Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This middle spray arm assembly mounts at the center wash level and distributes pressurized water across both racks. Replacing a damaged or clogged arm restores even spray coverage and helps resolve weak cleaning performance, especially on the upper rack.
Replaced Middle Spray Arm Hub and Arm Spray Middle Asm. Works like a charm now. Read more
Remove the unit. Unscrewed filler cup. Put on new part. FIXED PROBLEM. Read more
I found the schematics on your site and took my best guess at the individual components that I should replace, related to the flood switch. I guessed correctly. Read more
This was not an obvious source of a leak. The Tower Heater Assembly Nut developed a crack over time due to heat exposure. So the leak was gradual slowly getting worse over time. It was a hairline crack that ran down one of the edges of the nut making it hard to see. In talking to a pro he said it isn't a common problem. It is all the way in the back of the bottom of the dishwasher so it is not something you can see without pulling the dishwasher out and running it. The repair itself is easy. I... Read more
This turbidity sensor monitors wash water clarity so the machine can adjust wash cycles and rinse times for cleaner results and efficient water use. It replaces a failed or inconsistent turbidity reading to restore proper load sensing. What it does:
I used lime away, vinegar, finish washer cleaner none of them worked. Finally just use Brillo on the entire cabinet interior. It came out very clean. Only needed very light scrubbing. Then replaced the severely corroded filters Riser tube and upper jet which was not turning. After this the upper arm turned perfectly silverware and glassware and silverware came out rinse very clean. Will do preventative maintenance in the future. Dishwasher was about 5 years old GE Profile high-end Read more
GE washing machine did not start and one of the possible problems was the door latch. I opened the front panel and found out that the door latch electrical connection was rusted and damaged due to likely water drips thru the latch hole on the door. Took to damaged latch out and replaced the wire connection with new spade plugs. Got the new parts in 2 days and the dishwasher started right up after installation. Read more
This mid spray arm assembly delivers targeted spray to the dishwasher's middle rack so dishes get an even clean. Replaces a cracked, broken or clogged mid-arm to restore proper water distribution and cleaning performance. What it does
Found a service manual that is close enough to my GE dishwasher. Service Manual for GE Dishwasher-EDW4000 was found on the following webpage. http://www.applianceaid.com/pdf/serv-man-EDW4000.pdf Gives enough information to test out the dishwasher. Read it, check out Factory Test Mode. GE should have given this out as a normal User Manual. The usual user manual lack anything to help troubleshoot a problem. Read more
This is a genuine OEM replacement lower spray arm bearing sourced directly from the manufacturer for use in dishwashers. The lower spray arm spins to distribute water to the dishes during the wash cycle. Thus spray arm bearing supports the spray arm and lessens the friction, which allows it to spin more easily. If the dishes are not clean after the wash and rinse cycle, or the arm is making loud noises, the spin arm bearing may need to be replaced. This bearing is a small metal part that may wear over time. If the bearing is distorted or damaged, the arm will not sit level, and spinning may be very loud, or it may not spin. The spray arm bearing should be replaced. Turn off the breaker or disconnect the power to the dishwasher. Open the dishwasher and pull the bottom rack out. Turn the lower spray arm counterclockwise to remove it. Use a telescoping magnet to pull the bearing up from the hole in the middle. Install the new bearing and reinstall the spray arm. Put the dishrack back inside and reconnect the power.This lower spray arm bearing is a gray metal part that is sold individually. It is designed for use in dishwashers designed by General Electric and Hotpoint.
The main conduit was broken and the pump connector had a hole in it. The pump also was showing signs of leaking. I completely disassembled the dishwasher cleaned everything and reassembled. The repair videos are a big help. Thank you. Read more
Replaced all of the broken parts with the new parts from Appliance Parts Pros. Read more