Frigidaire Ffus2613ls4 Parts

This hinge bearing supports the freezer door on the hinge pin so it swings smoothly and stays aligned. Replacing a worn bearing can stop scraping or sagging and help restore proper door movement and sealing.

• Provides a low-friction surface between the hinge pin and door
• Helps maintain correct door height and alignment for a reliable seal
• Wear symptoms include squeaking/scraping, door drop or wobble, and difficulty closing
• Replace if the original bearing is cracked, flattened, or missing

• Disconnect power and remove items from the freezer door before starting
• Support the door; remove hinge cover and fasteners, then lift the door off the hinge pin
• Slide the old bearing off the hinge pin and install the new bearing in the same orientation
• Reassemble, then check door alignment and gasket contact; adjust as needed

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle

This humidity control is the adjustable slider in the crisper drawer cover that opens and closes the vent to regulate moisture around fruits and vegetables. Replace a cracked or missing control to restore smooth adjustment and consistent crisper conditions.

• Mounts to the crisper cover and links to the vent/damper door
• Slides between settings to increase or reduce airflow for proper crisper humidity
• Typical symptoms: broken or missing lever, slider stuck or loose, vent doesn't move as you adjust, excess condensation or wilting produce

• Disconnect power; remove food, crisper pan, and cover/glass as needed—handle glass carefully
• Release the old control from its slot/retainer and note the vent linkage orientation
• Seat the new control and engage the linkage; confirm full travel and proper vent action
• Reassemble the cover and drawer, then restore power

Specs: Hex head ,1/4-20 x 5/8

This drive cam is the rotating plastic cam used in the refrigerator's ice system. It transfers the motor's motion to linked parts to advance the cycle so ice can be produced and dispensed smoothly.

• Transfers rotation from the motor to move internal levers/gears in the ice assembly
• Advances the ice-making/dispensing cycle
• Wear or cracks can cause stalling, clicking/grinding, or no/weak ice dispensing
• May lead to ice not ejecting or jamming mid-cycle

• Disconnect power and shut off water before servicing
• Remove the ice bin; access the ice maker or dispenser mechanism as your model requires
• Note the cam's orientation and alignment marks; seat the new cam fully on the shaft
• Reassemble, restore power, and run a test cycle to confirm operation

This replacement ice container front is the front cover for the freezer's ice bucket. It restores a secure front wall so cubes stay contained and the bucket seats and dispenses correctly. What it does:

• Forms the front face of the ice container to keep ice contained
• Helps the bucket fit and align for proper dispensing
• Replaces a cracked, broken, loose, or missing front panel
• May help if ice spills from the bin or the bucket won't slide in or latch properly

• 1 ice container front (front cover only)

• Unplug the refrigerator and remove the ice bucket from the freezer
• Empty the bucket; transfer any screws, clips, or labels from the old front to the new part
• Align tabs and snap/fasten the new front to the bucket; do not overtighten screws
• Reinstall the bucket and check seating and dispenser operation

The Thermistor is an OEM Replacement Part that maintains the temperature inside your Frigidaire refrigerator. This thermistor handles reading the internal temperature. After reading, it transmits this information to the control system. At a temperature of 29 degrees, the thermistor should exhibit a resistance of about 35k ohms. While at room temperature, it should read approximately 5k ohms.

Causes of a bad thermistor can include regular wear and tear, exposure to moisture, or electrical issues. Over time, the thermistor may become less accurate or stop working altogether.

Symptoms of a bad thermistor include:

• Inconsistent or incorrect temperature readings
• The refrigerator being too warm or too cold
• The cooling system running continuously or not at all
• Error codes related to temperature control

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This hinge bracket supports and aligns the refrigerator door at the pivot point, helping the door open and close smoothly and seal properly. Replacing a worn bracket can restore stable door movement and reduce air leaks.

• Provides rigid support for the door hinge to maintain proper alignment
• Helps ensure a consistent door seal to prevent temperature fluctuations
• Common fix for loose, sagging, or misaligned doors
• Helps if the door makes popping/grinding noises when opening or closing

• Unplug the refrigerator and wear cut-resistant gloves
• Support the door before removing hinge fasteners to prevent drops
• Transfer and reinstall existing screws/hinge pin as needed
• Check door alignment and gasket contact after installation

This refrigerator switch board provides the electrical switching and terminal connection interface for a control circuit. Replacing a worn board restores reliable activation of the related function and helps eliminate intermittent response from fatigued contacts or heat-damaged terminals.

• Houses the switch contacts and connection terminals on a compact PCB
• Converts actuator movement into a clean electrical on/off signal
• Routes power/signal to the appropriate component within the circuit
• Common symptoms: unresponsive or intermittent operation, needing extra force to activate, stuck on/off behavior, or visibly burnt/loose terminals
• Match the "terminal beta" variant to your original to ensure connector compatibility

• Disconnect power before servicing; use proper ESD precautions and handle the board by its edges
• Photograph and label all wire locations; move connections one at a time to the new board
• Transfer any brackets, levers, or screws from the original assembly as required
• Do not overtighten mounting screws to avoid PCB damage

This water filter housing secures and seals the refrigerator's filter cartridge, routing water to the dispenser and ice maker. Replace it if the filter area leaks, the filter won't seat, or water/ice flow is reduced. What it does:

• Holds and seals the filter cartridge to the water system
• Directs water through the filter to the dispenser and ice maker
• Helps maintain proper pressure and a leak-resistant connection at the filter head
• Typical symptoms: leaking at the filter area, slow/no water from the dispenser, no ice production, filter won't lock in place

• 1 water filter housing assembly

• Disconnect power and shut off the water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Note tube routing; use the quick-connect collets to release/insert water lines fully
• Restore water and power, check all connections for leaks, and flush the dispenser to clear air

This module cover label restores clear, readable control markings on your appliance's module cover. Replace a worn or missing label to keep settings easy to identify and maintain a clean, factory look. What it does:

• Restores readable control text/icons on the module cover
• Replaces a faded, peeling, or damaged overlay
• Helps prevent mis-selection due to illegible markings
• Refreshes overall appearance

• One module cover label

• Disconnect power before servicing to prevent accidental operation.
• Access the module cover; remove it if your model requires.
• Clean and fully dry the application surface; confirm orientation.
• Align carefully, apply from one edge, and press evenly to seat the label; reassemble and restore power.

This is a factory replacement screw fastener used to secure components in your appliance. It restores a tight, rattle-free fit for panels, brackets, and trim when an original screw is missing, stripped, or corroded.

• Secures panels, brackets, and trim to the appliance cabinet or liner
• Replaces a missing, stripped, or rusty screw
• Helps eliminate looseness, vibration, or rattling components
• Maintains proper alignment and a clean, factory fit

• Unplug the appliance before servicing; if near water lines, shut off the supply
• Match to the original and install in the same location/orientation
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic
• Keep and reuse any original washers or spacers if present

Shroud assembly that covers internal refrigerator components and helps direct airflow for consistent cooling. Replacing a cracked or damaged shroud restores proper airflow paths and can reduce fan vibration and contact-related noise. What it does:

• Covers and protects internal components from debris and accidental contact.
• Directs airflow around the evaporator/fan area to support even cooling; symptoms of a failing shroud include uneven cooling or frost buildup.
• Reduces fan noise and vibration when mounting tabs or the housing are intact.
• Visible cracks, broken tabs, or holes are common signs the shroud needs replacement.

• Always disconnect power to the appliance before beginning any repair.
• Remove interior panels and fasteners carefully; retain hardware for reinstallation.
• Align tabs and mounting points; do not force broken tabs—replace damaged fasteners as needed.

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

Access door provides a finished cover for the appliance's service opening, protecting internal components from dust and damage while keeping the unit looking tidy and allowing access for maintenance and repairs. What it does:

• Covers the service or access opening and protects wiring, valves, and other internal parts.
• Allows access to controls, connections, or components for inspection and repair without removing major panels.
• Helps prevent debris, pets, or fingers from contacting internal parts.
• Replace a missing, cracked, or damaged access door to restore appearance and reduce exposure of internal components.

• Always disconnect power (and gas for gas appliances) before removing panels or working on the appliance.
• Handle the door and surrounding edges carefully to avoid cuts; keep original fasteners and reuse if undamaged.
• Align tabs/clips and secure with manufacturer screws; do not overtighten.

This refrigerator seal restores a tight barrier between internal components. Replacing a worn or damaged seal helps prevent air leaks and moisture intrusion, supporting proper airflow, stable temperatures, and reduced frost or condensation around the joint.

• Creates an air-tight barrier between mating surfaces
• Helps maintain correct airflow and temperature balance between compartments
• Reduces frost, condensation, and warm/cold spots near the sealed area
• Common signs of failure: visible gaps, loose/crumbled seal, rattling panel, moisture or frost at the joint

• Disconnect power before servicing
• Remove the related cover or housing to access the old seal
• Clean contact surfaces; install the new seal in the same orientation without stretching or pinching
• Reassemble and verify an even seal and normal airflow before returning to service