Gsd1222vbb Parts

Repair parts arrived super fast. Installed the new parts according to the supplied instructions. All went well. It took over 2 hours because the unit had to be removed after the water and power were disconnected and then the initial problem diagnosed (motor brushes worn beyond service limits). The removal of the spray bar tower assembly was a challenge until it was discovered that the tower unscrews in a CW direction from the bar that then allowed access to the attachment screw that holds that... Read more

Dishwasher needed new wheel that mounted to upper rack.There are 4 total that make the rack roll in and out. Replaced both side rails and rail caps (4- only 50 cents each) along with new upper rack that came with wheels installed. One side rail was bent so decided to spend a little extra and replace both. Might of been able to replace just one broken rack wheel but rack was old and was rusting in some areas so decided to just replace it. Read more

I took the inside plate off door. Removed old gasket. Broke styrofoam vent buffernbecause I grabbed it in the wrong place. Ordered both a gasket and vent buffer from your company. It came in 2 days as promised. I had to empty dishwasher of about 2-3 inches of water as with the door apart and knowing it would leak I had to shut off electric supply and hand empty machine first cup by cup and then towel by towel. (Towel method worked well). Then I took a blow dryers to the inside of dishwasher, ... Read more

After reading all the systems on this site. It made it pretty easy to diagnose the problem. The part came in and slapped it in within a few minutes. Ran it and made my wife happy. She was under undue stress without her dishwasher and now I am her superman! Will order again from you. Part arrived quickly and the info you provided really saved me a ton of money! Seriously thank you. Read more

Replaced the upper rollers and the rack rollers along with new caps for the slide bars. Everything fit perfectly and it fixed the problem. A bit pricey but cheaper than a new dishwasher plus installation Read more

1. Replaced the Dishwasher motor and pump assembly. 2. Replaced the lower arm sprayer. 3. Replaced the Sump and filter. Replaced both the inlet and outlet hoses. 4. Replaced the Airgap. 5. Replaced Float Dome. 6. Replaced Water Inlet Valve. Parts $220 for Dishwasher Estimated Labor $400.00 Labor $0.00 Parts $100.00 for Pullout Faucet Estimated Labor $175.00 Labor $0.00 Read more

• Leaking

The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more

There is a plastic "snapping" feature (Two plastic tabs that when pressed together can fit into the holes on the spray arm. Once in there, the tabs expands and keep the spray arm in place) that comes out of the top onto which the spray arm is attached to. That plastic piece broke and the spray arm fell off. It wasn't clear how the snapping feature was attached to the top of the dishwasher at first. I was looking for a replacement for it and could not find it on any of the assembly diagram... Read more

1. Replaced the Dishwasher motor and pump assembly. 2. Replaced the lower arm sprayer. 3. Replaced the Sump and filter. Replaced both the inlet and outlet hoses. 4. Replaced the Airgap. 5. Replaced Float Dome. 6. Replaced Water Inlet Valve. Parts $220 for Dishwasher Estimated Labor $400.00 Labor $0.00 Parts $100.00 for Pullout Faucet Estimated Labor $175.00 Labor $0.00 Read more

• Will not dispense detergent

The timer was replaced. It took about 35 minutes. The most difficult thing was holding the door down. Read more

1. Replaced the Dishwasher motor and pump assembly. 2. Replaced the lower arm sprayer. 3. Replaced the Sump and filter. Replaced both the inlet and outlet hoses. 4. Replaced the Airgap. 5. Replaced Float Dome. 6. Replaced Water Inlet Valve. Parts $220 for Dishwasher Estimated Labor $400.00 Labor $0.00 Parts $100.00 for Pullout Faucet Estimated Labor $175.00 Labor $0.00 Read more

Took the impeller out, removed the pump, replaced connector, put new clamps on, reassembled and checked for leaks. I just followed Arts video, went smooth. Wifes happy, things are good. Thanks AppliancePartsPros.com Read more

1. Removed the water inlet/shut off valve, removed and cleaned the screen. while the valve was removed applied electrical power to the valve and it worked just fine. 2. replaced the broken float switch. Read more

Found AppliancePartsPros.com and looked up parts and ordered replacement parts. ( VERY easy!) Replaced the spray arm assembly and door vent via the handy Q&A repair section, as well as a thorough cleaning, and VOILA! Clean dishes again!! Thanks for making it easy! Read more