Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Refrigerator warm but freezer cold? Frosted evaporator coils indicate a failed defrost thermostat. This harness restores proper defrost cycles.
Replaced the defrost thermostat and heater and the refrigerator was working again. Read more
Refrigerator shelf frame that supports glass or wire shelves inside the fridge. Replace if cracked, broken, or warped to restore proper shelf support.
No instructions are included with either piece, which makes installation take more time and care. Tools needed: Small standard flat blade screwdriver, box knife or other knife with at least a 2" long blade, super glue. Remove the old main crisper frame: 1. Remove old main frame by lifting upward and outward. 2. Remove the center rail from the frame. May require bending of the main frame to remove it. 3. Remove the crisper front panel by unsnapping from frame. This is easily done by... Read more
Replace your cracked or broken refrigerator drawer glide. Mounts to the interior wall to support smooth drawer sliding. Essential for worn or damaged glides.
Ordered and installed new ones. Read more
Drawer glide for refrigerator deli or crisper drawers. Replace if cracked, broken, or causing drawer to stick or fall out when opened. Mounts to shelf.
Seals freezer door to prevent warm air entry and maintain optimal temperature. Replace if worn, cracked, or causing frost buildup. Confirm fit by model.
Purchased replacement door gasket (seal). Pulled old gasket from its groove around door. Easily pressed the replacement gasket into the empty groove. Repair complete. Read more
Fix a noisy or non-cooling refrigerator with this condenser fan motor. Solves overheating compressor issues. DIY-friendly repair with video guide.
I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more
White acrylic spray paint for appliance exterior touch-ups. Restores worn, chipped, or scratched surfaces on refrigerators, ranges, and more. 13 oz can.
Replaced It With New One Read more
Covers the base of your refrigerator to protect the lower ventilation area. Replace if cracked, broken, or missing. Snaps into place in minutes.
Called in. Talk to a sale rep. Told them the model number, told me that this part would work. Shipped it to me. Snapped it in about 30 seconds. Part was perfect. Read more
Touch-up paint for covering scratches, chips, and minor blemishes on appliance exteriors. Restores appearance and protects surfaces when finish is damaged.
Touch up paint Read more
Glass panel that covers the top of crisper drawers in your refrigerator. Replace if cracked, shattered, or broken during cleaning or normal use.
Ordered the piece and put it in the refrigerator. Read more
Refrigerator making noise or not cooling? A broken condenser fan blade prevents air circulation. This friction-fit part installs in minutes—no tools needed.
I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more
Mounting screw for refrigerator ice maker assembly. Secures components to maintain structural integrity. Replace if lost, stripped, or corroded.
Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more
Gray door closer cam for bottom-mount refrigerators. Installs at the hinge to enable smooth closing and door stay-open function. Replace if cracked or worn.
Replaced door closure and door stop. Read more
Ice maker not working or won't make ice? Failed wiring harness disrupts power to the ice maker. DIY-friendly repair, installs in minutes with basic tools.
I watched the video on how to replace the ice maker and the replaced it with zero problems. Excellent help in trouble shooting problem and installation video further assisted in ease of installation. Read more
Freezer evaporator coil icing up and refrigerator not cooling? This defrost thermostat regulates temperature to prevent frost buildup. 2-3 hour DIY repair.
My unit has a bottom freezer that is a drawer. I had to remove the drawer, rack, glides, glide tracks, and ice maker to remove the rear panel. This was a little difficult but after researching a few videos on line I learned some tricks that made it easier. I used a hair dryer to melt the ice. This is best done with 2 people having one at the back to sponge the water into a bowl from the pan to avoid a water mess. Using a bolt meter I checked the heating element and found it had continuity. I... Read more
Replacement crisper pan for refrigerators. Installs in the fresh food section to store fruits and vegetables. Replace if cracked, broken, or missing.
Replacement of parts found on this site- great explanation and pictures as shown! Read more