Gtun275gmww Parts

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

This selector switch mounts behind the console knob and lets you choose wash settings on your washer. Replacing a worn switch restores reliable selection so the control responds to the setting you intend.

• Allows the user to select a wash option and sends that choice to the timer/control
• Helps when the knob won't click or hold a setting
• Addresses issues where settings don't change or only one option works
• Can resolve dead or intermittent positions on the selector

• Disconnect power before servicing
• Access the control console; remove the knob and the switch's retaining hardware
• Move wire connectors from the old switch to the new one one at a time to maintain correct positions
• Secure the new switch, reinstall the knob, and reassemble the console

The Funnel Shower Head is an OEM part for GE washing machines, designed to distribute water evenly over the laundry during the wash cycle. This component plays a crucial role in ensuring that water and detergent mix effectively, saturating the clothes thoroughly to achieve optimal cleaning performance. The design of the Funnel Shower Head ensures a gentle yet efficient distribution pattern, minimizing the risk of fabric damage while maximizing the removal of dirt and stains.

Causes of a bad Funnel Shower Head can stem from clogging due to mineral deposits from hard water, damage to the part itself, or a blockage caused by foreign objects. 

Symptoms of a bad Funnel Shower Head include:

• Inadequate water distribution during the wash cycle
• Clothes not being fully saturated or washed evenly
• Decreased washing machine performance due to poor water flow

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This water inlet valve assembly regulates the flow of household water into the washer during fill cycles. Replacing it restores consistent fills and helps resolve issues like no water, slow fills, or water leaking into the tub.

• Opens and closes to control water flow into the machine as commanded by the control system
• Helps the washer reach proper fill levels for wash and rinse cycles
• Typical symptoms: no fill, slow fill, fill errors, or water seeping into the tub when the washer is off
• Leaks around the valve or hose connections can also indicate the part has failed

• Unplug the washer and turn off both water supply valves before servicing
• Label hot and cold hoses and take a reference photo before removal
• Expect residual water; use a towel or container. Reconnect electrical connectors and hoses; tighten fittings without overtightening
• After installation, open supply valves and run a test fill while checking for leaks

Size: 10-12 a. Includes 12 screws.

The Idler Arm Assembly is an OEM component specifically designed for GE dryers. It is a vital part that helps transfer power from the motor to the tumbling action of the dryer drum. The idler arm assembly allows the belt to provide smooth, consistent power to operate the drum efficiently during each cycle.  

Symptoms of a bad idler arm assembly include:

• Squealing or grinding noises coming from the dryer motor or drum area
• The dryer drum not rotating or spinning slowly
• Loose, cracked, or worn idler pulley
• A worn or slipping dryer belt 

Causes of failure can be normal wear and tear over extended use. Excess vibration from an unbalanced load or a dropped object inside the dryer could also potentially damage the idler arm.

This part is compatible with Hotpoint, RCA, and Kenmore dryer models.

This is a small screw, and it is made for dryers, washers, and washer dryer combos. This is a genuine replacement part made by General Electric. Screws are common in these appliances and can cause many difficulties if they become loose, damaged, or missing.A new screw might be needed if there are areas in the appliance that seem off balance or not level. Another way to tell if a new screw is needed is if there are parts in the appliance that are loose or falling off. This is common over many years of normal use as the shaking of washers and dryers can eventually lead to loose screws. Be sure the washer or dryer is completely off before attempting to replace any screws.This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with washers, dryers, and washer dryer combos made by General Electric.

This exhaust blower gasket seals the joint between the dryer's blower outlet and exhaust duct. It helps maintain proper airflow and contain lint and heat, supporting efficient drying and preventing leaks into the cabinet or laundry area. What it does:

• Seals the blower-to-exhaust connection to prevent air and lint leaks
• Helps maintain designed airflow through the drum and vent system
• Can reduce warm air or lint escaping inside the cabinet

• 1 gasket

• Disconnect power; for gas dryers, shut off gas and disconnect the supply. Allow the dryer to cool.
• Access the blower housing/exhaust duct; remove panels as needed.
• Remove the old gasket and any residue; clean mating surfaces and lint before installing.
• Seat the new gasket evenly and reassemble; avoid overtightening fasteners and ensure the home vent is clear.

This trap duct and felt kit restores the dryer's front airflow path and drum seal. Replacing a damaged duct or worn felt helps maintain proper airflow, improve drying performance, and reduce lint leaks and noise. What it does:

• Routes exhaust air through the lint filter housing to the blower
• Seals the drum front to prevent air leaks and reduce fabric snagging
• Helps address long dry times, lint escaping into the cabinet, and scraping/squealing from a worn front seal
• Replaces cracked, warped, or melted lint trap duct components

• One trap duct and one felt seal

• Disconnect power; shut off gas supply for gas dryers before servicing
• Remove top/front panels to access the lint filter housing and front bulkhead; support the drum as needed
• Clean mating surfaces; install the felt with the soft pile facing the drum to form a continuous, even seal
• Reuse original fasteners/hardware; the lint filter seats fully and the drum turns freely before testing

This is the drive motor and pulley assembly for GE dryers. It turns the drum via the belt and powers the blower wheel, restoring proper tumbling and airflow when the original motor is weak, noisy, or not starting.

• Powers the drive belt to rotate the dryer drum
• Turns the blower wheel to move air through the drum and exhaust
• Typical symptoms of a failing motor: dryer won't start, drum won't turn, loud humming/buzzing, or stops mid-cycle from overheating
• Restores consistent tumbling and drying performance

• Disconnect power; for gas models, also shut off the gas supply
• Access the motor by removing panels and relieving belt tension; remove drum as needed
• Label/photograph wiring and transfer the blower wheel and any brackets or clamps from the old motor
• Spin the drum by hand before restoring power

This washer agitator assembly mounts on the drive shaft and creates the back-and-forth wash action that moves laundry through water and detergent. Replacing a worn or cracked agitator restores proper turnover and cleaning performance.

• Attaches to the drive shaft/transmission to produce the oscillating wash action
• Circulates clothes for even cleaning and reduced tangling
• Replace if the washer won't agitate, the agitator free-spins or slips, laundry stays on top, or it's visibly cracked/loose
• Can also help address squeaking, clicking, or grinding caused by a damaged agitator

• Unplug the washer and turn off water supply; wear cut-resistant gloves
• Remove the dispenser/cap if present, then the inner cap; take out the retaining bolt or nut
• Lift the old agitator straight up; if stuck, rock it gently to free it without damaging the tub
• Align the new agitator with the drive splines, press down fully, reinstall fastener and cap, then run a short cycle to ensure proper agitation

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed

This transmission and support assembly drives and stabilizes the wash basket. It converts motor power into agitation and spin while supporting the tub, helping resolve no-agitate/no-spin complaints and loud operation for reliable cleaning performance.

• Transfers motor power to the drive system for agitation and spin
• Supports the basket and helps maintain alignment during operation
• Helps correct no agitate, no spin, or weak/intermittent spin
• Can address grinding/rumbling noises or oil traces from the center

• Disconnect power and water before servicing; wear gloves and eye protection
• Appliance and assembly are heavy—use assistance and protect flooring
• Removal typically requires accessing from top and bottom to remove agitator/basket and drive hardware
• After installation, run a test cycle to ensure smooth agitation, proper spin, and no leaks

This front suspension rod assembly supports and stabilizes the washer tub from the front side, helping control vibration and keeping the basket centered for smooth spin and wash performance.

• Supports the tub from the front to maintain proper alignment
• Helps reduce excessive vibration, banging, or walking during spin
• Can address shaking, out-of-balance loads, or tub leaning forward
• Restores proper suspension when the original rod or spring is worn or broken

• Unplug the washer and shut off water before servicing
• Access typically requires lifting the top or removing the cabinet/front panel
• Support the tub while swapping the rod to prevent sudden drop
• Replace in matched positions; inspect other suspension rods for wear

This control knob assembly lets you select cycles and settings on your dryer. Replacing a cracked or stripped knob restores firm engagement with the timer or selector so you can set, start, and adjust drying reliably.

• Attaches to the control shaft to turn the timer or selector
• Provides a secure grip and pointer to choose cycles and options
• Restores proper control when the original knob is cracked or the hub is stripped
• Typical symptoms: knob spins without turning the shaft, feels loose, falls off, or is missing

• Disconnect power to the dryer before servicing
• Pull the old knob straight off; note the shaft shape and orientation
• Align the new knob with the flat/D-shaft and press until fully seated
• If your model uses a separate dial ring or clip, transfer it from the original

This rear suspension rod assembly supports the washer tub from the back of the cabinet. Replacing a worn or broken rod restores stable spin performance and helps reduce banging, vibration, and off-balance interruptions.

• Supports and stabilizes the wash tub from the rear of the cabinet
• Absorbs tub movement during agitation and spin to minimize vibration and noise
• Helps maintain tub alignment to reduce off-balance pauses or repeated redistributions
• Typical symptoms include loud banging, excessive shaking/walking, or the tub leaning toward the back

• Disconnect power and water; wear gloves and eye protection
• Open the cabinet or raise the top to access the rear suspension
• Support the tub to relieve tension, then remove and replace the rod in the same mounting points
• Level the washer and run a short test cycle after replacement