Fgh2366pf Parts

This plug covers the small factory test opening on an appliance cabinet or liner. Replacing a missing or damaged plug helps close the opening to maintain a better seal and restore a clean, finished appearance.

• Seals the factory test opening in the cabinet/panel
• Helps limit air and moisture infiltration through the hole
• Reduces condensation or frost forming around the opening
• Restores a finished look when the original cap is missing or damaged

• Disconnect power before servicing the appliance
• Clean and dry the opening area for proper fit
• Align and press the plug in by hand until it sits flush—do not force or enlarge the hole
• Avoid sharp tools or sealants that could damage the liner or insulation

Color: White

This dispenser actuator is a small internal lever in the refrigerator's door dispenser. It engages the switch/mechanism when you press the paddle, helping restore reliable ice or water dispensing and a firm, responsive feel at the dispenser.

• Transfers dispenser paddle movement to the ice/water switch
• If cracked or worn, ice or water may not dispense when pressed
• Dispenser paddle may feel loose, stick, or require extra force
• Can cause intermittent response at the dispenser

• Unplug the refrigerator and shut off the water supply before servicing
• Remove the dispenser trim/escutcheon and panel as directed by your model's instructions
• Replace the actuator, ensuring proper alignment with the switch and pivot points
• Reassemble, restore power, and test both ice and water dispensing

This door-activated light switch installs in the refrigerator liner and opens or closes the circuit to the interior lamp as the door moves. It restores reliable, automatic on/off lighting when you open and close the door. What it does:

• Controls the interior light based on door position
• Helps fix a light that won't turn on with the door open
• Helps fix a light that stays on when the door is closed
• On some models, also signals door-ajar/dispenser interlock functions

• 1 light/lamp switch

• Disconnect power to the refrigerator before servicing
• The switch is typically in the door jamb; gently release and pull it out, then transfer wires one at a time to the new switch
• Match wire positions/orientation and seat the switch flush to prevent air leaks
• Test door operation and light before finalizing reassembly

This small permanent magnet is used in supported refrigerator assemblies to actuate a mating reed switch or metal keeper. It helps the appliance recognize a closed position or hold a light cover/door closed for proper operation. What it does:

• Works with a reed switch or ferrous keeper to provide position sensing or magnetic latching
• Helps ensure features dependent on closed position operate correctly
• Can resolve issues where a small cover or door won't stay closed
• Address erratic "door ajar" indications tied to magnetic sensing

• Disconnect power and water before servicing
• Note the original magnet's location and orientation; polarity matters for proper operation
• Seat the magnet fully in its pocket or holder and align with the mating switch/keeper
• Test the related function before reassembling panels and trim

This slide assembly mounts inside the refrigerator to support and guide a slide-out shelf or drawer. Replacing a worn or broken slide restores smooth travel, alignment, and easy access to stored items. What it does:

• Provides the track/rail that lets a shelf or drawer slide in and out smoothly
• Helps keep the shelf/pan level and properly aligned
• Can resolve sticking, rough or noisy travel, sagging on one side, or a cracked/broken rail
• Restores full extension and proper seating of the shelf or drawer

• 1 slide assembly

• Unplug the refrigerator and remove contents from the affected shelf/drawer
• Remove the shelf or drawer and retain mounting screws or clips
• Note slide orientation; transfer any reusable stops or clips from the old slide
• Secure the new slide with existing hardware and test for smooth operation

This factory screw secures components inside your refrigerator. Replacing a missing, rusted, or stripped fastener restores a tight, rattle-free fit for shelves, panels, and brackets so everything stays aligned, supported, and quiet.

• Fastens panels, brackets, or trim to the cabinet/liner
• Replaces damaged, corroded, or stripped hardware
• Helps resolve looseness, vibration, rattling, or misalignment
• Maintains proper support for shelves, covers, and assemblies

• Unplug the appliance; if working near water lines, shut off the water supply
• Match the new screw to the original; transfer any washers or spacers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving clip/insert is damaged, replace it to ensure a secure repair

This housing forms the framework of the ice crusher assembly inside the refrigerator's ice bucket. It holds and aligns the auger and crusher components so ice is crushed consistently and dispensed smoothly.

• Supports and positions the auger and crusher blades within the ice bin
• Guides ice through the crusher for consistent flow to the dispenser
• If damaged or worn, can cause: crushed ice not dispensing, cubes only, or jamming
• Can also lead to loud grinding noises or visible cracks/broken tabs in the ice bucket assembly

• Disconnect power before servicing; remove the ice bin from the freezer door
• Empty the bin and allow parts to acclimate to room temperature before disassembly
• Note the order and orientation of internal crusher parts; transfer them to the new housing as needed
• Use caution—crusher components can have sharp edges; ensure proper alignment before reinstallation

This water fill chute kit channels incoming water from the fill tube into the ice maker mold. Replacing a cracked or deformed chute helps stop leaks and ice buildup at the fill area and supports consistent, properly directed fills for reliable ice production.

• Directs water from the inlet/fill tube into the ice maker mold during the fill cycle
• Helps prevent splashing, leaks, and ice accumulation at the fill point
• Replaces damaged, warped, or missing chute/funnel components
• Typical symptoms: water dripping near the ice maker, frost/ice around the fill area, cubes clumping together, intermittent ice production

• Disconnect power and shut off the household water supply before servicing
• Remove the ice bin and access the fill area at the rear/top of the ice maker
• Clear any ice blockage; remove fasteners/clips to take out the old chute; transfer any seals or grommets if present
• Align the new chute with the fill tube and mold, seat fully, secure, then restore water/power and run a test fill to check for leaks

This mullion guide secures and aligns the refrigerator's vertical door trim so doors close evenly and seals engage properly. Replacing a worn or broken guide helps restore door alignment and reduce drafts at the center seam. What it does:

• Holds the mullion/vertical trim in place and keeps the trim flush with the cabinet
• Guides the doors during closing to maintain even gaps and seal contact
• Prevents the mullion from shifting, rattling, or catching when doors open or close
• Common symptom: loose, misaligned, or damaged center trim causing wind, noise, or uneven door gaps

• Disconnect power before starting service and work on a stable surface
• Remove the mullion/trim and any surrounding gaskets or screws as needed to access the guide
• Use appropriate trim/removal tools to avoid damaging adjacent plastic or gasket material
• Reinstall hardware securely and verify doors close and seals engage properly after installation

This replacement magnet is used in select refrigerator assemblies. It provides the magnetic hold or sensor trigger required so doors, flaps, or rails stay closed and so the controls can accurately detect when components are in position.

• Supplies magnetic retention in the specified assembly to keep parts closed and aligned
• Activates magnetic reed sensors in models that use them for door/position detection
• Weak or missing magnets can lead to door-ajar alerts, air leaks, or components not staying shut
• Visible damage or incorrect orientation can cause intermittent operation or improper sealing

• Disconnect power before servicing; turn off water if working near the dispenser
• Use your model's parts diagram to locate the magnet and note its orientation/polarity
• Press-fit into its holder carefully; do not chip or crack the magnet
• Verify proper closure/sensing operation before returning the appliance to service

This slide assembly restores smooth, stable movement to your refrigerator drawer or basket so it opens and closes easily and stays aligned. Replace a worn or cracked slide to eliminate sticking, sagging, or track problems.

• Guides and supports the drawer/basket along the cabinet track
• Maintains alignment to prevent binding, rubbing, or popping off the rail
• Restores full, smooth travel for easier access to contents
• Common symptoms: drawer hard to open/close, sits crooked, falls off track, or makes scraping/clicking noises

• Disconnect power and remove the drawer and contents before starting.
• Note the slide's orientation; remove mounting screws/clips and the old slide.
• Install the new slide in the same position; transfer any snap-on brackets from the original if applicable.
• Reinstall the drawer, ensuring both sides are seated on the tracks, and test for smooth operation.

This condenser fan shroud sits in the rear machine compartment and positions the fan and motor to move air through the condenser coil. A cracked or warped shroud can reduce cooling performance and increase noise or vibration.

• Directs and focuses airflow across the condenser coil and compressor to remove heat
• Holds the condenser fan motor and blade in proper alignment
• Helps maintain stable refrigerator/freezer temperatures and efficient operation
• When damaged, may cause weak airflow, warmer temps, vibration, or fan scraping/rubbing noises at the back of the unit

• Unplug the refrigerator and wear cut-resistant gloves
• Pull the unit forward and remove the lower rear access panel to reach the machine compartment
• Take a photo of fan/motor orientation; transfer components to the new shroud and reuse existing hardware
• Confirm blade spins freely with proper clearance before restoring power

This bushing is a small bearing insert that supports a pin or shaft within an appliance mechanism. Replacing a worn bushing restores smooth movement and helps prevent accelerated wear, scraping, and noise in the affected assembly.

• Provides a low-friction surface for pivoting or sliding components
• Helps correct loose, wobbly, or uneven movement
• Can reduce squeaking, scraping, or binding during operation
• Replaces cracked, distorted, or missing bushings to maintain alignment

• Disconnect power and, if applicable, shut off the water supply before servicing
• Note the original bushing's orientation and depth; seat the replacement fully in the same position
• Inspect the mating pin/shaft and surrounding bracket/hinge for wear; replace any damaged parts
• Do not overtighten fasteners through plastic and avoid lubricants unless specified by the manufacturer

This upper hinge cover fits the left-hand side and snaps over the top door hinge in a gray finish. It protects the hinge hardware and restores a clean, finished look when the original cover is cracked or missing.

• Conceals upper hinge hardware on the left side for a clean appearance
• Shields the hinge area from dust and minor spills
• Helps prevent snagging or damage to wires routed through the hinge area on some models
• Typical symptoms: broken, loose, or missing hinge cover

• Disconnect power to the appliance before servicing
• Remove any retaining screw(s) or release tabs from the old cover; keep original fasteners for reuse
• Align the new cover over the hinge and snap or secure into place
• Support the door before loosening fasteners

This spacer is a small positioning piece used in refrigerator assemblies to maintain proper clearance and alignment between parts. Replacing a worn or missing spacer helps restore smooth operation and prevents rubbing or binding. What it does:

• Maintains the designed gap between mating parts to prevent friction and wear
• Helps keep assemblies aligned for smooth, consistent movement
• Reduces looseness, rattling, or poor fit caused by a missing or deformed spacer
• Typical signs include visible damage or a missing spacer and misalignment or scraping noises in the area it installs

• 1 spacer

• Disconnect power; if working near water components, shut off the water supply
• Use your model's parts diagram to determine exact location and orientation
• Retain and reuse original fasteners or clips unless damaged
• Do not overtighten hardware; ensure smooth operation after installation