicing
• Place a towel or pan to catch residual water when disconnecting hoses
• Mark hose and wire locations to ensure correct reassembly
• After install, open supply valves, check for leaks, and run a test cycle

This electrical switch controls a specific function within your appliance's circuit. When contacts wear or fail, the unit may not start or selected options won't engage. Replacing the switch restores proper signaling and dependable operation.

• Opens and closes an electrical circuit for its assigned function
• Sends the correct on/off signal to the control or motor circuit
• Common failure symptoms: no start/response, options not engaging, intermittent operation, or related error codes
• Can be checked with a continuity test; replace if contacts are stuck open or closed

• Disconnect power at the breaker; for gas dryers, also shut off gas supply
• Access the switch location and note wire positions (take a reference photo)
• Transfer wires to the new switch one at a time and secure the mounting
• Reassemble and run a test cycle to verify proper operation

This door switch detects whether the appliance door is open or closed. A working switch lets the machine start when the door is fully shut and stops operation when the door opens for safety.

• Monitors door position and allows the cycle to run only when closed
• Interrupts power to stop operation when the door opens
• Common symptoms of a failing switch: appliance won't start with the door closed, must press/hold the door to run, interior light stuck on/off, or a "door open" message on models with a display

• Disconnect power to the appliance before servicing
• Access the switch at the door opening/front panel; release mounting screws or locking tabs and remove the switch
• Move wires to the new switch one at a time to maintain correct positions
• After reassembly, test switch operation before running a cycle

This door lock assembly secures the washer door and signals the control that it's safe to run. Replace it to restore reliable locking and allow cycles to start and spin as designed. What it does:

• Locks and releases the door at the correct points in the cycle
• Sends door-closed status to the main control board
• Prevents the door from opening while the tub is moving
• Common symptoms: cycle won't start, "door open/locked" message, door won't lock or unlock, washer won't spin

• Door lock assembly

• Disconnect power before servicing; internal components can move unexpectedly
• Access the lock behind the front panel/door gasket area; remove the door-boot clamp and mounting screws as needed
• Transfer wiring connectors one at a time to the new lock to maintain correct orientation
• Test door operation and run a quick cycle check before final reassembly

This washer agitator mounts in the tub of top-load models and creates the back-and-forth wash action that moves clothes through water and detergent. Replacing a cracked or loose agitator restores turnover and cleaning performance.

• Produces the oscillating motion that circulates clothes during the wash cycle
• Transfers drive from the shaft/hub to move laundry through water and detergent
• Restores proper load turnover for effective cleaning
• Can help resolve: washer not agitating, weak/slow agitation, poor cleaning, wobbly/noisy agitator, or visible cracks/broken fins

• Disconnect power and turn off water before servicing
• Remove the softener dispenser/cap and center bolt/retainer; lift out the old agitator
• Inspect and transfer any reusable cap or hardware to the new agitator
• Align and seat the new agitator on the drive hub; tighten the fastener per manufacturer guidance and test

The blower housing seal is a perimeter gasket that closes the gap between the blower housing and the adjoining duct or bulkhead. It keeps airflow contained for efficient operation and helps prevent air leaks and debris from escaping.

• Seals the blower housing joint to minimize air leakage
• Helps maintain proper airflow for consistent performance
• Reduces dust/debris escape into the cabinet or surrounding area
• Replaces torn, brittle, flattened, or missing seals that can cause weak air output or rattling

• Disconnect power; turn off gas supply before servicing.
• Access the blower housing; note the original routing/orientation of the seal.
• Remove the old seal and clean mating surfaces of lint and residue.
• Seat the new seal evenly with no gaps or twists; reassemble and verify airflow.

Keep your dryer tumbling smoothly by restoring proper belt tension. This idler spring attaches to the idler arm and maintains tension on the drive belt so the drum turns reliably without slipping or squealing. What it does:

• Applies constant tension to the idler pulley to keep the drive belt tight around the drum and motor
• Helps resolve a drum that won't turn or tumbles intermittently
• Addresses belt issues such as slipping off, appearing loose, or premature breakage from low tension
• Can reduce squealing/chirping from the idler area caused by belt slip

• 1 idler spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the idler assembly by removing the front or lower access panel per your model
• Relieve belt tension, unhook the old spring from the idler arm/frame, and install the new spring in the same orientation and holes
• Rotate the drum by hand to check smooth operation before reassembly

This replacement housing is the body that holds the washer's detergent drawer and channels rinse water through each compartment into the tub. Replacing a cracked or warped housing restores proper dispensing and helps prevent leaks at the dispenser area.

• Supports and aligns the detergent/bleach/softener drawer
• Routes incoming water to flush each compartment into the wash tub
• Interfaces with inlet hoses and outlet chute for proper flow
• Common symptoms: water leaking from the dispenser/front panel, detergent or softener left in the drawer, poor dispensing, drawer difficult to open/close

• Disconnect power and shut off water supply before servicing
• Remove necessary panels/trim, pull out the drawer, and release mounting screws/clips to access the housing
• Label and disconnect hoses; note routing. Transfer any reusable siphon caps, seals, and the drawer from the original housing
• Reassemble, restore water and power, and run a test fill to check for leaks

A replacement mounting screw used to fasten panels and components in compatible Frigidaire appliances. Replacing a missing or damaged screw restores secure fastening, reduces vibration/rattling, and helps keep parts aligned for reliable operation. What it does:

• Secures panels, trim, brackets or small components to prevent movement and rattling
• Replaces missing, stripped, or damaged fasteners that can cause loose or misaligned parts
• Helps maintain proper fit and finish of appliance panels and access covers
• Useful when a loose screw causes vibration noise or minor part movement

• Unplug the appliance or shut off power at the breaker before servicing electrical appliances
• Use the correct screwdriver or bit to match the screw head to avoid stripping
• Start threads by hand, then tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep small parts away from children and retain any removed hardware for reuse

A replacement bracket screw used to fasten internal brackets and panels to the appliance frame, restoring secure mounting and reducing rattling or misalignment caused by stripped, corroded, or missing fasteners. What it does

• Secures mounting brackets, panels or trim to the appliance chassis.
• Restores proper alignment and prevents movement or vibration-related noise.
• Use when the original screw is stripped, rusted, broken, or missing.
• Square-drive head provides a reliable engagement for positive tightening.

• Disconnect power to the appliance before servicing to avoid electrical hazard.
• Use the correct square (Robertson) driver to avoid cam-out and head damage.
• Tighten until snug; avoid over-tightening which can strip threads or crack panels.
• If threads are damaged, replace with the matching screw size and type or repair threads before reuse.

This plug covers an unused opening on the appliance cabinet or panel to restore a clean, finished look. Replacing a missing or damaged plug helps keep dust and lint out of the cabinet and can reduce vibration-related rattles. What it does:

• Covers an open hole on the cabinet or panel after service or manufacturing access
• Helps block dust and lint from entering the cabinet
• Restores appearance and can eliminate small buzzes/rattles from open gaps
• Replaces a lost, cracked, or loose plug

• One plug

• Disconnect power to the appliance; for washers, also turn off the water supply
• Align the plug with the opening and press or snap it in until fully seated and flush
• Before restoring power and use, ensure the plug is secure

This heater baffle mounts near the heating element to deflect and distribute radiant heat. It helps protect nearby surfaces and wiring while promoting more even temperatures and reliable performance inside the appliance.

• Directs and diffuses heat from the element to reduce hot spots
• Acts as a heat shield to protect the liner and adjacent components from direct radiant heat
• Helps maintain proper clearance and airflow around the element
• Damage or a missing baffle can lead to uneven temperatures, localized discoloration/scorching, or a burning smell

• Disconnect power at the breaker or unplug the appliance; allow it to cool completely
• Access the heater area; remove the screws or clips securing the existing baffle and retain the hardware
• Position the new baffle in the same orientation; ensure it does not contact the heating element
• Restore power and test operation

This is a replacement motor-gear assembly kit from Frigidaire. It is designed to work in washer/dryer combo units and is responsible for turning the drum. The motor sits at the bottom of the part. It turns the spindle, and the splines ensure that the drum also turns. The motor assembly is a mechanical part and is subject to physical wear and tear. One common problem is the loss of grease/lubrication from the internal bearings over time. The splines on the spindle may also suffer from wear. When the motor fails, the washer/dryer unit will no longer function, and a replacement will be necessary. To replace the motor-gear assembly, first unplug the appliance. Remove the back to access the motor.This is a genuine OEM part. It's sold individually, and will fit Frigidaire and Electrolux washer/dryer combo units only.