Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix oil or grease leaking into your mixing bowl with this center shaft kit. Includes shaft, seal, and gasket. Moderate DIY repair for experienced users.
Checked out You tube video. Easy tune up. One gasket was damaged and I did not notice that the brush holders has no brushes. I believe a quick call to Appliance parts pros will fix this, besides I need a few more parts. I expect to get another 20+ years from this KitchenAide mixer, once repairs are competed. Watch out for the single lock washer located on the rear upper housing screw, you don't want to lose this! Read more
Replacement thumb screw for stand mixer power hub. Secures beater, whisk, and dough hook attachments. Replace if cracked, broken, or missing.
After ordering the speed lever, I watched one of the videos about disassembling the mixer. I followed the instructions pretty much to the letter except I found I spent more time cleaning and air dusting around the motor to get the accumulated flour dust out. The insides of the mixer haven't been touched in 30 years. About the most difficult part of disassembly was the 4 screws holding the mixer head to the stationary base. these screws have beveled cuts designed to lock the screws in place, I... Read more
Fix mixer stuck at one speed or won't turn off. This speed link connects to the speed control mechanism. Common DIY repair, takes 30-45 minutes.
Found the broken parts upon disassembly. Ordered new parts. Parts were shipped very quickly. Read more
Replacement lift arm for stand mixers. Supports and raises/lowers the mixing bowl. Replace if cracked, broken, or won't stay in raised position.
I followed the online tutorials, there are many....replaced the PLASTIC part that had worn out Part #: AP4325266 (241764), and also the roll pin, Part #: AP3038054 (9703442) that held it in place with the handle. THIS IS THE HARDEST part of the entire repair, pounding out the roll pin and pounding it back in. A special tool should probably be used for this. I had a small specialized driver bit that "fit" for the job, so I abused it. Probably didn't need to BUY a NEW roll pin, ( it HAS be... Read more
Washer spacer insulates and protects gears in your stand mixer's planetary system. Replace when gears become loose or noisy. Confirm fit with your model.
Watched videos available on APP's website, then ordered all necessary parts. Once parts arrived, just followed the videos again, step-by-step, to repair the mixer. I am NOT a "handyman", but with APP as my resource, I did it. Mixer running great now. Read more
If your stand mixer bowl won't lock or stay in place during mixing, this latch spring secures the bowl properly. Easy 5-minute fix with just two screws.
Ordered replacement and installed Read more
Replacement spring for stand mixer control plate assembly. Maintains tension between speed control lever and plate. Needed when broken, missing, or worn.
This hub cap covers the attachment port at the top of your stand mixer. Replace if cracked, missing, or broken. Simply unscrew and snap on.
I WENT ONLINE AND ORDERED THE PART ON A TUESDAY. IT WAS DELIVERED BY FED EX ON WEDNESDAY. GREAT SERVICE. Read more
Replaces a worn or stripped shaft-and-pinion assembly in your stand mixer. Installs in the geartrain to transfer motor rotation to driven components.
Replaced gear Read more
Replace your worn dough hook if yeast dough isn't kneading properly or sticks to the attachment. Non-stick coating ensures smooth mixing and easy cleanup.
Pouring shield attaches to the top of your stand mixer bowl to prevent ingredient splatter during mixing. Replace if cracked, broken, or missing.
Fiber spacer washer installs on the vertical center shaft between gears in stand mixers. Replace if cracked, worn, missing, or causing loose shaft.
For most 20-year-old KitchenAid Blenders the grease packed inside begins to break down into UCK and oil which will drip through the old gaskets. After breaking down the case and removing all of the old grease and oil I cleaned all the gearing and shafts. I replaced the case gasket, the 2 shaft gaskets that the lower orbital gear slides up, and then the o-ring on the main shaft after everything was installed. I did a break-in run on med speed for one hour and then tapped the chrome ring off... Read more
Replace a worn, bent, or broken agitator shaft in your stand mixer. This shaft connects attachments to the planetary mechanism for proper operation.
REPLACED WORM GEAR AND OTHER GEARS SHOWING WEAR Read more
Replace your stand mixer's power cord if it's damaged, frayed, melted, or chewed. This electrical cord connects your mixer to the outlet for power.
I replaced the Board-Phas and speed control plate since power was not making it to the motor. When I received the speed control plate it had nuts on the upper screws with springs, since my old one didn't have nuts I assumed that the nuts were to keep the springs on until installed. After putting it back together, I noticed that though it worked, the first two settings did nothing. Now, guys, I was desperate, OK. I downloaded the service manual and read it from front to back, and when I got to... Read more
Spacer washer maintains proper spacing between mixer gearcase components. Replace if cracked, worn, or missing to restore correct alignment and operation.
Replacement power cord for stand mixers. Connects your mixer to the wall outlet. Replace if frayed, heat-damaged, cracked, or loose for safe operation.
Took it apart after watching a YouTube video and fixed it with no issues. Works as good as new now Read more