Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Left apron bracket for washers. Secures the apron panel to the washer cabinet. Replace if cracked, broken, or missing to restore proper panel support.
Usually ships within 4 - 14 days
Right side apron bracket for washers. Secures the apron panel to the washer cabinet. Replace if cracked, bent, or broken to restore proper panel support.
Washer leg and platform assembly that supports and levels your washer. Replace if the leg is cracked, broken, or the platform is damaged or missing.
This 1/4-20 screw secures the leg and platform assembly in your top-load washer. Replace missing or loose screws to restore proper balance.
OK kids, pay attention! This was my second attempt @ this repair. My first repair started leaking right away and had to be re-done about 6 months later. HERE IS THE PROBLEM!. In the video, you'll notice that (while putting it back together) when you put the square hole washer and split-ring over the shaft, they look to land atop the rubber seal, buy when you do this in real life, there is a gap between the seal and the washer. (This gap was close to a 1/4 inch). I THINK that the first time I... Read more
Replacement end cap for washer left-side assembly. Secures cabinet alignment and protects internal components. Needed when original is cracked or missing.
Self-leveling bracket for top-load washers. Mounts to the base to stabilize the unit. Replace if broken, bent, or missing to restore proper leveling.
Converts older 3-piece washer support apron to one-piece design. Replaces sagging, bent, or broken apron brackets that cause motor clearance issues.
Following the video instruction. Very easy used putty knife,needle nose plyers and a electric drill driver to remove the sheet metal screws/nuts. Read more
Replacement plug insert for washer control panels and cabinet surfaces. Snaps into pre-drilled holes to cover openings or secure components. Needed when original plug is missing, cracked, or broken.
Conduit hose for top-load washers. Protects wiring connections inside the cabinet. Replace if cracked, split, or damaged to restore proper coverage.
Protective conduit sleeve for washer electrical wiring. Installs between control panel and base. Replace if cracked, worn, or missing to protect wires.
Water intake hose assembly for washers. Connects water supply to inlet valve. Replace if cracked, leaking, worn, or damaged to restore proper water flow.
Base assembly for washers. Installs at the bottom of the cabinet to support the machine. Replace if cracked, damaged, or structurally compromised.
This tub-bearing split ring is an OEM replacement part designed for GE washing machines. This part measures 2 inches in diameter. It is positioned between the inner and outer tubs to hold the tub bearing inside the outer tub. The Tub Bearing Split Ring not only supports the tub/hub assembly but also ensures smooth operation.
Symptoms of a bad Tub Bearing Split Ring include:
Causes can be extended use over time which leads to wear and fatigue of the split ring material. Cracks or breaks can develop, reducing its stability and load-bearing capacity.
This genuine GE replacement part is also compatible with Hotpoint, RCA and some Kenmore front-load models.
NOTE: For the washer outer tub seal order WH02X10383.
I had never worked on a washing machine before but after watching the online videos I felt like I could do the repair. I was almost positive it was the Mode Shifter and Shaft Assembly that was bad. I could hear the bearing making a grinding noise when I turned the tub by hand. I ordered the part I needed plus additional parts that could be an issue later such as a drive belt, tub bearing, tub seal, tub nut, split ring, etc; Preventive maintenance that would keep from having to tear it all... Read more
The Knob Clip is an OEM part for GE washing machines and dryers. This small but crucial component is designed to secure the control knob to the appliance's control panel.
Over time, knob clips can wear out or break due to frequent use or accidental damage. When this happens, the control knob may become loose, fall off easily, or fail to engage the control panel properly, making it difficult to set the appliance to the desired cycle or function.
Symptoms of a bad Knob Clip include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
I actually called a repair service in our area. The serviceman asked questions and detected that I didn't need a timer unit but thought it was just a knob that was required. He offered to come out but the expense would be considerable. I am SO relieved that it was indeed the knob, and the dryer was fixed. In this time in our lives, every penny counts. I must applaud the serviceman for his honesty and dedication to his trade. He directed me to this website, but also added if there were any... Read more
The Agitator Assembly is an OEM part for GE washing machines. This part moves clothes through the water and detergent during the wash cycle. This part ensures thorough cleaning by creating the necessary motion to distribute and cleanse laundry evenly.
Causes of a bad Agitator Assembly can range from wear and tear over extended use, to damage from overloading the washing machine, or even issues with the drive mechanism that powers the agitator's motion.
Symptoms of a bad Agitator Assembly include:
Replaced the broken agitator on my GE washer & couplin. Took a flat rope placed under the old agitator and with a stern jerk it popped off. Then a 7/16 socket set with a long extension took the bolt lose, and removed the couplin. Replaced the new couplin, with the new bolt tighten. Slide the new agitator into place with a stern push it snapped in place. Works perfectly. Thank you for the fast shipping. Read more
The Washer Top is an OEM part for GE washers. It is the upper panel that covers the internal components of the washing machine and provides a flat surface for loading and unloading laundry.
Causes of a bad Washer Top can include physical impact, warping due to prolonged exposure to heat or moisture, or general wear and tear over time.
Symptoms of a bad Washer Top include:
I bought and replaced the top and the lid for the washer. The washer now looks like a brand new washer even though it’s 12 years old. Total repair took less than an hour. Read more