Gfe28jelfds Parts

Replacement grille thermistor. This temperature sensor monitors air at the grille location and relays the signal to the control so cooling and defrost responses stay consistent and food stays within target temperatures.

• Senses ambient air temperature at the grille and varies resistance with temperature
• Sends data to the control to help regulate compressor/fan run time and defrost intervals
• Aids in maintaining stable refrigerator and freezer temperatures
• A failing sensor may lead to temperature swings, extended run time, or irregular defrosting

• Disconnect power before servicing
• Remove the grille/kickplate to access the sensor and its connector
• Disconnect the old sensor, install the new one, and route wiring as originally; ensure the sensor is fully seated and wires aren't pinched
• Restore power and allow up to 24 hours for temperatures to stabilize

Port Gasket forms a watertight seal around the refrigerator dispenser port to prevent leaks and moisture intrusion. Installing a fresh gasket restores proper sealing and helps stop dispenser drips and water pooling. What it does:

• Seals the dispenser/port opening to prevent water from leaking at the door area.
• Helps stop visible dripping or pooling near the dispenser and reduces moisture buildup.
• Replaces worn, cracked, flattened, or missing gaskets that allow leaks or drafts.
• Restores a proper seal so the dispenser operates without water escaping around the port.

• Disconnect power (and shut off the water supply if working near the dispenser) before beginning work.
• Remove the old gasket and thoroughly clean mating surfaces to ensure a full seal.
• Press the new gasket evenly into the port opening, making sure it seats all the way around.
• After installation, restore power/water and run a small dispense test to confirm no leaks.

This replacement power cord provides the appliance's main AC connection so it can receive power and operate reliably. It restores a safe, factory-style power connection when the original cord is damaged or worn. What it does

• Supplies mains power to the appliance through the cabinet connection
• Replaces frayed, cut, melted, or damaged cords that cause intermittent power or no power
• Helps eliminate burning smells, arcing, or visible insulation damage at the cord
• Matches OEM electrical connection style for proper fit and secure contact

• One power cord assembly

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the cord
• Verify cord routing and strain relief position to prevent pinch points or abrasion
• Use proper tools and fasteners; tighten connections securely but do not overtighten

Conduction heater for the freezer compartment that melts frost from the evaporator during defrost cycles, helping prevent ice buildup and maintain consistent cooling. Replaces a failed freezer conduction heater to restore defrost function. What it does:

• Heats the evaporator area during defrost cycles to melt accumulated frost and ice.
• Helps prevent excessive ice buildup that can reduce cooling efficiency.
• Common symptoms of a failing heater: visible ice/frost on the evaporator or freezer interior and inconsistent freezer temperatures.
• Designed as a replacement conduction heater for compatible GE freezer evaporator assemblies.

• Disconnect power to the appliance before servicing to avoid electric shock.
• Access typically requires removing the freezer evaporator cover or rear panel.
• Handle the element carefully to avoid damage.

This is a black replacement handle for the freezer door that restores a secure grip and original appearance. It provides a simple exterior swap to replace a cracked, loose, or missing freezer door handle. What it does:

• Provides a sturdy grip to open and close the freezer door
• Restores appearance when the original handle is cracked, broken, or missing
• Mounts to the freezer door using the existing handle fasteners for a direct-fit replacement
• Helps prevent further damage from using makeshift grips

• Basic hand tools (screwdriver or Torx) are typically required; confirm fastener type before starting
• Remove food and any door-mounted items to access mounting screws easily
• Align handle to existing holes and tighten fasteners securely but avoid over-tightening

The Freezer Fan with Felt is an OEM replacement part for GE refrigerators. It is designed to fit in the freezer compartment, to circulate cold air and maintain a consistent temperature throughout the freezer. This fan ensures proper airflow, preventing the formation of frost and ice buildup. The felt helps reduce noise and vibration, providing a quieter and smoother operation.

A bad freezer fan can occur due to various factors, including normal wear and tear, motor failure, or damage to the fan blades. If you notice symptoms such as unusual noises, reduced cooling performance, or frost accumulation in the freezer, it may indicate a need to replace the freezer fan with felt.

Symptoms of a bad freezer fan include:

• Unusual noises coming from the freezer
• Reduced cooling performance
• Frost accumulation in the freezer

Restore your refrigerator's freezer compartment by replacing the faulty freezer fan with felt using this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

Restore your appliance's factory look with this badge assembly. It replaces a missing, cracked, or faded logo on the refrigerator exterior, delivering a clean, professional appearance without affecting performance or operation.

• Decorative nameplate/logo for the refrigerator exterior
• Replaces cracked, faded, loose, or missing badge
• Restores a clean, factory appearance
• Cosmetic component; does not impact cooling or function

• Disconnect power before servicing the appliance
• Protect the finish; use a plastic trim tool to remove the old emblem if needed
• Clean and dry the mounting area; align with locating marks/holes and secure per your model diagram

The Refrigerator Handle is an OEM component specifically designed for GE refrigerator doors. It provides a simple grip that allows easy access to the refrigerator interior.

The handle serves an important functional purpose while maintaining a clean, understated aesthetic appearance. Its low-profile design does not detract from the visual lines of the door itself. 

Causes of a bad refrigerator handle usually stem from normal wear and tear over thousands of open/close cycles. Exposure to harsh household chemicals or external impacts can also potentially damage handled materials.

Symptoms of a bad refrigerator handle include:

• Looseness, wobbling, or instability when held
• Cracks, splits, or breaks in the plastic or metal 
• Difficulty opening the refrigerator door

This genuine GE replacement part restores the handle's grip and strength. Customers appreciate its like-new fit and finish. It is also compatible with Hotpoint, RCA, and select Kenmore models for reliable performance.

This SCR is a solid-state switching module that controls on/off power flow in select appliance circuits. Replacing a failed SCR helps stop intermittent operation and restores reliable switching for affected motors or heating elements. What it does:

• Regulates electrical switching in the control circuit to turn motors or heaters on and off.
• Used where a solid-state switch is required for smooth, repeatable control.
• Symptoms of a failing SCR: appliance won't start, runs intermittently, hums without operating, or a controlled circuit does not respond.
• Restores proper switching when the original SCR is shorted, open, or erratic.

• Disconnect power to the appliance before beginning service; follow lockout/tagout procedures.
• Handle as an electronic component—avoid static discharge and protect the spade terminals from bending or contamination.
• Ensure correct orientation and secure mounting; reconnect wiring exactly as shown on the appliance wiring diagram.

A replacement crossbar pinion that engages the ice-maker ejector crossbar to advance the harvest cycle. Installs on the ice maker drive assembly to restore proper rotation of the ejector and help clear ice from the mold. What it does:

• Drives the ice-maker crossbar/ejector during the harvest cycle so ice cubes are pushed out.
• Transfers rotation from the ice-maker motor/cam to the ejector crossbar.
• Common symptoms: ice maker won't advance or eject cubes, loud grinding or clicking from the ice bin, or visible broken/missing gear teeth.
• Restoring a worn or broken pinion can stop jamming and allow normal harvest cycles to resume.

• Disconnect power to the appliance before servicing; shut off the water if removing the ice maker assembly.
• Remove the ice maker per the manufacturer's instructions to access the pinion; handle plastic gears carefully to avoid damage.
• Inspect mating gears and the ejector crossbar for wear or damage and replace any damaged components to prevent repeat failure.
• After installation, restore power and run a test harvest cycle to ensure proper operation.

The Handle is an OEM part for GE refrigerators. It allows for easy opening and closing of the door. This handle is designed to provide a sturdy grip, making it convenient to access your food items.

A bad handle can be caused by wear and tear over time, excessive force applied to the handle, or damage due to accidental impact or mishandling.

Symptoms of a bad drawer handle include:

• Difficulty in opening or closing the door.
• Loose or wobbly handle.
• Cracks or breaks in the handle.

Replace your worn-out or damaged handle with this OEM part and restore your refrigerator. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This ice maker feeler arm senses the ice level in the bin and controls when the icemaker starts and stops. Replacing a bent, missing, or stuck arm restores correct shutoff and helps prevent overfilling or no-ice conditions.

• Monitors the ice bucket level and raises/lowers to start or stop ice production
• Shuts the icemaker off when the bin is full; allows production when lowered
• Common symptoms: ice maker won't stop making ice/overflows, no ice when the arm is stuck up, loose or missing arm
• Restores proper on/off control of the icemaker cycle

• Disconnect power and turn off the water supply before servicing
• Remove the ice bin and, the icemaker assembly to access the arm
• Transfer any reusable hardware; seat the arm fully in its pivot points so it moves freely
• Restore power, lower the arm to the On position, and allow time for the icemaker to cycle

8-18 CA HX 1/2 S

This felt tape is used in the refrigerator to cushion and seal mating parts, helping reduce vibration/squeaks and prevent chafing or small air leaks. Replace worn or missing tape to restore a quieter, more secure fit of covers and ducts.

• Provides a soft barrier between panels, ducts, or rails to minimize vibration and squeaks
• Helps seal minor gaps to support proper airflow paths
• Replaces deteriorated, compressed, or missing original felt tape
• Common symptoms include rattling/buzzing from covers or panels, squeaking drawers, or a loose cover that won't seat correctly

• Disconnect power to the refrigerator before servicing
• Note the original tape's location; remove the old tape and any residue
• Clean and dry surfaces thoroughly; apply the new tape in the same position (peel liner if adhesive-backed)
• Do not block vents, sensors, or fastener holes when applying

This replacement meat pan assembly provides a removable, easy-to-clean pan for storing deli and meat items and for catching drips to help keep the refrigerator interior sanitary and organized. What it does

• Holds deli/meat items and helps contain juices to reduce mess and cross-contamination.
• Replaces a cracked, warped, missing, or leaking meat pan that no longer seals or sits correctly.
• Restores proper fit on the shelf track so the pan slides in and out smoothly.
• Helps reduce odors and makes cleanup faster by keeping spills contained.

• Remove food and shelves from the area before installing to avoid spills.
• Slide the pan into the existing shelf track until it seats; most installs require no tools.
• Inspect supporting rails or brackets for damage and replace if worn to ensure proper fit.
• Follow basic food-safety cleaning before first use; disconnect power to appliances only if required per your model's service instructions.

This tuckaway shelf assembly replaces a broken or worn refrigerator tuck-away shelf so you can store items securely and slide the shelf out of the way when more space is needed. Restores safe, reliable shelf operation and storage flexibility. What it does:

• Provides a folding/tuckaway shelf surface that stows flat to create extra vertical space
• Replaces cracked, sagging, or non-locking tuckaway shelves that no longer stay in position
• Helps prevent stored items from tipping when the shelf is properly engaged
• Fits into existing shelf tracks and operates with the cabinet's original tuckaway mechanism

• 1 tuckaway shelf assembly

• High-level DIY replacement; remove items and use caution when lifting glass or plastic shelves
• Disconnect power only when working near electrical components or lights; otherwise appliance unplugging is not typically required for shelf swaps
• Inspect existing tracks and supports; do not force the shelf into damaged tracks
• If the shelf includes glass, handle with care and wear cut-resistant gloves