Lfg25760sw Parts

The Overlay is an OEM replacement part for Frigidaire ranges. Its primary function is to cover and label the selection buttons on the control board, thus facilitating easier identification and use. This part does not include any additional components, as it is just the overlay.

Causes of failure relate to repeated exposure to heat and moisture around the range diminishing overlay adhesives over time. Burns or punctures are also possible from cooking mishaps.

Symptoms include:

• Detached or peeling sections exposing internal components
• Discoloration, melting or warping of printed graphics

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Leveling Leg Assembly is an OEM part for Frigidaire ranges. This part provides stability by allowing users to adjust the height of the range, ensuring it is level and balanced on the floor.  

Causes of a bad leveling leg assembly can include wear from frequent adjustments, damage due to heavy loads, or breakage from accidental impacts.  

Symptoms of a bad leveling leg assembly include:

• The range being uneven or wobbling
• Difficulty in leveling the range using the legs
• Noise or movement when the range is in use
• Doors not aligning properly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This valve controls gas flow to a range/cooktop surface burner for smooth ignition and precise flame adjustment. Replacing a worn valve helps restore reliable burner lighting, accurate heat control, and safer shutoff.

• Regulates gas to a surface burner for ignition and flame size control
• Sticking or worn internal seals can cause hard-to-turn operation or gas odor
• Failure may prevent the burner from lighting or shutting off completely
• Inconsistent or unresponsive flame adjustment can indicate a failing valve

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool; access the valve/manifold per your model's instructions
• Mark and disconnect tubing and any wires; transfer fittings or a separate spark switch from the old valve if applicable
• After installation, restore gas and check all joints with an approved leak-detection solution; verify proper burner operation

This burner replaces a worn or damaged unit on your range to restore reliable, even heat. Swap it in to correct poor performance caused by cracks, corrosion, or blockages so cooking results return to normal.

• Provides the heat source for a cooking zone on the range
• Common fix for damage, warping, or clogged ports/passages
• Symptoms include won't light/heat, weak or uneven heating, or irregular/yellow flame on gas models
• Visible rust, cracks, or deformation indicate replacement is needed

• Disconnect power; for gas models, also shut off the gas supply. Allow the appliance to cool completely
• Remove grate/cap or unplug element as applicable; take out screws/retainers to lift off the old burner
• Transfer reusable items from the original part (such as cap, electrode/igniter, and screws) if required by your model
• Align correctly and tighten fasteners evenly; restore utilities and test for proper operation

This ignitor/orifice assembly combines the surface burner spark electrode with the orifice holder that meters gas to the burner. Replacing a worn assembly restores reliable ignition and proper gas flow for steady, even flame performance.

• Provides the spark to ignite surface-burner gas
• Houses the orifice that controls gas flow into the burner head
• Helps resolve burners that won't light or only light with a match
• Can improve weak, uneven, or delayed ignition
• Replaces cracked or carbon-tracked electrodes and corroded orifice holders

• Disconnect power and shut off the gas supply before servicing
• Let the cooktop cool; remove grates, caps, and burner heads to access the assembly
• Disconnect the spark lead and gas connection, install the new assembly, and secure fittings per OEM guidance
• After reassembly, restore gas and check connections for leaks with an approved leak-detection solution; verify ignition and flame

The Knob is an OEM part for Frigidaire ranges and ovens. It is used to control the temperature and settings for the stove's burners or oven functions, providing an interface for selecting heat levels and cooking modes.

You should replace this knob if it becomes damaged or worn out. Common causes of a bad knob include physical damage from impact, wear and tear from frequent use, or melting due to exposure to high temperatures.

Symptoms of a bad knob include:

• Difficulty turning the knob
• Knob slipping or not staying in place
• Cracks or breaks in the knob
• Inaccurate temperature or setting adjustments

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This surface burner cap fits gas ranges and cooktops. It sits atop the burner head to shape the flame and shield the burner from spills, helping restore smooth ignition and consistent, even heat output.

• Shapes and distributes the burner flame for more even cooking
• Protects the burner head from spills and debris
• Helps ensure reliable ignition and a stable, blue flame
• Common signs it's needed: missing/damaged cap, uneven or yellow flames, burner slow to light, rattling cap

What's included: One surface burner cap. Install notes:

• Turn the burner off and allow the cooktop to cool completely before servicing.
• Remove the grate and lift off the old cap; clean the burner head and ports if needed.
• Center the new cap on the matching burner head so it sits level and fully seated.
• Reinstall the grate and test; realign the cap if the flame is uneven.

The Switch Rocker is an OEM part for Frigidaire ranges. This switch is used to control various functions of the range, such as turning on heating elements or activating specific cooking modes. It provides a reliable and straightforward interface for managing the range's features.

You should replace the range switch rocker if it becomes faulty. Causes of a bad switch rocker can include wear and tear from frequent use, exposure to high temperatures, electrical malfunctions, or physical damage from impacts or mishandling. A defective switch rocker can result in unresponsive controls, making it challenging to operate the range effectively.

Symptoms of a bad Range Switch Rocker include:

• The switch not responding when pressed
• Inconsistent or flickering performance of the heating elements
• Physical damage or looseness in the switch
• Intermittent operation or complete failure to activate the desired function

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw is an OEM part for Frigidaire ovens. This screw secures the oven door handle to the door, ensuring it remains firmly attached and stable during use.

Causes of a bad screw can include wear and tear over time, corrosion from exposure to heat and moisture, or damage from over-tightening or stripping.  

Symptoms of a bad screw include:

• The oven door handle feeling loose or wobbly
• The handle detaching from the door
• Difficulty in securing the handle properly
• Visible damage or rust on the screw

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Vent Trim is an OEM part for Frigidaire ranges. This part frames and supports the oven's ventilation system, ensuring proper heat dispersal and maintaining the aesthetic integration of the range within the kitchen setup.  

Common causes for vent trim issues include physical impacts during cleaning or use, thermal deformation from continuous exposure to high temperatures, and general wear and tear over time.  

Symptoms of failing Vent Trim include:

• Loose or ill-fitting trim that may not stay in place
• Visible damage such as cracks or warping due to heat exposure
• Increased heat retention or abnormal heat outside the oven
• Aesthetic discrepancies that impact the overall look of the kitchen

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Seal is an OEM part for Frigidaire ranges. This seal creates a tight barrier to prevent heat from escaping during cooking. Maintaining a proper seal ensures that the oven operates efficiently, maintains the correct temperature, and provides even cooking results.

Causes of a bad range door seal can include wear and tear from regular use, exposure to high temperatures, or damage from cleaning tools.  

Symptoms of a bad range door seal include:

• Heat escaping from around the oven door
• Uneven cooking or longer cooking times
• Visible cracks, tears, or deformation on the seal
• The oven door not closing tightly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Burner Orifice is an OEM part for Frigidaire ranges. This part regulates the flow of gas to the burners, ensuring proper combustion and heat output.  

Causes of a bad burner orifice can include clogging from debris or food particles, corrosion or damage to the orifice opening, or improper installation or misalignment.

Symptoms of a bad burner orifice include:

• Uneven or flickering flames on the burners
• Yellow or orange-colored flames instead of a steady blue flame
• Burners producing excessive noise or popping sounds
• Difficulty in igniting the burners or keeping them lit
• Inconsistent heat output or hot and cold spots on the cooking surface

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This surface burner ignitor/orifice assembly directs gas through a calibrated orifice and provides the spark to ignite it. Replacing a worn or damaged assembly restores consistent lighting and an even flame on the affected rangetop burner.

• Routes gas from the valve through the orifice to the burner head
• Positions the ignitor for reliable sparking and quick ignition
• Helps maintain correct flame size and pattern on that burner
• Common symptoms: burner won't light, clicks without flame, delayed ignition, weak or uneven flame

• Disconnect power and shut off the gas supply before servicing
• Remove grates, caps, and burner heads; lift the cooktop to access the assemblies
• Note wire routing and original orifice location; transfer any reusable hardware from the old part
• After installation, restore gas and check connections for leaks, then test spark and flame

This replacement fan blade mounts to the appliance's fan motor to move air as designed. Installing a new blade restores proper airflow and helps reduce vibration or noise caused by bent, cracked, or worn fins. What it does

• Attaches to the fan motor shaft to move air through the cavity or across internal components
• Supports even air circulation or cooling performance, depending on model
• Helps resolve issues such as loud scraping/whirring, vibration/wobble, weak airflow, or visible blade damage

• One fan blade

• Disconnect power at the breaker and allow the appliance to cool completely before servicing
• Access the fan assembly from the rear panel or inside the oven behind the fan cover (varies by model); wear gloves—edges can be sharp
• Note blade orientation/rotation and securely reinstall using the original fastener(s)
• Hand-spin the blade to ensure clearance and free movement before reassembly and testing

This replacement surface burner head restores a steady, even flame on your gas cooktop. It mixes gas and air and distributes the flame evenly to help ensure reliable ignition and consistent cooking performance.

• Mounts over the orifice and channels gas/air through flame ports for even heating
• Helps resolve weak, uneven, or yellow flames and delayed ignition
• Can address clicking without lighting or burners that won't stay lit
• Durable cast construction designed for repeated heating cycles

• Disconnect power and shut off gas; allow the appliance to cool completely
• Remove grates and access the burner per your model; transfer any mounting hardware from the old part if needed
• Seat the new burner head squarely over the orifice and ensure proper alignment
• Restore gas and power; test for proper ignition and flame. If any gas connections were disturbed, check for leaks with soapy water.

The Surface Burner Cap is an essential OEM component for Frigidaire gas cooktop ranges. It regulates flame spread and directs heat precisely to pots and pans placed above each burner coil.

Causes of burner cap failure include warping or discoloration from continuous exposure to open flames and high cooking temperatures over time. Accidental impacts could also crack or fray burner cap edges.

Symptoms of a faulty burner cap include:

• Irregular or uneven flame patterns beneath cooking vessels   
• Visible yellow or blue flames indicating poor combustion  
• Signs of cracked porcelain or scorched burner bases
• Reduced burner efficiency and poor heat distribution

This authentic OEM replacement is compatible with Electrolux, Gibson, Kelvinator and select Kenmore models.