Gtup270gh1ww Parts

This front suspension rod assembly supports and stabilizes the washer tub from the front side, helping control vibration and keeping the basket centered for smooth spin and wash performance.

• Supports the tub from the front to maintain proper alignment
• Helps reduce excessive vibration, banging, or walking during spin
• Can address shaking, out-of-balance loads, or tub leaning forward
• Restores proper suspension when the original rod or spring is worn or broken

• Unplug the washer and shut off water before servicing
• Access typically requires lifting the top or removing the cabinet/front panel
• Support the tub while swapping the rod to prevent sudden drop
• Replace in matched positions; inspect other suspension rods for wear

This washer motor run capacitor stores and releases electrical energy to help the drive motor start and run smoothly. Replacing a weak capacitor can help restore consistent agitation and spin and reduce motor humming or stalling under load.

• Provides the phase shift and torque assist the drive motor needs to start and stay running
• Can address: washer won't start, no agitate or spin, motor only hums/buzzes, or stops under load
• Visible clues of failure can include a swollen, cracked, or leaking capacitor case

• Unplug the appliance before servicing; capacitors can retain a charge even when power is off
• Discharge the capacitor safely before handling
• Note wire positions; move leads to the same terminals and secure the capacitor in the original bracket/orientation
• Inspect connectors and replace any burnt or loose terminals to ensure a tight fit

This rear suspension rod assembly supports the washer tub from the back of the cabinet. Replacing a worn or broken rod restores stable spin performance and helps reduce banging, vibration, and off-balance interruptions.

• Supports and stabilizes the wash tub from the rear of the cabinet
• Absorbs tub movement during agitation and spin to minimize vibration and noise
• Helps maintain tub alignment to reduce off-balance pauses or repeated redistributions
• Typical symptoms include loud banging, excessive shaking/walking, or the tub leaning toward the back

• Disconnect power and water; wear gloves and eye protection
• Open the cabinet or raise the top to access the rear suspension
• Support the tub to relieve tension, then remove and replace the rod in the same mounting points
• Level the washer and run a short test cycle after replacement

Door gasket seals the door assembly to limit air leaks and keep heat and moisture inside the drum. Replacing a worn gasket restores airflow, improves drying performance, and reduces lint and warm air escaping at the door.

• Forms a compression seal around the dryer door opening/window to prevent air leaks
• Helps maintain proper drum temperature and airflow for efficient drying
• Replace if the gasket is torn, flattened, brittle, loose, or missing
• Helps with: warm air or lint escaping at the door, longer dry times, door rattle, visible wear on the gasket

• Disconnect power; for gas models, also shut off the gas supply and allow the dryer to cool
• Remove the door and separate inner/outer door panels as needed; note gasket routing/orientation
• Clean mating surfaces; install the new gasket without stretching and seat it evenly around the perimeter
• Reassemble and verify an even seal around the door; run a short test cycle to check for leaks

This valve regulates the flow of water into your washer during each cycle. Replacing a failing valve restores proper fill rate and temperature selection to help prevent long fills, no fill, or leaks from a valve that won't close.

• Opens and closes to supply water to the tub when the control calls for fill
• Delivers hot and/or cold water based on the selected temperature setting
• Common symptoms of failure: no fill or very slow fill
• Water dripping into the tub when the washer is off, or leaking around the valve
• Incorrect water temperature during fill

• Disconnect power and turn off both water supplies before servicing
• Place a towel or pan to catch residual water; carefully disconnect hoses
• Note hose and wire positions; transfer connectors to the new valve one at a time
• Restore water and power, then check all connections for leaks and run a quick fill test

This locking clip secures a mating component inside the washer, keeping it firmly attached to its mounting point. Replacing a worn or missing clip restores a snug fit and helps prevent movement, intermittent connections, and noise during operation.

• Retains the designated component securely to its bracket or panel
• Helps prevent vibration-related movement, rattling, or disconnection
• Maintains proper alignment for consistent operation
• Typical signs of failure: cracked or missing clip, part won't stay seated, new looseness around the mount

• Disconnect power and turn off water before servicing
• Access the clip location per your model's service information
• Release and remove the old clip; inspect the mating part for damage or wear
• Seat the new clip fully until it locks; verify the component is secure before reassembly

This electronic water level pressure switch senses air pressure from the wash tub and tells the control when to start and stop filling. Replacing a failed switch restores proper fill levels and helps cycles advance reliably. What it does:

• Monitors tub water level via an air hose connected to the switch
• Signals the control to start/stop the inlet valves at the correct level
• Enables cycle progression by confirming empty/full status
• Common symptoms: won't stop filling, stops filling too soon, incorrect water level, or water-level error codes

• 1 electronic pressure switch

• Disconnect power and turn off water supply before servicing
• Access the switch in the control console or rear cabinet area (location varies by model)
• Move the pressure hose and wire connector(s) over one at a time; ensure airtight hose fit and proper routing without kinks
• Inspect the hose and air dome for cracks, kinks, or blockages; clear or replace if needed

This replacement cover fits the washer's front service door. It restores a clean, finished look and helps shield the service compartment from dust and debris when the original cover is cracked, loose, or missing.

• Covers the service opening to protect internal components from debris and accidental contact
• Restores cabinet appearance by concealing the service area
• Replaces a broken, warped, loose, or missing cover
• Common symptoms: cover won't stay closed, visible cracks, rattling, or a missing access cover

• Disconnect power and turn off water before servicing
• Remove the damaged cover
• Align the new cover with the existing hinge/tabs and secure per your model's configuration
• Confirm proper closure and clearance before restoring power

This spring cover protects and retains a mechanism spring inside your washer. Replacing a cracked or missing cover helps keep the spring seated, limits debris intrusion, and supports smooth, reliable movement of the associated control, latch, or linkage.

• Shields the spring and helps keep it properly seated in its pocket
• Reduces friction and wear that can lead to premature spring failure
• Supports consistent return action for the related control, latch, or lever
• Typical symptoms include a missing/broken cover, exposed spring, rattling, or erratic operation

• Unplug the appliance and turn off water before servicing
• Access point varies by model; photograph spring/cover orientation before removal
• Control the spring during disassembly to prevent sudden release
• Ensure the cover is fully seated; test operation before final reassembly

This electronic control board assembly is the washer's central controller, managing cycle selection, timing, and communication with key components. Replacing a failed board can restore proper operation and dependable cycle performance. What it does

• Interprets user inputs and sensor signals to run wash, rinse, and spin sequences
• Sends power and control signals to the motor, drain pump, water valves, and lid/lock as designed
• Controls cycle timing, speeds, and status indicators
• Symptoms may include: washer won't power on or start, unresponsive controls, cycle won't advance or stops mid-cycle, or error codes/blinking lights

• One electronic control board assembly

• Disconnect power before servicing; verify no voltage is present
• Handle the PCB by the edges and use ESD protection
• Photograph/label wiring; transfer connectors to the new board one at a time
• Secure the board in the original mounts; some models may require configuration per service instructions

This adjustable leveling leg supports and stabilizes your washer. Replacing a worn or missing foot helps the appliance sit flat on the floor, reducing rocking, vibration, and noise for smoother, safer operation. What it does:

• Threads into the base to set height and level the cabinet
• Provides a stable contact point with the floor to minimize movement
• Helps address excessive vibration, rattling, "walking," and out-of-balance issues when the washer isn't level
• Direct replacement for a damaged or missing leveling leg

• 1 leveling leg

• Disconnect power and water before servicing; move the appliance carefully to access the foot
• With assistance, tip or raise the unit as needed to reach the leg safely
• Unscrew the old leg; thread in the new leg by hand and adjust until the washer is level front-to-back and side-to-side
• Tighten the lock nut and recheck stability; run a test cycle to verify

Bleach funnel directs liquid bleach from the washer dispenser into the wash tub for even distribution and helps reduce spills, pooling, and bleach odor. Designed to replace cracked, clogged, or worn dispenser funnels. What it does:

• Directs bleach into the wash tub for consistent dispensing and mixing during the wash cycle.
• Helps prevent bleach pooling, dispenser leaks, and blockages that can cause odors or uneven bleaching.
• Replaces damaged or deteriorated funnels; common symptoms include visible cracks, leaking, or persistent bleach residue in the dispenser area.

• Disconnect power to the appliance before servicing to reduce risk of shock or injury.
• The funnel typically seats or snaps into the dispenser housing.
• Inspect and clean surrounding dispenser components before installing the new funnel; rinse the part to remove any manufacturing residue.
• Handle concentrated bleach with care—wear gloves and follow bleach safety instructions.

This washer strap assembly secures and stabilizes the component it anchors, helping control movement and noise during operation. Replacing a worn or broken strap restores proper support for smoother, quieter cycles.

• Retains and supports the attached part within the washer cabinet
• Helps limit vibration and movement, especially during spin
• Reduces rattling and knocking noises caused by loose or missing restraints
• Visual cracks, stretching, or breakage indicate it's time to replace

• Disconnect power and shut off water before servicing
• Access location per your model's service/repair guide (often requires lifting the top or removing the front panel)
• Support the component being secured while transferring/replacing the strap
• Verify secure attachment points and even support before test running a cycle

This support sensor board is the OEM electronic interface that links appliance sensors to the main control, restoring reliable sensor reporting and helping stop sensor-related errors or intermittent operation after a failed board. What it does:

• Routes sensor signals to the main control so readings are interpreted correctly
• Supports normal sensor communications and helps prevent intermittent or erratic behavior
• Common symptom linkage: sensor error codes, incorrect or fluctuating sensor readings, or intermittent unit operation
• Used as a direct replacement for a failed or damaged sensor interface board

• Disconnect power to the appliance before starting any work to avoid shock or injury
• Ground yourself and avoid touching circuit traces or connector pins to prevent ESD damage
• Verify connector seating and routing of any harnesses; re-check connections before restoring power

This replacement drum assembly restores the rotating drum that holds and tumbles clothes in your dryer, helping return smooth operation and reduce rubbing or scraping noises. Designed as a direct-fit service part when matched to your model. What it does:

• Houses and supports clothes while rotating during dry cycles to enable tumbling and even drying.
• Provides a smooth, durable surface to prevent clothes from catching or rubbing against the cabinet.
• Maintains correct drum alignment so the belt and rollers run smoothly.
• Common symptoms indicating a worn drum: loud scraping or grinding, visible drum wobble, or clothes that don't tumble properly.

• Disconnect power (and gas for gas dryers) before beginning any service.
• Retain original mounting hardware; additional fasteners or seals may be required if not supplied.

Package of 12