Fftr1814owla Parts

The Power Cord is an OEM replacement part for Frigidaire refrigerators. As the lifeline connecting the appliance to a wall outlet, this cord safely delivers necessary voltage to operate refrigerator systems. 

Potential causes for needing a new power cord include exposure to cuts, abrasions or rodent damage over time in the storage area. Repeated bending stress during installation or removal can also wear out plastic insulation faster.

Symptoms of a faulty power cord include: 

• Refrigerator fails to power on at all
• Flickering lights or inconsistent runs of the compressor  
• Shock, buzzing or humming sounds coming from the cord
• Bare copper wire showing through damaged insulation

This power cord also fits some Electrolux and Gibson refrigerators.

This condenser fan motor drives the fan that cools the condenser coils and compressor. Replacing a weak or noisy motor restores proper heat removal so the refrigerator can reach and maintain set temperatures.

• Rotates the condenser fan to move air across the condenser coils and compressor
• Helps prevent compressor overheating and supports stable cooling performance
• Common symptoms of failure: fan not running, loud noise from the rear bottom, warm refrigerator temperatures, or hot cabinet sides

• Disconnect power and pull the refrigerator away from the wall; remove the lower rear access panel
• Note wire positions; disconnect the harness and remove the old motor
• If reusing existing parts, carefully transfer the fan blade and any mounting hardware; mount the new motor securely
• Ensure the blade spins freely with proper clearance; reinstall the cover and restore power to confirm the fan runs with the compressor

This black center hinge bracket mounts to the cabinet at the middle door position to support and align the refrigerator door. Replacing a bent or worn bracket restores smooth door swing and a dependable gasket seal.

• Mounts the center hinge assembly to the cabinet for stable door support
• Provides the pivot point for the door via the hinge pin/cam hardware
• Helps keep the door aligned so the gasket seals properly
• Common symptoms: sagging or rubbing door, door not closing/sealing, popping open, or hinge-area squeaks/scrapes

• Disconnect power and support the door; remove items from the door to reduce weight
• Remove center hinge cover and screws; lift door off the hinge
• Transfer reusable hardware to the new bracket
• Reinstall bracket and door, then check door alignment and gasket seal

This plug covers the small factory test opening on an appliance cabinet or liner. Replacing a missing or damaged plug helps close the opening to maintain a better seal and restore a clean, finished appearance.

• Seals the factory test opening in the cabinet/panel
• Helps limit air and moisture infiltration through the hole
• Reduces condensation or frost forming around the opening
• Restores a finished look when the original cap is missing or damaged

• Disconnect power before servicing the appliance
• Clean and dry the opening area for proper fit
• Align and press the plug in by hand until it sits flush—do not force or enlarge the hole
• Avoid sharp tools or sealants that could damage the liner or insulation

This door stop limits the opening range of your refrigerator door to prevent overextension and hinge strain. Replace a worn or broken stop to restore controlled door movement and protect surrounding cabinetry from accidental impacts. What it does:

• Controls how far the door opens to prevent overextension and damage
• Helps maintain proper door alignment and reduces stress on the hinges
• Replaces cracked, deformed, or missing stops that no longer hold the door at its stop point
• Common symptoms include the door swinging too far, a hard "clunk" at full open, or visible damage to the stop

• 1 door stop

• Disconnect power; turn off water supply if your unit has a dispenser/ice maker
• Support the door before loosening any hinge fasteners to access the stop
• Note the stop's orientation and position; transfer any spacers and reinstall the same way
• Open and close the door to verify proper range and clearance before fully tightening fasteners

Color: White

This PTC compressor start relay briefly powers the compressor's start winding to get the motor turning, then drops out as it warms. Replacing a weak relay can restore consistent compressor starts and stabilize refrigerator and freezer temperatures.

• Momentarily energizes the compressor's start winding; disengages automatically as the PTC element heats
• Helps protect the compressor by removing the start winding after startup
• Symptoms of failure can include compressor clicking but not running
• Intermittent cooling or warming temperatures between cycles
• Heat discoloration or a burnt odor around the start device

• Disconnect power and remove the rear lower access panel
• Note wire locations; remove the start device cover/retainer and pull the old relay straight off the compressor pins
• Inspect compressor pins; firmly seat the new relay and reconnect wiring
• Reinstall covers/panels, restore power, and verify normal compressor start

This compressor mounting clip secures the compressor to its chassis to reduce movement and noise for reliable operation. It replaces worn or broken clips that allow the compressor to shift during use. What it does:

• Holds the compressor in place on the mounting bracket to prevent shifting
• Reduces vibration and rattling noises caused by a loose mount
• Helps maintain proper compressor alignment for steady operation
• Useful when a cracked or bent clip no longer secures the compressor

• Disconnect power to the appliance before accessing compressor area
• Inspect surrounding mounts and rubber isolators; replace if damaged
• Secure clip fully so compressor is held without forcing or misaligning components

Color: White

This compressor start relay (PTC) briefly powers the compressor's start winding to ensure reliable start-up. Replacing a failed relay can stop repeated clicking and help a non-starting compressor restore normal refrigerator cooling.

• Provides a timed, resistance-based boost to the compressor's start winding, then drops out of the circuit
• Common symptoms: compressor hums then clicks off, frequent clicking from the rear, warm fridge/freezer, intermittent cooling
• Mounts directly on the compressor terminals; works with the separate overload protector and, if equipped, a run capacitor
• Visible signs of failure may include heat damage, burnt odor, or loose/rattling pieces inside the old relay

• Unplug the refrigerator and remove the lower rear access panel to reach the compressor
• Note wire routing and orientation; transfer any harness/retainer and seat the relay fully on the compressor pins
• If a run capacitor is present, discharge it before handling and reconnect to the same terminals
• Inspect the overload and connectors; replace any heat-damaged components

This condenser fan motor powers the refrigerator condenser fan to move air across the condenser coils, helping the appliance cool efficiently. Replaces a failed motor to restore proper condenser airflow and reduce overheating risk. What it does:

• Turns the condenser fan blade to circulate air over condenser coils
• Helps maintain correct operating temperature for the compressor and refrigerant
• Commonly used when the fan is noisy, not spinning, or the compressor overheats
• Works as the main motor for the condenser fan assembly in the cooling system

• Disconnect power to the appliance before starting any repair
• Handle the fan blade and motor mounting carefully to avoid bending blades or damaging wiring
• Test operation after installation;

This refrigerator deflector is a molded guide that mounts inside the unit to direct internal airflow where it's needed. Replacing a cracked, warped, or missing deflector helps restore proper circulation for more consistent temperatures and performance.

• Channels airflow within the freezer/dispenser path to maintain even cooling
• Helps reduce frost or ice buildup caused by misdirected air
• Can address symptoms like warm spots, frost around vents, or rattling from loose parts
• Replace if broken, deformed, or missing

• Disconnect power before servicing
• Remove shelves/panels as needed to access the mounting location; keep track of screws/clips
• Install the new deflector in the same orientation; reuse existing hardware
• Reassemble and verify that vents/air passages are unobstructed

This seal kit replaces worn sealing material in your appliance to restore a tight, reliable barrier. A fresh seal helps stop leaks and drafts, reduces noise, and supports proper temperature and moisture control.

• Creates a secure seal between mating surfaces or components
• Helps prevent air or water leaks around the sealed area
• Can reduce vibration noise from gaps or loose fits
• Supports stable temperatures and overall efficiency
• Common signs include visible gaps, cracking, flattening, or persistent leakage

• Disconnect power (and water or gas, if applicable) before servicing
• Remove the old seal and thoroughly clean mating surfaces of residue
• Test-fit for length/orientation; trim only if instructed by the manufacturer
• Press into place evenly; if adhesive-backed or cement is used, allow proper set time before use and check for leaks

The Hinge Spacer fits between the refrigerator door and hinge pin to set door height and reduce friction. Replacing a worn or missing spacer restores smooth door movement and proper alignment for a reliable seal. What it does:

• Creates a low-friction bearing surface between the hinge and door
• Helps set and maintain correct door height and gap on the hinge pin
• Can reduce squeaks and prevent rubbing or poor closing caused by a worn/missing spacer
• Replace if cracked, deformed, worn flat, or lost during service

• 1 hinge spacer

• Disconnect power and support the door before servicing hinge components
• Remove hinge cover and fasteners; lift the door off the hinge pin per your model's instructions
• Install the spacer on the hinge pin or into the hinge as oriented for your model
• Reinstall and align the door; verify even gasket contact all around

This drain trough directs defrost water from the evaporator to the refrigerator drain, helping prevent pooling, leaks and ice build-up in the fresh-food compartment. A correct trough keeps defrost water flowing and reduces odors or floor damage. What it does:

• Channels defrost/condensate water from the evaporator to the drain system
• Prevents water pooling under shelves or in the crisper area
• Reduces ice buildup and attendant leaks when the drain path is clear
• Replace if cracked, warped, or if water is collecting where it shouldn't

• Disconnect power to the appliance before servicing
• Remove interior shelves/drawers as needed to access the trough
• Clean the drain channel and clear any debris before installing the new trough
• Make sure the trough is fully seated and aligned so water drains properly; follow OEM fastener/placement points

A wiring harness that routes power and signals between a refrigerator's internal electrical components, helping lights, controls, fans and motors operate correctly. Replacing a damaged harness restores reliable electrical connectivity and reduces risk of intermittent faults. What it does:

• Routes power and signal connections between the control board, lights, motors, sensors and other internal components.
• Common visible issues include frayed insulation, broken or loose connectors, or heat damage at terminals.
• Replacing a faulty harness helps eliminate wiring-related faults that can cause component failures or safety concerns.

• Always disconnect power (unplug appliance or shut off circuit breaker) before inspecting or replacing the harness.
• Match connector shapes and pin counts; route the harness along the original path and avoid tight bends or pinch points.
• Secure with the existing clips or ties; replace damaged clips or protective insulation as needed.