Jcd2396g Parts

This rubber boot seals and shields a component or connector within the appliance. Replacing a worn boot helps keep out moisture and debris, preventing corrosion and wear so the protected part continues to operate reliably.

• Provides a protective seal around the targeted connection or component
• Helps keep out moisture, dust, and debris
• Minimizes vibration and abrasion at the connection point
• Direct replacement when the original boot is cracked, brittle, torn, or missing
• Symptoms can include visible damage, loose fit, or signs of moisture/rust near the protected area

• Disconnect power and turn off water supply before starting
• Access the area and note the boot's orientation and seating depth
• Remove the old boot; fully seat the new boot and transfer any reusable clips/covers
• Restore power/water and verify a secure seal and normal operation

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

The Water Tube is an OEM component specifically designed for Whirlpool refrigerators. This 1/4" diameter water tube provides a pathway for water to flow through the refrigerator's internal components during operations like ice production. 

Causes of a bad water tube can include cracks or defects from manufacturing, damage from impact or abrasion during shipping or installation, or wear over time from cycles of use.

Symptoms of a bad water tube include:

• Water leaks or drips inside the refrigerator 
• Insufficient or slow water flow to components
• Abnormal sounds from water not flowing smoothly
• Failure of components dependent on water flow like the ice maker

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore refrigerator models.

This top coupling links two drive components in select washers to transfer rotation smoothly. Replacing a worn or stripped coupling restores consistent agitation/spin and can reduce slipping, rattling, or grinding noises from the drive area. What it does:

• Connects mating shafts/components so power is transmitted through the drive system
• Helps maintain alignment and cushions minor shock to protect other parts
• Failure symptoms may include no or weak agitation/spin, intermittent drive, or clicking/grinding sounds
• Visual clues can include cracks, rounded/stripped splines, or excessive play

• One top coupling

• Disconnect power; turn off water supply if moving the appliance
• Access location varies by model; cabinet/top or front panel removal may be required
• Note orientation of flats/splines and seat the coupling fully—do not hammer into place
• Inspect the mating hub/shaft; replace worn companion parts to prevent rapid re-wear

The Water Filter Cap is an OEM replacement part for Whirlpool refrigerators. This component is a decorative cover that fits over the water filter, providing a neat and finished appearance to the filter housing area.

Color: Grey

Over time, the water filter cap can become damaged due to accidental impact, routine handling, or regular wear and tear. 

Symptoms of a faulty water filter cap include:

• Difficulty in securely fitting the cap onto the water filter
• Cracks, discoloration, or missing pieces
• An unsightly internal refrigerator appearance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This smart electronic water inlet valve controls the flow of fresh water into the dishwasher during each cycle. Replacing a weak, leaking, or stuck valve restores proper fill performance and helps prevent no-fill, slow-fill, or unintended filling. What it does:

• Opens and closes under control of the electronic board to admit water at the correct time
• Regulates incoming water so the tub fills to the proper level for each cycle
• Failure symptoms can include no fill or very slow filling
• May allow water to seep into the tub when off, or leak from the valve body/fittings

• 1 water inlet valve assembly

• Disconnect power and turn off the water supply before servicing
• Place a towel or tray to catch residual water; depressurize the supply line
• Move the wiring connectors one at a time to the new valve to avoid miswiring
• Restore water and check all connections for leaks; run a fill test to verify operation

This crisper pan is the refrigerator's produce drawer. It replaces a cracked or missing bin to restore a clean, dedicated space for fruits and vegetables and smooth slide-in/slide-out access in the fresh food section. What it does:

• Provides a dedicated compartment to organize produce in the fresh food compartment
• Helps contain spills to protect shelves and liners below
• Slides on the factory rails for easy access and removal
• Common failure signs: cracks, chips, warping, staining, or a drawer that won't slide or stay on its tracks

• 1 crisper pan

• Disconnect power to the refrigerator before servicing
• Empty the old bin and slide it straight out of the tracks
• Clean and inspect tracks/rollers for debris or damage before installing
• Align the new pan with the tracks and slide it fully in; do not force

The Whirlpool latch spring is an OEM replacement part responsible for securing the ice container or bin in place on a refrigerator. Its main function is to provide tension and support to the ice container latch, allowing it to engage and disengage properly. When the ice container is inserted into the refrigerator's ice compartment, the latch spring ensures that it securely locks in place, preventing accidental spillage of ice.

Causes of a bad latch spring can include metal fatigue from repeated use, rust or corrosion from exposure to moisture, or physical damage from accidental impacts.

Symptoms of a bad latch spring include:

• The ice container not staying in place and sliding out of position
• Difficulty in properly attaching or detaching the ice container from the refrigerator
• The ice container feeling loose or wobbly when inside the ice compartment
• The ice container not aligning correctly with the ice dispenser or auger

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 8 x 1/2 ab.

The Door Chute is an OEM part for Whirlpool refrigerators. This part directs ice from the ice maker into the ice bucket or dispenser chute. The door chute ensures a smooth and controlled flow of ice, preventing spills and maintaining the efficiency of the ice dispensing system.

Common issues include cracks, warping, or blockages that can obstruct the flow of ice and affect the dispenser's performance.

Symptoms of a bad door chute include:

• Ice not dispensing properly
• Ice jamming or clogging in the chute
• Leaks or drips around the ice dispenser area
• The door chute not sealing correctly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Shelf Stud is an OEM part for Whirlpool refrigerators. It serves as a support peg that holds the refrigerator shelves in place, ensuring they remain stable and properly positioned.

Causes of a bad shelf stud can include wear and tear from regular use, accidental impact that causes the stud to break, or repeated removal and reinstallation of shelves leading to loosening or damage.

Symptoms of a bad shelf stud include:

• Shelves not staying securely in place
• Shelves tilting or collapsing
• Visible cracks or damage to the stud
• Difficulty in inserting or removing shelves

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a rear stud with a screw. For the front stud with screw use part number W11223328. For studs with no screw use kit part number 4388538.

Clip for bottom grill. If your original clip is riveted, order screw WP489478.

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This ice maker cover fits over the ice maker head to protect the control module and moving parts inside your freezer. Replacing a cracked or missing cover helps prevent frost intrusion and restores a clean, finished look.

• Shields the ice maker mechanism from debris and moisture
• Helps maintain airflow to reduce frost at the ice maker face
• Replaces a cracked, warped, or missing cover with broken tabs
• Can help address exposed gears/wiring or rattling from a loose cover

• Disconnect power to the refrigerator before servicing
• Remove the ice bin to access the front of the ice maker
• Release retaining tabs or screws and remove the old cover
• Align and snap the new cover fully into place; verify it's secure and clear of moving parts

This part is the dispenser ice door support. It mounts and aligns the ice chute flapper (ice door) in the freezer door so it pivots and seals correctly, helping reduce warm air leaks, frost, and ice clumping. What it does:

• Provides the pivot/mount for the dispenser ice chute door (flapper)
• Keeps the ice chute door aligned to help maintain a proper seal
• Wear or broken tabs may cause the flapper to stick open/closed
• May lead to frost in the chute, condensation, air leaks, or clumping ice

• 1 ice door support

• Unplug the refrigerator and remove the ice bin before servicing
• Remove dispenser trim/control to access the chute assembly
• Note spring and flapper orientation; transfer the door, seal, spring, and any hardware to the new support
• Verify smooth flapper movement and full seal before reassembly and restoring power