Kenmore He2 Mod Parts

This replacement screw secures panels, brackets, and internal components in your appliance. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps keep parts properly aligned and protected during operation.

• Fastens appliance panels, brackets, and hardware in the designated locations
• Replaces missing, stripped, or corroded fasteners
• Helps reduce vibration noise and looseness from unsecured parts
• Restores proper fit and alignment after service or reassembly

• Disconnect power; turn off water supply before servicing
• Match the screw to the original location and replace one at a time to maintain alignment
• Use the correct driver; tighten snugly without overtightening to avoid stripping metal or cracking plastics
• If threads in the mating hole are damaged, repair/replace the clip or insert as specified in the service manual

This drain hose carries used water from the appliance to the household drain. A secure, leak-free drain path helps prevent water from backing up or leaking during and after a cycle.

• Routes wastewater from the unit to the standpipe or sink drain
• Helps resolve issues like slow or incomplete draining
• Can address leaks found around the rear or drain area
• Restores proper water exit flow after hose damage or kinks

• Unplug power and shut off water before servicing
• Have a towel or shallow pan ready to catch residual water
• Note hose routing and connections before removal; transfer any clamps if reused
• Ensure tight, watertight connections and proper routing without kinks

Replacement plug button that snaps into place to cover a small access hole or fastener opening. Restores a finished appearance and helps keep dirt, moisture and small objects out of the appliance cavity. What it does:

• Covers exposed holes or mounting openings for a clean, finished look
• Prevents dirt and debris from entering small internal cavities
• Replaces missing, cracked or worn plug buttons that no longer stay seated
• Small, low-profile design to match factory appearance

• Disconnect power to the appliance before servicing
• Typically installs by pressing into the opening until it snaps flush; a small flat screwdriver can assist
• Avoid prying against surrounding trim to prevent cosmetic damage
• Keep small parts away from children and pets

Color: Almond

This door spring restores the proper counterbalance of the oven door so it opens smoothly and closes with controlled tension. Replacing a worn or broken spring helps prevent the door from dropping, slamming, or sitting unevenly.

• Provides counterbalance tension for the oven door through the hinge mechanism
• Helps the door open smoothly and hold at a partially open position
• Maintains even alignment and consistent gasket contact
• Common symptoms of failure: door feels heavy, drops open or slams, uneven door height, squeaks during movement

• Disconnect power at the breaker and allow the oven to cool completely
• Springs are under tension—support the door and use caution to avoid injury
• Note the spring's routing and anchor points before removal; reinstall in the same positions
• For even tension, consider replacing both door springs when the design uses one per side

Replacement housing that supports and protects internal components in compatible Whirlpool appliances. Restores structural integrity to the cabinet, helping reduce vibration and keeping wiring and components enclosed for safe, reliable operation. What it does:

• Provides the outer cabinet support that secures motors, controls and wiring
• Protects internal parts from debris and accidental contact
• Helps reduce rattling, vibration and misalignment symptoms caused by cracked or damaged cabinets
• Restores proper fit for panels and fasteners to eliminate rubbing or interference noises

• Disconnect power (and water if applicable) before starting any repair
• Basic hand tools are typically required; keep screws and clips organized during disassembly
• Some housings may require two people to position during replacement—avoid forcing parts to prevent damage
• Fasteners and any sealing gaskets are in good condition and replaced if worn

Restore smooth operation of your dryer's lint screen cover with this lint screen door spring. It provides the correct tension so the cover opens and closes properly and the lint screen seats securely for reliable lint collection.

• Applies spring tension to the lint screen door/cover hinge
• Helps the lint screen and cover stay properly positioned
• A worn or broken spring may cause the cover to feel loose, pop open, or not stay closed
• May make inserting or removing the lint screen difficult

• Disconnect power; for gas dryers, also shut off gas supply
• Access the lint screen door area per your model's service information
• Note the original spring orientation; transfer the new spring carefully using needle-nose pliers
• Check cover operation and lint screen seating before restoring power

This factory fastener secures appliance components and panels, helping keep assemblies properly aligned and tight. Replace worn, stripped, or missing hardware to eliminate looseness and vibration and maintain safe, reliable operation.

• Fastens brackets, panels, trim, and internal assemblies to the cabinet/frame
• Helps maintain alignment of doors, consoles, or covers
• Restores a tight fit to reduce rattling, vibration, or shifting
• Common symptoms: missing screw, stripped head/threads, loose panel or handle, recurring vibration/noise

• Disconnect power (and shut off gas/water if applicable) before servicing
• Match thread and length to the original fastener for proper fit
• Start threading by hand to avoid cross-threading; use the correct driver
• Do not overtighten into plastic or thin sheet metal

The lid switch lever connects the washer's lid hinge to the lid switch, signaling when the lid is closed so the cycle can run. A damaged lever can prevent the safety interlock from closing, leading to no-start or spin issues. What it does:

• Transfers lid movement at the hinge to the lid switch actuator
• A closed lid so the washer can operate
• Common symptoms of a failed lever: washer won't start; won't spin; cycle pauses because the lid-closed signal isn't detected

• 1 lid switch lever

• Disconnect power before servicing
• Lift or open the top to access the hinge/switch area; locate the lever near the lid switch
• Remove the old lever and install the new one in the same orientation; free movement
• Close the lid by hand and the switch clicks before reassembly and testing

This replacement screw secures appliance components and panels in their proper position. Replacing worn, stripped, or missing hardware restores a tight fit, reduces vibration or rattles, and helps maintain safe, reliable operation per the manufacturer's design. What it does:

• Fastens panels, brackets, or assemblies where specified in the model's parts diagram
• Replaces missing, rusted, or stripped hardware
• Helps eliminate looseness, rattling, or vibration
• Restores secure alignment of mounted components

• 1 screw

• Disconnect power and shut off water/gas before servicing.
• Verify the exact location in your model's parts diagram and replace screws one at a time to maintain alignment.
• Use the correct driver/bit; start threads by hand to avoid cross-threading and do not overtighten.
• Inspect mating holes/clips for damage; repair or replace related hardware if threads are compromised.

This electronic control board is the appliance's central "brain." It manages power, timing, and communication with sensors and the user interface so programs start, run, and complete as designed.

• Directs power to loads based on cycle logic
• Monitors inputs from sensors and switches to protect components
• Interprets user commands and coordinates cycle timing
• Common failure symptoms include no power/no response or dead display
• Also presents with cycles not advancing, random resets, or recurring control-related error codes

• Disconnect power before servicing; verify no voltage is present
• Use ESD precautions; handle the board by the edges and avoid touching components
• Move connectors one at a time from the old board to the new board; match orientation and latch fully
• Secure the board, restore power, and run model-specific diagnostics or configuration steps per the service manual if required

This retainer clip secures a component in place to prevent movement and maintain proper alignment during appliance operation. Replacing a damaged or missing clip helps restore safe, reliable performance.

• Holds the mating part firmly to reduce vibration and noise
• Helps prevent intermittent operation caused by loose fitment
• Common fix when a component feels loose, rattles, or won't stay seated

• Disconnect power and shut off gas/water before servicing
• Note original clip orientation and location before removal
• Use needle-nose pliers to carefully release and install the clip
• Do not over-bend the clip; replace if deformed or fatigued

This Heater Box Bracket secures the dryer's heater housing to the cabinet, keeping the heating assembly firmly mounted and aligned. Replace a bent, cracked, or missing bracket to restore stable support and reduce vibration around the heater area.

• Anchors the heater housing/box to the cabinet frame
• Maintains proper alignment and clearance for the heating element assembly
• Helps prevent rattling or rubbing noises from a loose heater housing
• A damaged bracket may leave the heater housing loose, cause vibration, or contribute to intermittent heating issues

• Disconnect power; if gas, shut off gas supply and allow the unit to cool completely
• Access the heater housing; note bracket orientation and reuse existing fasteners
• Support the heater housing and keep wiring clear while removing/installing the bracket
• After installation, verify the housing sits square and clear of the drum and wiring before restoring power

This stacking kit secures a dryer on top of a compatible washer to save floor space and stabilize the stacked units. It helps keep the dryer aligned and reduces shifting or rocking during use. What it does:

• Provides a secure connection between dryer and washer to create a stable stacked laundry configuration.
• Helps prevent the dryer from sliding, tilting, or shifting during spin cycles — common signs a stack kit is needed.
• Uses brackets and mounting hardware to fasten the dryer to the washer and maintain alignment.

• Disconnect power to both appliances and follow all safety precautions before starting installation.
• Have a second person assist when lifting or positioning the dryer to avoid injury or damage.
• Follow the OEM installation instructions and torque guidance for mounting hardware; ensure both appliances are level and stable after installation.

Note: This is a kit of 4 shipping bolts.