Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Drive pulley mounts to the washer basket shaft and routes the belt from the motor. Replace if worn, cracked, loose, or showing play on the shaft.
Replaced the shaft & mode shifter assembly. Also replaced the pulley as it had taken some damage from the wobbling clutch dog. And replaced the tub seal since it's normally inaccessible with the shaft in place. This is an advanced repair that took a lot of time. Removing the tub nut took a 1 11/16" socket and a 700 ft-lb impact wrench and I had to hammer on the nut for several minutes to break it free of the tub. Disassembly of the washer is complete, and requires a lot of space for... Read more
Seals the flood/overflow hose connection to your washer tub. Replace if water seeps from the tub area or the gasket feels soft. Confirm fit by model.
Pulled front panel off. Unbolted and removed top cover. Removed tub trim cover. Removed and replaced gasket and dampers. Put it a back together took about 20 minutes Read more
Connects washer outer tub to drain pump, channeling water out during drain cycle. Replace if cracked, leaking, deteriorated, or damaged by pests.
Simply open the top of the washer by inserting a putty knife (watch YouTube ) and then the front panel by removing two bottom philips head screws on the front. The whole front panel comes right off. Using pliers the spring clams holding each hose, they come off and each hose is replaced. The drain one was only leaking but since it has open I changed both and even the drive belt. Whole job less than 1 hour. BTW parts arrived next day! Read more
Secures the washer's inner basket to the drive hub, keeping the tub centered and stable during spin. Replace if cracked, corroded, or bolts are damaged.
The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more
Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
Seals between the outer tub and splash guard to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the cabinet. Confirm fit by model number.
I tore into the washer until i found what i thought was the problem which was the upper outer tub splash cover gasket and when i couldnt find one in my town i ordered a new one from u folks and replaced it hoping for the best and was successful. This fix costed me $35 instead of the $400+ for a new washer glad i looked into it instead of discarding it and buying a new one as most may do thanks Read more
Fix leaking or noisy washer drums caused by broken trunnion bolts. This fastener secures the trunnion assembly to prevent water leaks and vibration.
Replacement mounting screws for washer cabinet panels, tub straps, and control assemblies. Sold in 12-pack. Replace stripped, rusted, or missing screws.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
Replacement suspension spring for washer tub support systems. Restores proper tension when original spring is weakened, broken, or causing tub tilt.
Watched a few of your videos and ordered the springs and a insert, and actually got the parts right. I am not a Appliance repair guy but I am retired and I am pretty handy so I thought what the heck. I watched the videos, a lot of common sense, common tools, and plenty of time. My knuckles are busted up and a little blood, but I got it done. Was actually kind of rewarding. Works like a champ. The Videos, ARE AWESOME. Read more
Secures control knobs onto shafts in top-load washers. Replace when knobs slip or fall off to restore proper fit and operation. Verify compatibility.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Replaces stripped, rusted, or missing #10-16 screws that secure cabinet panels, brackets, and internal components in washers and dryers.
Googled the problem, watched videos on Youtube. Took apart machine and tried cleaning filter most people said was the problem. Wasn't anything but a penny in it so that wasn't the problem. I decided the pump must be bad ,the spring for the bellows and the console were broken so I bought those as well. Got the parts put them on and machine filled up with water turned over a few times and then stopped. The only thing else it could be is the fill level sensor or the main circuit board. Ordered... Read more
Cushions where the washer lid meets the top panel to soften closure and protect the finish. Replace worn, cracked, or missing bumpers to reduce noise.
The problem was most likely the evaporator fan motor but it could have been a bad blade, loose parts or bad motor mounts. Hard to tell without taking everything apart and inspecting. Since fridge was 17 years old I decided to order the entire evaporator fan assembly as shown in the parts diagram including fan blade, motor brackets, motor, motor mounts, screws, etc. Getting to the assembly involved removing the ice maker unit plus the entire rear inside of the freezer section. Parts cost around... Read more
Washer won't spin or agitate? This drive motor restores drum rotation when your washer hums but won't run or has a burning smell. Moderate DIY repair.
Replaced the motor, capacitor, and belt. Read more
Adjustable leveling leg threads into washer base to stabilize cabinet and reduce vibration. Replace if cracked, broken, or missing for proper support.
Took the old leveling legs out and put the new ones in Read more
Spacer that positions and cushions the agitator screw in top-load washers. Replace if worn, cracked, or missing to maintain proper agitator alignment.
The repair guy told me if I have him fix it I should just buy a new one. I like my washer and dryer because it's a combo and takes up little space so I decided to fix it myself. Not sure if I got lucky but appliance parts pros had a video with almost my exact washer which made repair very easy. Read more
Washer won't start or advance to spin cycle? A broken lid strike prevents the lock from engaging. Simple 5-minute snap-in fix—just remove two screws.
It took less than 5 minutes to fix it. It was very simple, the part fit perfect. I will keep this web site in my favorites for later use. Read more