Gtup270gh1ww Parts

This gas conversion kit adapts select 27-inch GE gas dryers to the correct fuel type, helping ensure safe, efficient burner performance when switching between natural gas and LP (propane) after a move or service change.

• Enables fuel-type conversion between natural gas and LP (propane), per your model's instructions
• Restores proper burner pressure and flame for safe, efficient drying
• Useful when relocating to a home with a different gas supply
• Help address weak heat, long dry times, or sooting caused by an incorrect fuel setup

• Installation must comply with local codes
• Disconnect electrical power and shut off gas supply before service
• Follow the model-specific OEM instructions exactly for adjustments and component changes
• After conversion, leak-test all connections and verify proper ignition and flame characteristics

This CCMR 30-amp, 120-volt fuse protects the appliance's electrical circuit by opening when current exceeds safe limits. Replace a blown fuse to restore power to the affected circuit and help prevent damage to internal components.

• Provides overcurrent protection for the circuit specified by the manufacturer
• If the fuse is open, the appliance may be dead, won't start, or certain functions won't operate
• Helps prevent wiring and component damage from shorts or overloads
• Repeated fuse failures indicate an underlying electrical issue requiring diagnosis

• Disconnect power to the appliance before servicing
• Locate the fuse in its holder/block and inspect associated wiring for heat or damage
• Test the old fuse for continuity; replace only with the identical rating specified
• Never bypass or upsize a fuse; correct the root cause of the failure before returning to service

This replacement blower wheel for a dryer mounts to the drive motor and pulls air through the drum, lint filter, and exhaust, restoring proper airflow so loads dry efficiently and the appliance runs as intended. What it does:

• Spins with the motor to move air through the drum, lint screen, and exhaust duct
• Maintains airflow needed for even drying and temperature control
• Wear, cracks, or a stripped hub can cause long dry times and weak vent airflow
• Damage or imbalance may produce rattling, scraping, or vibration noises from the blower area

• 1 blower wheel

• Disconnect power; turn off gas supply for gas models before servicing
• Access the blower housing and remove the old wheel from the motor shaft per your model's design
• Clean lint and debris from the blower housing and exhaust duct while open
• Seat the new wheel fully and verify free rotation without rubbing before reassembly

This electronic control board manages the washer's core cycles and settings. When it fails, the machine may not start, respond to inputs, or complete cycles reliably. Replacing it restores proper control of wash operations.

• Directs cycle selection, timing, and motor/valve operations
• Can lead to erratic behavior such as random stopping or incorrect cycle progression
• Intermittent or dead display/indicator response can also indicate a failed board

• Disconnect power before servicing; verify capacitor discharge where applicable
• Handle the board by edges; avoid static damage by using ESD precautions
• Transfer any connectors exactly by position; label wires as needed
• After installation, run a test cycle

This replacement kit combines the washer's drive motor with a protective tub shield. It restores agitation and spin performance and helps guard the new motor from splash-related moisture so your washer runs reliably through complete cycles. What it does:

• Provides the mechanical power for the washer's agitation and spin functions
• Tub shield deflects water and debris away from the motor area to reduce moisture exposure
• Helps with symptoms such as no spin or no agitation, a motor that only hums, or a burning odor from the motor area
• Useful when the original motor was damaged by leaks or corrosion

• One drive motor and one tub shield

• Disconnect power and water supply before servicing; wear gloves and eye protection
• Access the motor from the underside/front depending on the model; support the washer securely if tilting
• Move wiring connectors one at a time and transfer any brackets or pulley/belt components as configured on your unit
• Seat the tub shield properly, ensure wires are clear of moving parts, then run a test cycle to check operation and for leaks

This replacement screw secures dryer panels and assemblies, helping prevent vibration and keeping components properly aligned. Use it to replace missing or stripped hardware and restore a solid, factory-tight fit during reassembly.

• Secures panels, brackets, and internal assemblies in the dryer cabinet
• Replaces lost, damaged, or stripped factory screw
• Helps reduce vibration and rattling caused by loose hardware
• Supports proper alignment of parts and a tight fit
• Symptoms can include loose or shifting panels, rattling noises, or gaps

• Disconnect power before servicing; for gas dryers, also shut off the gas supply if moving the unit.
• Match screw length and location to the original during reassembly.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Use the correct driver for your screw head style as used on your model.

This transmission pulley mounts on the washer's transmission shaft and is driven by the belt to power agitation and spin. Replacing a worn pulley restores smooth belt tracking, reduces noise, and helps the tub move correctly.

• Mounts on the transmission shaft and transfers motor power through the drive belt
• Enables proper tub movement during agitate and spin cycles
• Wear or damage can cause squealing or grinding noises, or a burning rubber smell
• May lead to poor/no spin or agitation, or the drive belt slipping off

• Disconnect power and wear gloves; safely tip or raise the washer for bottom access
• Remove the drive belt, then the pulley's retaining hardware; install the new pulley and secure hardware
• Reinstall the belt with correct routing; replace a worn belt at the same time
• Spin the pulley by hand to ensure free movement and alignment before testing

This dryer drive belt wraps around the drum and motor pulley to rotate the drum during the cycle. Replacing a worn or broken belt restores proper tumbling so clothes move freely for even drying.

• Transfers motor power to the drum to enable tumbling
• A worn, stretched, or broken belt can cause the drum not to turn
• May also result in the dryer running but not tumbling
• Visual signs include fraying, cracks, or glazing on the belt

• Unplug the dryer before servicing; allow components to cool
• Access typically requires removing the front panel and/or top panel
• Note the belt routing around the motor pulley and idler before removal
• Inspect drum rollers and idler pulley while the belt is off; replace if worn

This shifter hub connects the drive system to the agitator/spin mechanism in the washer, allowing the machine to shift between wash and spin modes reliably for proper cleaning and water extraction.

• Transfers motor/gearcase motion to the basket during spin and to the agitator/wash plate during wash
• Worn or cracked hub can cause no spin, weak/erratic spin, grinding or clicking noises, or poor wash performance
• Designed to fit the original drive components for dependable shifting between cycles

• Unplug washer and turn off water supply before servicing
• Access is typically from the bottom; remove drive components as needed to reach the hub
• Inspect mating parts (splines, clutch/shifter, belt, pulley) for wear and replace if damaged
• Tighten fasteners to spec and verify smooth basket engagement by hand before reassembly

This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.

• Fastens brackets, covers, and sheet-metal panels as specified in the parts diagram
• Restores proper fit when an original screw is missing, stripped, or damaged
• Helps eliminate rattling or vibration from loose hardware
• Keeps components safely in place during operation

• Disconnect power to the appliance before servicing
• Match length, head style, and thread to the original; install in the same location/quantity
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten, especially into plastic or thin sheet metal

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

This selector switch mounts behind the console knob and lets you choose wash settings on your washer. Replacing a worn switch restores reliable selection so the control responds to the setting you intend.

• Allows the user to select a wash option and sends that choice to the timer/control
• Helps when the knob won't click or hold a setting
• Addresses issues where settings don't change or only one option works
• Can resolve dead or intermittent positions on the selector

• Disconnect power before servicing
• Access the control console; remove the knob and the switch's retaining hardware
• Move wire connectors from the old switch to the new one one at a time to maintain correct positions
• Secure the new switch, reinstall the knob, and reassemble the console

The Funnel Shower Head is an OEM part for GE washing machines, designed to distribute water evenly over the laundry during the wash cycle. This component plays a crucial role in ensuring that water and detergent mix effectively, saturating the clothes thoroughly to achieve optimal cleaning performance. The design of the Funnel Shower Head ensures a gentle yet efficient distribution pattern, minimizing the risk of fabric damage while maximizing the removal of dirt and stains.

Causes of a bad Funnel Shower Head can stem from clogging due to mineral deposits from hard water, damage to the part itself, or a blockage caused by foreign objects. 

Symptoms of a bad Funnel Shower Head include:

• Inadequate water distribution during the wash cycle
• Clothes not being fully saturated or washed evenly
• Decreased washing machine performance due to poor water flow

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This water inlet valve assembly regulates the flow of household water into the washer during fill cycles. Replacing it restores consistent fills and helps resolve issues like no water, slow fills, or water leaking into the tub.

• Opens and closes to control water flow into the machine as commanded by the control system
• Helps the washer reach proper fill levels for wash and rinse cycles
• Typical symptoms: no fill, slow fill, fill errors, or water seeping into the tub when the washer is off
• Leaks around the valve or hose connections can also indicate the part has failed

• Unplug the washer and turn off both water supply valves before servicing
• Label hot and cold hoses and take a reference photo before removal
• Expect residual water; use a towel or container. Reconnect electrical connectors and hoses; tighten fittings without overtightening
• After installation, open supply valves and run a test fill while checking for leaks

Size: 10-12 a. Includes 12 screws.

This is a small screw, and it is made for dryers, washers, and washer dryer combos. This is a genuine replacement part made by General Electric. Screws are common in these appliances and can cause many difficulties if they become loose, damaged, or missing.A new screw might be needed if there are areas in the appliance that seem off balance or not level. Another way to tell if a new screw is needed is if there are parts in the appliance that are loose or falling off. This is common over many years of normal use as the shaking of washers and dryers can eventually lead to loose screws. Be sure the washer or dryer is completely off before attempting to replace any screws.This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with washers, dryers, and washer dryer combos made by General Electric.