Need Help?
Call or text
Replacement slide-out shelf for refrigerator interior storage. Installs in main compartment. Replace if cracked, broken, or warped. Slides for access.
Bought a new panel and installed it. It was simple 3 plugs and done. Read more
Bushing that lines the upper hinge pin on refrigerator doors. Replace if cracked, worn, or missing to restore smooth door swing and proper alignment.
Replaced upper and lower thimble's, lever arm, cam closure. Door stop was not the problem, but ordered it and replaced it too. The door of course has to come off, remove the top hinge, and lift it away. Lubricated moving parts with silicone spray. Be sure and put the door back in the open position, so the lever arm and cam closure can properly interact, then close the door. Remove the plastic grate at the bottom to get at the lever arm. Presto. Problem gone. Don't put excessive weight... Read more
Ice dispenser stuck on crushed or not dispensing? This armature kit connects the solenoid to the chute door. Moderate DIY repair with video guide.
Replaced the water supply valve...boom! Read more
Replaces the damaged or missing edge trim on your freezer shelf. Snaps onto the shelf frame to provide a finished lip and restore its original appearance.
Replaced with new parts. Read more
Fix a light that won't turn on or flickers in your refrigerator. This E12 socket replacement is straightforward with our step-by-step video guide.
When diagnosing the problem, I discovered that the ice door was not properly sealing and that the solenoid had appeared to rust/corrode forcing the door open. I replaced most of the ice dispenser internals (solenoid, crank, door, and spring) following the video. The door will now open when dispensing ice (which it does!), and will oddly stay open for a few seconds once I am finished, but does seal properly and the chute/container no longer frosts over. Read more
Refrigerator not cooling or compressor clicking on and off? This compressor kit restores cooling. Requires certified technician with specialty tools.
Ice won't dispense or drive spins freely? This auger drive coupler connects the motor to the ice bucket. Moderately difficult repair with basic tools.
The auger in ice bucket was frozen and locked in place (some how liquid water must have spilled inside and froze the shaft and bushing). When the motor was activated to deliver ice, the jam caused the motor shaft to strip the threads. With the threads stripped, there is no way (that I could find) to get the drive auger off of the shaft (btw, it is left-hand threaded). Apparently the Drive Auger is made of stainless steel - a harder metal then the motor shaft. To repair it, I removed the... Read more
Protects the freezer light bulb from damage while maintaining visibility. Replace if cracked, yellowed, or broken. Confirm fit with your model number.
Replace solenoid, flapper door and recess spring. Really only needed solenoid, but other parts were so inexpensive and I knew I would already be in there. Read more
Plastic water line that runs from the water valve to the icemaker fill tube. Replace if cracked, brittle, broken, or leaking at connection points.
Thanks to the AppliancePartsPro, I ordered it online and received it quickly. I even used the step by step directions on how to replace the tube from the AppliancePartsPro website. Just be very careful and review the instructions first. Couple of important things: 1. Take a picture of the existing wiring and tubes before you take them apart. 2. *if* you remove the wires ( red and white plugs) from the valve, make sure you plug them back in correctly. 3. Do not pull or push the tubes hard. Use... Read more
Secures the ice chute flapper in your refrigerator door. Replace if cracked or missing to restore proper sealing and prevent frost buildup. Verify fit.
Replaced springs, flapper assembly and ice door retainer as described in videos and it was easy. So far so good..water dispenses. Read more
Fixed-position freezer shelf for side-by-side refrigerators. Replace cracked, broken, or missing shelves to restore storage capacity and organization.
Replacement top hinge pin for refrigerator doors. Provides the upper pivot point for smooth door swing and proper alignment. Replace if bent or worn.
Replaced the hinges and all parts pertaining to hinges on the refrigerator door. Total cost was approx. $83 and it took 1 hour this morning (Saturday). Now the door is closing tightly. The refrigerator is 10 years old. GE brand. Read more
Upper hinge pivot pin for side-by-side refrigerator freezer doors. Replace if bent, worn, or missing to restore proper door alignment and swing.
By using my socket set Read more
Black plastic funnel extension attaches to the front of your refrigerator's ice dispenser. Replace if cracked, broken, or missing to reduce splashing.
I ordered the ice door assembly and a door recess spring and while I was working on that particular area the ice chute funnel that kept falling off on one side. It was all very easy, took maybe 15 mins in all. I watched the "how to" video that was posted and it was extremely helpful, giving me to confidence to do this myself. The only thing I might do different another time would be to take a look at the assembly before ordering parts. I didn't as I didn't want to keep opening the area up... Read more
Replacement mounting screw for refrigerator panels, brackets, door handles, and trim. Needed when original hardware is missing, stripped, or corroded.
Black bottom door hinge and pin assembly for side-by-side refrigerators. Replace this load-bearing pivot component if cracked, broken, or worn out.
I replaced the lever asm. and spring Read more