Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Leaking water from your refrigerator or no water/ice from dispenser? This water inlet valve controls flow to ice maker and dispenser. DIY repair in 30 min.
I replaced the solenoid valve and trimmed a small amount of the tubing that serves the ice maker and water dispenser. The only problem was there is almost NO slack in that tubing. If you trim more than a half inch off, you won't have enough tubing to connect it on both ends. Read more
Fix a stuck or non-working ice/water dispenser with this micro switch. Common cause of dispensers running continuously or not activating. Easy DIY repair.
After my layman's diagnosis (hope) of a bad micro switch to the ice dispenser (would not activate and dispense ice through the chute) I purchased the both the ice and water dispenser micro switches (kill two birds with one stone). Albeit the video attached to these parts may be helpful to some it was not applicable to my refrigerator, as you could not access it from the front by removing the exterior dispenser plate. Don't try this on the LG, LFX25991ST series, refrigerator or you may break it... Read more
Connects French doors on refrigerators. Replace if cracked, broken, or spring-damaged. Installs between doors to maintain proper seal alignment.
Removed 2 screws from mullion strip heater and slid it up off the tabs at top and bottom. Unhooked the plug and removed it. Verified proper mullion heater and then plugged wiring connection back together, positioned slide clips back in line and slid mullion down onto the clips. Tucked the wiring back into opening positioned cover back in place and reiinstalled the 2 screws. It took about 10 minutes for the entire job. the 2nd problem was a noisy evaporator motor and is a more intense repair... Read more
Controls ice dispenser door opening and closing. Replace if door won't open, stays open, or motor makes no sound when dispensing. Mounts behind dispenser trim.
Unplug refrigerator. Use non marring (plastic trim stick) tool to gently pry loose the plastic assembly containing the PCB display beginning at the lower edge and proceeding around the outer edge. Disconnect all connectors and note the routing of each wire harness and connector (take pictures on cellphone as necessary). Remove two screws holding inner PCB mount bracket in place to expose actuator, flapper door and linkage. Replace actuator (three mounting screws) and ensure that actuator... Read more
Dual roller wheel assembly that mounts to the rear wall of the freezer drawer. Replace when wheels are missing, broken, or cracked for smooth sliding.
With your part and 5 minutes. Quick and easy. Read more
Fix no water or ice issues with this water inlet valve. Common when ice maker won't fill or dispenser trickles. Easy 10-minute DIY with video guide.
Replaced icemaker Read more
Keeps refrigerator air fresh by filtering odors and contaminants. Replace every 6 months or when indicator alerts. Confirm fit with your model number.
Just wanted to say how incredibly nice and helpful the gentleman was that helped me on the phone when I called to place the order. Very nice..... Read more
Stores and supplies water to your refrigerator's dispenser and ice maker. Replace if cracked, leaking, or damaged from mineral buildup or freezing.
Replaced tank assembly. Actually I think the supply hose was originally not fully seated in the tank and I think I could have re-seated it deeper through the gray bushing. When I set the line into the new tank, still leaking. Pulled out supply line and reset using a little more force and line went into the tank. Took the bushing clip off the other tank and used it for the supply line bushing. So far, no leaks. The thing to remember is to push the edges of each hose bushing inward to pull... Read more
Hinge assembly for refrigerator doors. Installs at door pivot point to support door weight and enable smooth opening/closing. Replace if cracked or worn.
There is one hinge on top and one at the bottom, but it was none of these it ended up being this hinge that I ordered. Door was having a little hesitation at closing, the door would not pull your hand to close or it would not closed by itself. replaced this part and the refrigerator was fixed. Read more
Seals the ice bank door to prevent warm air from melting ice and causing clumping. Replace if ice melts, refreezes into clumps, or frost forms around the bin.
We have an LG fridge that is 10 years old that was starting to have sweating problems around all the gaskets. So it was either a new fridge or try replacing the gaskets. I purchased a new ice maker door gasket using the parts catalog on the website. Very easy to order and they offer a short video to show the technique to switch out the old and new gaskets. Also did the same thing with the door gaskets and freezer drawer gasket. Website was very easy to work with and find the correct parts and... Read more
Replacement mounting stud for refrigerator door handles. Installs inside the door to secure handle assembly. Needed when stud is damaged or missing.
Ordered new freezer arm Read more
Fix warm refrigerator or freezer temps with this evaporator fan motor assembly. Circulates cold air throughout compartments. Located behind freezer wall.
Roller component for the ice dispenser door handle on bottom-mount refrigerators. Replaces broken, worn, or missing rollers. Ensures smooth handle operation.
Threaded bases for two roller screws were ~ 80% broken off. Used a short (just barely extends past the end of the roller) sheet metal screw to secure the roller in the upper sliding section of the handle (handle in place first). The head was thick enough to fill the gap between the roller and the cover. Filling that gap accurately is important. Need to keep the roller pushed into the recessed area in the door. (Do a test fit with the parts before trying to install them on the door). Turn the... Read more
Fix a warm fridge or squealing fan noise with a new condenser fan blade. Circulates air over condenser coils. DIY repair takes about 30 minutes.
I bought a new cooling motor and blade and installed it, everything seems to be working fine now, did not take that long to fix, maybe about 30 minutes, the longest part was trying to get the old fan off the old motor, finally had to cut it off with bolt cutters, I have a 12 year old LG Refrigerator 26930 double door, if you are handy its not that hard. I had to remove a couple parts in front of the motor to get to it, but very easy. Better than buying a new refrigerator...:). I replaced the... Read more
Supports and stabilizes your refrigerator door for proper alignment. Replace if bracket is cracked, broken, or causing door misalignment issues.
Replaced part. Read more
Ice maker stopped dropping ice or has a cracked tray causing leaks? This complete ice maker assembly restores ice production in your refrigerator.
Replaced the Ice Maker Assembly Kit. Read more