Gscs3pgx Parts

This refrigerator lamp socket holds an E12-base appliance bulb and provides the electrical connection for the light fixture. Replace it when the light won't turn on or flickers despite a known-good bulb and functioning door switch.

• Secures an E12 (candelabra) bulb and supplies power to it
• Works with the door/light switch to illuminate the compartment or dispenser area
• Typical failures include heat damage, cracking, or internal contact wear
• Symptoms: no light, intermittent flicker, or a bulb that won't seat firmly

• Disconnect power to the refrigerator before servicing
• Remove any lens/cover, note wire placement, and install the new socket in the original orientation
• Use an E12-base appliance bulb with the wattage specified on your model's rating label
• Restore power and verify operation with the door switch

This crisper cover glass is the removable glass panel that fits into the crisper pan cover. It restores a flat, sturdy surface above the drawers and helps keep small spills contained for easier cleanup.

• Forms the shelf surface above the crisper drawers within the cover frame
• Helps contain minor spills and supports stored food items
• Replace if cracked, shattered, bowed, or missing
• Symptoms include broken glass, items tipping, or drawers rubbing the cover

• Disconnect power and clear the shelf area before starting
• Remove crisper drawers and lift off the cover frame to access the glass
• Carefully remove the old panel and seat the new glass fully in the frame channels
• Reinstall the cover and drawers, then restore power

This ice dispenser auger drive mounts on the dispenser motor shaft and engages the ice bucket auger. Replacing a worn or stripped drive restores the connection so your refrigerator can move ice smoothly to the chute.

• Couples the dispenser motor to the ice-bin auger to rotate and move ice toward the chute
• On models with crushers, also drives the crushing mechanism
• Worn or rounded splines can cause little or no ice dispensing even though the motor runs
• May produce clicking/grinding noises from the door during dispense
• Visible cracking or play at the coupling indicates replacement is needed

• Unplug the refrigerator and shut off water before servicing
• Remove the ice bin to access the dispenser motor shaft in the freezer door
• Note the orientation; remove the old drive and seat the new drive fully on the shaft, transferring any original hardware if present
• Reinstall the ice bin, restore power, and test ice dispense

The Freezer Light Cover is an OEM replacement part for GE refrigerators designed to protect the light bulb in the freezer compartment from any potential damage or breaks. It helps maintain a safe and well-lit freezer environment, making it easier to locate and retrieve items.

A bad freezer light shield cover can occur due to regular wear and tear or accidental damage. If you notice symptoms such as a flickering or dim freezer light, or if the light bulb is exposed and vulnerable, it may indicate a need to replace this part.

Symptoms of a bad freezer light cover include:

• Flickering or dim freezer light
• Exposed or broken light bulb
• Insufficient lighting 

Restore lighting in your freezer by replacing the faulty freezer light cover with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

Water line from water valve up to icemaker fill tube.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

This pan frame assembly forms the cover over a refrigerator storage drawer and supports the glass shelf above. Replace a cracked or warped frame to restore smooth drawer operation and a sturdy, level storage surface.

• Supports and aligns the drawer(s) beneath while carrying the load of the shelf above
• Restores a stable, level surface when the original frame is cracked, bowed, or broken
• Helps drawers open and close smoothly when tracks and stops are intact
• Common symptoms: shelf sagging, wobble, broken corners/tabs, drawer binding or misalignment

• Disconnect power and remove food from the affected shelf area
• Carefully remove the glass insert and drawer(s); handle tempered glass with care
• Lift out the old frame; seat the new frame fully on its supports and ensure tabs/slots are engaged
• Reinstall the glass and drawer(s); verify smooth drawer travel and that the shelf sits level

This small hinge sleeve fits into the refrigerator door to guide the hinge pin and keep the door aligned. Replacing a worn thimble can reduce squeaks and wobble and help the door open smoothly and seal correctly.

• Sits in the door hinge pocket and guides the hinge pin
• Provides a smooth bearing surface for easy opening/closing
• Helps maintain door alignment and consistent gasket contact
• Wear may show as squeaking, door play/sag, rubbing, or incomplete closing

• Disconnect power and remove items from the door before starting
• Support the door; remove hinge cover and fasteners, then lift door off the hinge pin
• Pull out the old thimble and press the new thimble fully into the door hinge pocket
• Reinstall door and hinges; verify alignment and that the gasket seals all around

This fixed freezer shelf restores a sturdy, level storage surface in the freezer compartment. Replace a broken or missing shelf to regain organization, correct spacing, and full storage capacity.

• Provides a fixed-position storage surface inside the freezer
• Helps keep items level, organized, and easy to access
• Restores proper spacing with adjacent shelves, drawers, or baskets
• Replaces a cracked, warped, or missing shelf

• Disconnect power before servicing; wear gloves to protect hands
• Empty the area, then align the shelf with the side-wall slots or supports
• Slide or place the shelf into the supports until fully seated and level
• Distribute weight evenly and avoid overloading after installation

This #8-18 x 5/8-inch Torx T20 screw secures panels, brackets, and trim in your appliance. It replaces missing or damaged hardware to restore a tight, reliable hold and reduce looseness or rattling.

• Fastens sheet-metal or plastic components to the appliance cabinet or frame
• Replaces missing, stripped, or corroded screws to maintain proper fit
• Helps reduce vibration and rattling from unsecured parts
• Torx T20 drive; #8-18 thread; 5/8-inch length

• Disconnect power and shut off water before servicing
• Use a T20 Torx driver; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping
• Wear cut-resistant gloves; sheet-metal edges can be sharp

This is the rear motor cover used in select GE refrigerators. It shields the motor area at the back of the compartment, helping direct airflow and protect the fan/motor assembly for reliable cooling performance.

• Protects the motor/fan area from debris and damage
• Helps channel air correctly through the compartment
• Cracks, broken tabs, or missing cover can lead to noise, poor airflow, frost, or temperature swings
• Restores proper fit and finish inside the compartment

• Unplug the refrigerator before servicing
• Remove shelves/bins obstructing access; retain screws/clips
• Carefully release locking tabs and transfer any reusable hardware
• Ensure the cover seats fully and resecure all fasteners before powering on

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly

Color: Chrome. It measures about 7-1/2 inches wide by 4 inches deep. For Black, order WR17X12324.

Keep water and ice flowing without internal filtration. This MSWF water filter bypass plug replaces the filter to seal the housing and route water properly to the dispenser and ice maker when a filter is not used.

• Installs in place of the MSWF filter to bypass filtration
• Maintains water flow to the dispenser and ice maker with no filter installed
• Helpful for troubleshooting restricted flow or when using an external filtration system
• Seals the filter head to help prevent leaks during bypass
• Note: No water is filtered while this plug is installed

• Shut off the water supply and dispense water to relieve system pressure
• Remove the MSWF filter; align and twist the bypass plug to lock into the filter head
• Restore water, check for leaks, and run the dispenser briefly to purge air
• Follow your refrigerator's instructions and use appropriate hand/eye protection

This power cord assembly supplies electrical power from the wall outlet to your refrigerator. Replace a cut, frayed, or overheated cord to restore safe, reliable operation and eliminate intermittent power loss caused by a damaged cord. What it does:

• Provides the electrical connection between the household outlet and the refrigerator's wiring
• Helps resolve no-power or intermittent power when the cord is moved
• Addresses visible damage such as cuts, cracks, fraying, or a melted/discolored plug
• Mitigates arcing, sparking, or a burning odor originating from the cord or plug area

• One power cord assembly

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Pull the refrigerator forward for access; note the original cord routing and connections
• Install the new cord along the same path and secure any built-in strain relief; ensure the ground connection is properly seated
• Restore power and verify operation