Glc2940fs1 Parts

This replacement drawer body restores a smooth-sliding storage bin in your appliance. Integrated rollers let the drawer glide on its tracks, keeping items organized and easy to access when the original is cracked, warped, or difficult to open.

• Forms the storage bin and supports items within the compartment
• Built-in rollers enable smooth travel along the drawer rails/tracks
• Helps resolve sticking, popping off track, rough movement, or broken tabs
• Restores proper fit and slide action for everyday use

• Empty and remove the damaged drawer; transfer any reusable front trim or inserts from the old drawer if needed
• Clean and inspect the rails/tracks; align the rollers with the track openings and slide in level until fully seated
• Do not force the drawer—re-align if resistance is felt to avoid damaging tabs or rails
• Avoid lubricants; wipe tracks and rollers with mild soap and water only

This middle conduit carrier secures the dishwasher's water feed tube so it stays aligned as the rack moves. Replacing a cracked or missing carrier helps restore reliable spray delivery and consistent cleaning performance.

• Secures and guides the middle water conduit/feed tube on the rack
• Keeps the conduit aligned with the rear water port for consistent spray
• Helps prevent rack binding or rattling from a loose feed tube
• Helps with weak spray or poor cleaning on the upper rack when the carrier is damaged

• Disconnect power and turn off water before servicing
• Pull the rack forward; release the old carrier's tabs or fastener and detach from the feed tube
• Snap or fasten the new carrier in place; ensure the conduit seats fully at the rear port
• Verify smooth rack travel and run a brief test cycle to check operation

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place

This glide is a low-friction slide used in select cooking appliances to support and guide a moving component, such as a lower drawer. Replacing a worn or broken glide restores smooth travel and proper alignment without sticking or scraping.

• Provides a smooth sliding surface for the mating part
• Helps keep the component aligned as it opens and closes
• Reduces friction and wear during movement
• Failure symptoms include sticking, scraping noises, uneven travel, or the component coming off track

• Disconnect power and allow the appliance to cool before servicing
• Remove the sliding component (e.g., drawer) to access the glide
• Remove the damaged glide and install the new one, transferring any screws or clips as needed
• Reinstall and test to ensure smooth, even movement

Mid spray arm bracket that secures the middle spray arm inside the dishwasher tub, keeping the arm aligned so it can rotate freely and deliver water for thorough cleaning. What it does:

• Holds the middle spray arm in position so it can spin and distribute water across the load.
• Maintains proper spray-arm alignment to help restore even cleaning coverage.
• Common symptoms: spray arm droops, wiggles, becomes detached, makes noise, or fails to rotate.
• Replaces a worn or broken support bracket that can interfere with spray-arm operation.

• Disconnect power to the appliance (turn off breaker) before servicing.
• You may need to remove the lower/upper rack and the spray arm to access the bracket.
• Handle small clips and sharp edges carefully; inspect adjacent parts for wear while replacing.

This junction box cover replaces the appliance's electrical access panel to protect wiring and provide a secure entry point for the power cord. It restores a finished, safe electrical connection area and helps prevent exposed wiring. What it does

• Covers and protects the appliance's electrical junction box from dust and accidental contact
• Provides the mounting location and opening for the power cord/strain-relief connection
• Secures wiring and helps keep wire connections contained and stable
• Common symptom: cover cracked, missing, or loose—exposed wires or inability to secure the power cord

• Disconnect power at the breaker or unplug the appliance before servicing electrical parts
• Remove mounting screws from the old cover and replace with the new cover; retain or replace strain relief as needed
• Inspect the cord and wiring while access is open; replace any damaged wiring or strain relief components
• Follow the appliance manufacturer's instructions and local electrical codes for safe installation

This burner seal is a replacement gasket that fits around a cooktop burner to help keep the burner area sealed and easier to clean. It helps maintain a proper seal between the burner base and the cooktop surface. What it does:

• Seals the gap between the burner and cooktop to limit food, grease and liquid from entering the burner cavity
• Helps keep the burner seated and reduces wobble or misalignment
• Supports cleaner cooktop surfaces and simplifies wipe-downs
• Can help maintain consistent ignition area by keeping debris away from the burner base

• Turn off power to the appliance and ensure the cooktop is completely cool before starting.
• Remove burner grate and lift off the burner cap and burner head as needed to access the seal.
• Clean the seating area of any grease or debris, then press the new seal evenly into place before reassembling.

This surface burner seal sits between the burner and the cooktop opening to block spills and air leaks, helping the burner seat correctly and keeping the cooktop area cleaner.

• Creates a tight seal between the surface burner and the cooktop opening
• Helps prevent liquids and debris from getting under the cooktop
• Supports proper burner alignment and consistent heat/flame
• Replace if torn, brittle, swollen, or permanently compressed; common signs include seepage under the top, uneven heating/flame, or the burner not sitting level

• Disconnect power; for gas ranges, also shut off the gas supply. Allow the cooktop to cool completely.
• Remove grates, burner cap, and burner head/base as applicable; lift off the old seal.
• Clean the mating surfaces; position the new seal evenly around the opening.
• Reassemble burner parts and test for proper seating and even heating/flame.

Evaporator fan motor that circulates cold air over the evaporator coil to help maintain even refrigerator temperatures. Replacing a failing motor restores airflow, reduces warm spots and frost buildup, and cuts down on excessive fan noise. What it does:

• Spins the evaporator fan blade to move cold air through the evaporator and into the cabinet.
• Promotes even cooling to prevent warm zones and food spoilage.
• Stops or reduces abnormal noises caused by a worn or seized motor.
• Helps prevent frost accumulation linked to poor airflow.

• Disconnect power to the appliance before beginning any repair.
• Handle the motor and fan blade carefully; ensure the fan blade is seated properly on the shaft.
• Remove evaporator/fan housing panels and retain screws and clips for reassembly; verify wiring connectors match before reconnecting.

Electronic control restores digital control of refrigerator settings by receiving inputs and sending signals to temperature and system components. Replaces an unresponsive or malfunctioning control board to help restore predictable user control and operation. What it does:

• Interprets user inputs and sensor signals to manage compressor, fans, defrost cycles, and lighting control
• Regulates timing and on/off control for cooling and defrost functions
• Commonly replaced when controls are unresponsive, display is blank or erratic, or cooling cycles behave inconsistently
• Used to correct intermittent or failed electronic control behavior tied to user-interface and system timing

• Disconnect power to the appliance before beginning any service
• Handle the board as a static-sensitive electronic component; avoid rough handling and contact with terminals
• Installation typically requires removing interior panels and unplugging the wire harness; retain fasteners for reassembly

This heat-resistant insulation helps contain oven heat and shield surrounding components. Replacing worn insulation supports faster, more consistent preheating, steadier baking temperatures, and cooler exterior panels for safer, more efficient operation. What it does:

• Wraps/lines the oven cavity or panels to reduce heat loss and protect nearby wiring and controls
• Helps the oven preheat efficiently and maintain consistent cooking temperatures
• Limits heat transfer to exterior panels and surrounding cabinetry
• Common signs of failure: longer preheat times, temperature swings, unusually hot sides/back, or insulation that is burnt, brittle, soaked, or missing

• 1 insulation piece

• Disconnect power and, if applicable, shut off gas before servicing
• Access typically requires removing rear/side panels or sliding the unit out; take photos to aid reassembly
• Wear gloves and a dust mask; handle gently—do not compress insulation and keep clear of sensors/wiring
• Re-secure with original clips/tape, reinstall panels, then test preheat and check for abnormal exterior heat

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.

This clamp secures a hose or small tubing connection on compatible GE laundry appliances to help prevent leaks and keep the connection stable during operation. Durable metal construction resists vibration and wear. What it does:

• Holds a hose or tube firmly to a fitting to reduce leaks and loss of water or airflow
• Stops hose slippage caused by vibration or pressure changes
• Helps restore a tight connection after hose replacement or service
• Simple, low-profile design for use in confined appliance spaces

• Disconnect power and shut off water supply before servicing
• Drain hoses and remove remaining water to avoid spills
• Use the proper screwdriver or nut driver to tighten; do not over-tighten
• Inspect the hose and fitting for wear and replace if damaged before reinstalling the clamp