Gne29gynbfs Parts

The Mullion Striker is an OEM part for GE refrigerators responsible for securing the mullion or flipper door in place when it is closed, ensuring a tight seal and temperature inside the refrigerator.

A bad mullion striker can be caused by normal wear and tear over time, damage due to excessive force or impact, or misalignment of the mullion assembly. If you notice that the mullion door does not stay securely closed, causing a gap or allowing warm air to enter the refrigerator, it may indicate a problem with the mullion striker.

Symptoms of a bad mullion striker include:

• Difficulty in keeping the mullion door closed
• Visible gaps or improper sealing when the door is closed
• Condensation or frost buildup around the mullion area
• Unusual noises from the mullion assembly

Replace your faulty mullion striker with this genuine OEM part to restore your refrigerator. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This replacement power cord harness connects the appliance's incoming mains power to its internal wiring, restoring a secure electrical path. Use it to replace damaged or worn harnesses to help resolve power loss or intermittent operation. What it does:

• Routes mains power from the inlet to the control board and internal components
• Replaces frayed, cut, or heat-damaged wiring that can cause intermittent power or complete power failure
• Restores secure connector and terminal connections to reduce arcing or loose-contact symptoms
• Maintains factory routing and strain relief when installed correctly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Replace with the same connector orientation and routing as the original harness to ensure correct fit and strain relief
• Inspect related terminals and wire insulation; if you see melted terminals or heavy corrosion,

The Heater Harness Fz W/tco is an OEM part for GE refrigerators. This essential component is responsible for preventing ice buildup and ensuring proper defrosting in the freezer compartment. This freezer heater harness with TCO defrost thermostat helps maintain the optimal temperature and humidity levels in your freezer. It is designed to melt away any ice or frost that may accumulate on the freezer coils, preventing them from obstructing airflow and affecting the cooling performance.

A bad freezer heater harness can occur due to wear and tear, electrical faults, or other factors. If you notice symptoms such as excessive ice buildup, inconsistent cooling, or frequent freezer defrosting cycles, it may be time to replace this part.

Symptoms of a bad freezer heater harness with TCO defrost thermostat include:

• Excessive ice buildup
• Inconsistent cooling
• Frequent freezer defrosting cycles

Prevent ice-related issues by replacing the faulty freezer heater harness with TCO defrost thermostat with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Air Tower is an OEM component for GE side-by-side refrigerator models designed to distribute cold airflow across shelves and crisper bins. Strategically located in the fresh food compartment, it facilitates even temperature regulation within. Efficient airflow relies on an intact tower design.

Symptoms of a defective air tower include:  

• Warm spots or frost buildup noticed on certain shelves and walls   
• Fluctuating temperatures displayed on control panels
• Condensation or moisture issues in unaffected areas

Causes stem from common blockages within vent channels from food debris over time, wear of fan blade bearings reducing distribution power, or cracks in injection-molded tower walls.

Replacing with this genuine GE part restores optimum temperature balance throughout the refrigerator. Compatible for replacement fits Hotpoint, RCA, or Kenmore units seeking uniform chilling without dead zones developing. Regular cleaning helps but replacement maintains long-term efficiency.
 

This clip secures the evaporator thermistor to the evaporator tubing so the control can read coil temperature accurately. Replacing a damaged or missing clip helps restore correct cooling and defrost performance by keeping the sensor firmly in place. What it does:

• Holds the evaporator thermistor tightly against the evaporator coil/tubing for accurate temperature sensing
• Supports proper cooling regulation and defrost cycle timing
• A loose or misplaced sensor may show temperature swings, long run times, or frost buildup on the evaporator
• Restores correct sensor placement after repairs or when the original clip is lost or broken

• 1 evaporator thermistor clip

• Unplug the refrigerator; interior metal edges and fins are sharp—wear cut-resistant gloves
• Remove the evaporator cover to access the sensor; note the original sensor location and orientation
• Transfer the thermistor into the new clip and attach it at the same spot so the sensor makes firm contact; do not pinch wires
• Reinstall panels, keep wiring clear of the fan, and restore power

The Flat Chrome Badge is an OEM part for GE refrigerators. It is responsible for displaying the GE logo and model information on the front of the refrigerator. As an identifiable brand marker, the badge contributes to the overall appearance and style of the appliance.

Causes of a bad badge can include damage from impacts or bending, discoloration or tarnishing over time, or simple wear and tear that renders the badge appearance faded or illegible.

Symptoms of a bad badge include:

• A missing, loose, crooked or illegible badge
• Signs of denting, scratching or corrosion
• An outdated or inconsistent badge that doesn't match the model

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

The 2-pack Hinge End Cap Assembly is an OEM replacement part for GE refrigerators. This assembly is responsible for providing support and stability to the refrigerator door hinges, ensuring smooth opening and closing.

A bad hinge end cap assembly can occur due to regular wear and tear or accidental damage. If you notice symptoms such as a loose or sagging door, difficulty in opening or closing the door, or the door not staying securely in place, it may indicate a need to replace this assembly.

Symptoms of a bad hinge end cap assembly include:

• Loose or sagging refrigerator door
• Difficulty in opening or closing the door
• Door not staying securely closed

Restore your refrigerator's door by replacing the faulty hinge end cap assembly with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This mounting screw secures appliance components to the chassis for a tight, rattle-free fit. Replacing a missing, stripped, or corroded fastener helps keep panels, brackets, or burner assemblies properly aligned and secure.

• Fastens designated parts to the appliance frame or mounting points
• Helps maintain proper alignment of panels, trim, brackets, or burner assemblies
• Restores hold when the original screw is worn, rusted, or lost
• Symptoms include loose or wobbly components, rattling/vibration, or visible gaps

• Disconnect power; allow all surfaces to cool. For gas units, also shut off the gas supply.
• Use the correct driver/bit; avoid cross-threading.
• If mating threads or clip/nut are damaged, repair or replace them before installing.
• Tighten until secure; do not overtighten to prevent stripping.

Replacement grille thermistor. This temperature sensor monitors air at the grille location and relays the signal to the control so cooling and defrost responses stay consistent and food stays within target temperatures.

• Senses ambient air temperature at the grille and varies resistance with temperature
• Sends data to the control to help regulate compressor/fan run time and defrost intervals
• Aids in maintaining stable refrigerator and freezer temperatures
• A failing sensor may lead to temperature swings, extended run time, or irregular defrosting

• Disconnect power before servicing
• Remove the grille/kickplate to access the sensor and its connector
• Disconnect the old sensor, install the new one, and route wiring as originally; ensure the sensor is fully seated and wires aren't pinched
• Restore power and allow up to 24 hours for temperatures to stabilize

This replacement power cord provides the appliance's main AC connection so it can receive power and operate reliably. It restores a safe, factory-style power connection when the original cord is damaged or worn. What it does

• Supplies mains power to the appliance through the cabinet connection
• Replaces frayed, cut, melted, or damaged cords that cause intermittent power or no power
• Helps eliminate burning smells, arcing, or visible insulation damage at the cord
• Matches OEM electrical connection style for proper fit and secure contact

• One power cord assembly

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the cord
• Verify cord routing and strain relief position to prevent pinch points or abrasion
• Use proper tools and fasteners; tighten connections securely but do not overtighten

Conduction heater for the freezer compartment that melts frost from the evaporator during defrost cycles, helping prevent ice buildup and maintain consistent cooling. Replaces a failed freezer conduction heater to restore defrost function. What it does:

• Heats the evaporator area during defrost cycles to melt accumulated frost and ice.
• Helps prevent excessive ice buildup that can reduce cooling efficiency.
• Common symptoms of a failing heater: visible ice/frost on the evaporator or freezer interior and inconsistent freezer temperatures.
• Designed as a replacement conduction heater for compatible GE freezer evaporator assemblies.

• Disconnect power to the appliance before servicing to avoid electric shock.
• Access typically requires removing the freezer evaporator cover or rear panel.
• Handle the element carefully to avoid damage.

The Freezer Fan with Felt is an OEM replacement part for GE refrigerators. It is designed to fit in the freezer compartment, to circulate cold air and maintain a consistent temperature throughout the freezer. This fan ensures proper airflow, preventing the formation of frost and ice buildup. The felt helps reduce noise and vibration, providing a quieter and smoother operation.

A bad freezer fan can occur due to various factors, including normal wear and tear, motor failure, or damage to the fan blades. If you notice symptoms such as unusual noises, reduced cooling performance, or frost accumulation in the freezer, it may indicate a need to replace the freezer fan with felt.

Symptoms of a bad freezer fan include:

• Unusual noises coming from the freezer
• Reduced cooling performance
• Frost accumulation in the freezer

Restore your refrigerator's freezer compartment by replacing the faulty freezer fan with felt using this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

Restore your appliance's factory look with this badge assembly. It replaces a missing, cracked, or faded logo on the refrigerator exterior, delivering a clean, professional appearance without affecting performance or operation.

• Decorative nameplate/logo for the refrigerator exterior
• Replaces cracked, faded, loose, or missing badge
• Restores a clean, factory appearance
• Cosmetic component; does not impact cooling or function

• Disconnect power before servicing the appliance
• Protect the finish; use a plastic trim tool to remove the old emblem if needed
• Clean and dry the mounting area; align with locating marks/holes and secure per your model diagram

The Refrigerator Handle is an OEM component specifically designed for GE refrigerator doors. It provides a simple grip that allows easy access to the refrigerator interior.

The handle serves an important functional purpose while maintaining a clean, understated aesthetic appearance. Its low-profile design does not detract from the visual lines of the door itself. 

Causes of a bad refrigerator handle usually stem from normal wear and tear over thousands of open/close cycles. Exposure to harsh household chemicals or external impacts can also potentially damage handled materials.

Symptoms of a bad refrigerator handle include:

• Looseness, wobbling, or instability when held
• Cracks, splits, or breaks in the plastic or metal 
• Difficulty opening the refrigerator door

This genuine GE replacement part restores the handle's grip and strength. Customers appreciate its like-new fit and finish. It is also compatible with Hotpoint, RCA, and select Kenmore models for reliable performance.

This SCR is a solid-state switching module that controls on/off power flow in select appliance circuits. Replacing a failed SCR helps stop intermittent operation and restores reliable switching for affected motors or heating elements. What it does:

• Regulates electrical switching in the control circuit to turn motors or heaters on and off.
• Used where a solid-state switch is required for smooth, repeatable control.
• Symptoms of a failing SCR: appliance won't start, runs intermittently, hums without operating, or a controlled circuit does not respond.
• Restores proper switching when the original SCR is shorted, open, or erratic.

• Disconnect power to the appliance before beginning service; follow lockout/tagout procedures.
• Handle as an electronic component—avoid static discharge and protect the spade terminals from bending or contamination.
• Ensure correct orientation and secure mounting; reconnect wiring exactly as shown on the appliance wiring diagram.

A replacement crossbar pinion that engages the ice-maker ejector crossbar to advance the harvest cycle. Installs on the ice maker drive assembly to restore proper rotation of the ejector and help clear ice from the mold. What it does:

• Drives the ice-maker crossbar/ejector during the harvest cycle so ice cubes are pushed out.
• Transfers rotation from the ice-maker motor/cam to the ejector crossbar.
• Common symptoms: ice maker won't advance or eject cubes, loud grinding or clicking from the ice bin, or visible broken/missing gear teeth.
• Restoring a worn or broken pinion can stop jamming and allow normal harvest cycles to resume.

• Disconnect power to the appliance before servicing; shut off the water if removing the ice maker assembly.
• Remove the ice maker per the manufacturer's instructions to access the pinion; handle plastic gears carefully to avoid damage.
• Inspect mating gears and the ejector crossbar for wear or damage and replace any damaged components to prevent repeat failure.
• After installation, restore power and run a test harvest cycle to ensure proper operation.