Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Leaking water from your refrigerator or no water/ice from dispenser? This water inlet valve controls flow to ice maker and dispenser. DIY repair in 30 min.
I replaced the solenoid valve and trimmed a small amount of the tubing that serves the ice maker and water dispenser. The only problem was there is almost NO slack in that tubing. If you trim more than a half inch off, you won't have enough tubing to connect it on both ends. Read more
Ice maker stopped working or producing misshapen ice? This complete assembly replaces a faulty ice maker. Moderate DIY repair, about 1 hour with basic tools.
This was easier then I made it. Originally took the actual ice maker out without removing the whole system from the door. There are 3 silver screws that do that hold the whole mechanism in place, as opposed to the 5 white screws that hold the ice maker in place. With the entire assembly out it was a matter of routing the ground wire, retaping the wires, and then the whole assembly went back into the door without a problem. Need a phillips and a flat screwdriver, I also found a needle nose... Read more
Fix a stuck or non-working ice/water dispenser with this micro switch. Common cause of dispensers running continuously or not activating. Easy DIY repair.
After my layman's diagnosis (hope) of a bad micro switch to the ice dispenser (would not activate and dispense ice through the chute) I purchased the both the ice and water dispenser micro switches (kill two birds with one stone). Albeit the video attached to these parts may be helpful to some it was not applicable to my refrigerator, as you could not access it from the front by removing the exterior dispenser plate. Don't try this on the LG, LFX25991ST series, refrigerator or you may break it... Read more
Door basket assembly installs in refrigerator door to organize condiments, jars, and bottles. Replace if cracked, broken, or missing for proper storage.
CHANGED THEM OUT MY SELF Read more
Removes impurities and contaminants from water and ice. Replace every 6 months or 200 gallons for clean, fresh-tasting water. Verify fit by model.
I ordered one from you and replaced it. Read more
Replacement door basket assembly for refrigerator doors. Holds condiments, bottles, and small items. Order when your bin is cracked, broken, or damaged.
Refrigerator stopped cooling after power outage? The compressor overload protector prevents overheating damage. Easy DIY fix when compressor won't run.
Removed and replaced the compressor start relay. Read more
Replacement door bin for refrigerator storage. Installs on the door to organize bottles, jars, and condiments. Replace if cracked, broken, or damaged.
Refrigerator not cooling or freezer warm? The compressor assembly circulates refrigerant to maintain temperature. Professional installation recommended.
Ordered a new compressor and repaired by 3rd party. Read more
Fridge freezing food or not cooling? This temperature sensor monitors internal temps and signals the control board. Fixes ER FF errors. Easy install.
I replaced the evaporator sensor. Your company sent me the exact sensor I needed at a great price. No other company was able to help. No call was needed. Your website was great. Read more
Connects French doors on refrigerators. Replace if cracked, broken, or spring-damaged. Installs between doors to maintain proper seal alignment.
Removed 2 screws from mullion strip heater and slid it up off the tabs at top and bottom. Unhooked the plug and removed it. Verified proper mullion heater and then plugged wiring connection back together, positioned slide clips back in line and slid mullion down onto the clips. Tucked the wiring back into opening positioned cover back in place and reiinstalled the 2 screws. It took about 10 minutes for the entire job. the 2nd problem was a noisy evaporator motor and is a more intense repair... Read more
Controls ice dispenser door opening and closing. Replace if door won't open, stays open, or motor makes no sound when dispensing. Mounts behind dispenser trim.
Unplug refrigerator. Use non marring (plastic trim stick) tool to gently pry loose the plastic assembly containing the PCB display beginning at the lower edge and proceeding around the outer edge. Disconnect all connectors and note the routing of each wire harness and connector (take pictures on cellphone as necessary). Remove two screws holding inner PCB mount bracket in place to expose actuator, flapper door and linkage. Replace actuator (three mounting screws) and ensure that actuator... Read more
Refrigerator mullion door won't close or seal properly? This spring operates the center divider flapper door. DIY-friendly installation in 5 minutes.
Went looking for the spring for my refrigerator door mullion and it is not available for my model. Was told that I had to purchase the entire mullion for $130. Saw some videos on the web about replacing the spring making sure I got the one with the right number of coils. My broken one had 6 coils, I looked at the picture of the spring and counted six coils so I bought it and it worked fine. Read more
Fix no water or ice issues with this water inlet valve. Common when ice maker won't fill or dispenser trickles. Easy 10-minute DIY with video guide.
Replaced icemaker Read more
Fix a dispenser that won't stop running or fails to dispense ice or water. This switch activates your dispenser when pressed. DIY-friendly repair.
Keeps refrigerator air fresh by filtering odors and contaminants. Replace every 6 months or when indicator alerts. Confirm fit with your model number.
Just wanted to say how incredibly nice and helpful the gentleman was that helped me on the phone when I called to place the order. Very nice..... Read more