Frigidaire Flse60rgs1 Parts

I replaced the motor. It was time consuming because you have to take all of the parts that attach off. Was fairy simple. Pleased about the parts delivery. Ordered and received the next day. Read more

I took the easy fix first and replaced the Capacitor. That got me three loads before the motor burned out. I ordered the motor from AppliancePartsPros.com after a google search for "best price model # 134159500 Drive motor " The part arrived in 5 days, and it took about 15 minutes to remove the old motor and replace it with the new one. Simple and easy. four screws, four nuts, and two electrical connections. — The hardest step was one of the four mounting screws was way back inside and it took... Read more

Ordered a new handle from appliancepartspros.com and installed. Read more

• Doesn't shut off
• Timer will not advance

With a Phillips screw driver, on the back of the control panel there was about 6 or 7 screws to undo, to take the cover off and 2 screws holding the timer in place. Just undone those, took out old timer, made sure I took wires from old timer one at a time, and, put on new timer. Put everything back, although I had to find a couple of very small washers to make the timer fit tight, in the 2 holes it came out of. Luckily I had those or would of been a very loose timer. Very easy to do. Read more

Simply open the top of the washer by inserting a putty knife (watch YouTube ) and then the front panel by removing two bottom philips head screws on the front. The whole front panel comes right off. Using pliers the spring clams holding each hose, they come off and each hose is replaced. The drain one was only leaking but since it has open I changed both and even the drive belt. Whole job less than 1 hour. BTW parts arrived next day! Read more

The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more

I tore into the washer until i found what i thought was the problem which was the upper outer tub splash cover gasket and when i couldnt find one in my town i ordered a new one from u folks and replaced it hoping for the best and was successful. This fix costed me $35 instead of the $400+ for a new washer glad i looked into it instead of discarding it and buying a new one as most may do thanks Read more

The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more

Watched a few of your videos and ordered the springs and a insert, and actually got the parts right. I am not a Appliance repair guy but I am retired and I am pretty handy so I thought what the heck. I watched the videos, a lot of common sense, common tools, and plenty of time. My knuckles are busted up and a little blood, but I got it done. Was actually kind of rewarding. Works like a champ. The Videos, ARE AWESOME. Read more

Old, unused stack set. Washer was great, dryer was grinding. Started with the mounting bracket/bearing and the belt. The old ones were slightly beatup. Put it back together and the problem persisted. Found the real problem when I pulled apart the blower to get to the motor. The fan had broken fins that had jammed in the side of the blower housing, and the friction had melted through the outer wall of the fan. Got the blower housing from APP, got the fan from a competitors for $30 less. When it... Read more

Yes Read more

The repair guy told me if I have him fix it I should just buy a new one. I like my washer and dryer because it's a combo and takes up little space so I decided to fix it myself. Not sure if I got lucky but appliance parts pros had a video with almost my exact washer which made repair very easy. Read more

It was easier than I imagined! I watched a video on youtube...I wish they would put up fixit videos on this site. There isn't much to a dryer...:-> Read more

Read your terms & conditions thanks for having parts available Read more

Align plug and snap into place. Read more