Kdte140dss0 Parts

Color: Stainless   Note: Comes with Allen wrench, spare set screw, and instructions.

This part is the rinse-aid cap/knob that seals the dishwasher's rinse-aid reservoir in the door-mounted dispenser. A secure cap prevents leaks and evaporation so rinse aid dispenses properly, helping reduce spots and improve drying.

• Seals the rinse-aid fill port on the dispenser to prevent leaks and evaporation
• Helps the dispenser meter rinse aid during the final rinse
• Common symptoms of a bad/missing cap: loose or cracked cap, rinse-aid odor or residue inside the door, rinse aid depleting quickly, increased spotting on dishes
• Restores proper sealing and helps maintain consistent drying performance

• Disconnect power at the breaker and turn off water before servicing
• Open the door, remove the old cap by turning counterclockwise
• Clean the sealing surface; install the new cap by hand and tighten until snug—do not overtighten
• Run a quick cycle and check for leaks around the dispenser

This cup shelf clip secures the dishwasher's fold-down cup shelf to the upper rack. Replacing a cracked or missing clip restores a stable shelf so cups and small items stay organized throughout the wash cycle.

• Fastens the cup shelf to the upper rack wire to prevent wobble or detachment
• Helps the shelf pivot and lock properly when raised or lowered
• Typical symptoms: shelf hangs loose, falls off, won't stay in position, or the original clip is broken/missing

• Open the door and fully extend the upper rack; remove the rack if needed for access
• Squeeze the old clip's tabs to release and lift it off the rack wire or shelf
• Align the new clip on the rack wire and press until it snaps securely into place
• Verify the shelf moves and locks correctly before running a cycle

This electronic control board is the appliance's central controller, managing critical functions and timing. Replacing a failed board restores proper operation, responsive controls, and consistent performance when the unit is unresponsive, shows errors, or behaves unpredictably.

• Processes user commands and internal signals to run cycles as designed
• Controls or communicates with motors, valves, fans, and heaters through onboard components
• Manages timing, temperatures, and safety checks programmed by the manufacturer
• Symptoms of failure: won't power on or start, dead or erratic controls, error codes, intermittent operation

• Disconnect power to the appliance before servicing; also shut off gas/water
• Use anti-static precautions and handle the board by its edges
• Photograph connections; transfer connectors one at a time to the new board; secure in the original mounting
• After installation, follow your model's tech sheet for any required initialization/diagnostics and verify normal operation

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This compression tube nut secures water inlet tubing to a threaded fitting to create a reliable, leak-resistant seal. Replace a cracked or stripped nut to stop drips at the connection and keep your appliance's water system working properly.

• Compresses the tubing against the fitting to seal the water line at the inlet valve, filter head, or other water-system connections
• Helps correct leaks at the water line connection point
• Replaces nuts that are cracked, cross-threaded, or deformed
• Common symptoms: water dripping at the connection, difficulty tightening the line, or a poor seal after reassembly

• Shut off the water supply and disconnect power before servicing.
• Slide the nut onto the tubing first, seat the tube fully on the fitting, then hand-tighten and snug with a wrench; do not overtighten.
• Inspect and reuse the existing sleeve/ferrule and tube insert if in good condition; replace if worn.
• Restore water and check for leaks at the connection.

The door balance mount is the side-frame bracket that supports the dishwasher's door counterbalance system. When worn or broken, it can let the door drop, slam, bind, or feel heavy. Replacing it restores smooth, controlled door movement. What it does

• Anchors the door springs and balance link/cable to counterbalance the door's weight
• Helps the door open and close smoothly without dropping or slamming
• Guides the balance link for consistent, quiet movement
• Common symptoms: door feels heavy or uneven, falls open, won't stay put, or makes grinding/squeaking noises; visible damage to the bracket or rollers

• One door balance mount (bracket)

• Disconnect power and shut off water before servicing
• Pull the dishwasher out slightly to access the side where the mount is installed
• Carefully relieve spring tension; note link/cable routing before removal
• Transfer the spring/link to the new mount, secure the bracket, and check door balance on both sides

This replacement screw secures appliance panels, brackets, and internal components. Install it when original hardware is missing, stripped, or corroded to restore a solid, factory hold and help stop vibration, rattles, and misalignment.

• Provides secure attachment for covers, brackets, and assemblies
• Replaces missing, damaged, or rusted hardware
• Helps resolve loose panels, buzzing/rattling noises, or shifting parts
• Supports proper alignment and reliable operation when tightened correctly

• Disconnect power; shut off gas/water if applicable before service
• Match thread and length to the original; replace in the same location
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• If washers, spacers, or threadlocker were present originally, transfer or replace them

The Dishrack Stop Clip is an OEM component specifically designed for Whirlpool dishwashers. It secures the sliding dishwasher rack at the rear of the tub.

Symptoms of a faulty stop clip include:

• Dishes shifting position or toppling during cycles of motion  
• Noisy clattering heard from partially-restricted rack movement
• The dishrack failing to fully retract or extend 

Over time, repeated force from dish impacts can bend the thin metal clip out of place. Fatigue causes it to lose retaining strength.

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwasher models.

This inner door seal forms a moisture barrier between the dishwasher tub and the door assembly, helping keep wash water and steam contained. Replacing a worn seal can stop drips at the door and protect internal components.

• Seals the joint along the inner door to contain wash water and steam
• Helps prevent door-area leaks or drips during cycles
• Blocks moisture from entering the door cavity where electrical parts reside
• Common signs: water at the bottom/sides of the door, damp control area, visible wear/flattening or tears on the seal

• Disconnect power and turn off water supply before servicing
• Open the door and remove perimeter screws to separate inner/outer door panels
• Remove the old seal; clean the mounting surface and note seal orientation
• Press the new seal firmly into place, reassemble, and run a leak check

This replacement screw secures appliance components, panels, and brackets. It restores a tight, reliable hold when an original fastener is missing or damaged, helping eliminate rattles, gaps, or shifting parts.

• Fastens two or more parts together inside the appliance
• Helps keep panels, brackets, or trim securely in place
• Can reduce vibration, rattling, or loose handles caused by missing/loose screws
• Replaces worn, stripped, or corroded fasteners

• Disconnect power and shut off water supply before servicing
• Match location and orientation to the original fastener
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to prevent stripping or cracking

The Panel Toe is an OEM part compatible with GE dishwashers. It is a discreet metallic strip located along the bottom front panel of the appliance. The toe provides protection and reinforcement to this high-impact area.   

Causes of a bad panel toe include normal wear from opening and closing the dishwasher door hundreds of times each year. Misalignment from door impact can also cause premature deterioration.

Symptoms of a bad panel toe include: 

• Visible cracking, bending, or detachment of the toe strip
• Potential for other panel issues if toe integrity is compromised
• Possible denting or distortion of neighboring surfaces
• Aesthetic issues and reduced protection of front panel edges

This genuine GE replacement part restores the structure and helps prevent further damage. Compatible Dishwasher models also include some Hotpoint, Profile, and Kenmore units.
 

The Retainer is an OEM part for Whirlpool dishwashers. It securely holds the top spray arm in place underneath the dishwasher interior roof panel.

Causes of a bad retainer include cracking, breaking or deforming from repeated use and natural wear over time.

Symptoms of a bad top spray arm retainer are:

• Loosening or detachment of the upper spray arm during washing cycles
• Reduced or uneven water coverage for upper rack dishes
• Potential rattling or noise from an unsecured spray arm

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This rear support wheel replaces a worn roller that helps a sliding drawer or rack glide smoothly and stay aligned. Restores easy, even movement and reduces dragging, scraping, or tilting during everyday use.

• Supports the rear of a sliding assembly on its track
• Provides smooth rolling action and helps maintain alignment
• Helps prevent binding, popping off the track, or uneven travel
• Replace if the wheel is cracked, flattened, missing, or if movement is noisy or difficult

• Disconnect power before servicing; allow the appliance to cool
• Remove the sliding assembly to access the wheel area
• Transfer or reinstall any axle/retainer from the original wheel as needed
• Verify smooth travel and proper alignment after replacement

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey