Maytag Cwe 4800 Parts

The Air Tower is an OEM component for GE side-by-side refrigerator models designed to distribute cold airflow across shelves and crisper bins. Strategically located in the fresh food compartment, it facilitates even temperature regulation within. Efficient airflow relies on an intact tower design.

Symptoms of a defective air tower include:  

• Warm spots or frost buildup noticed on certain shelves and walls   
• Fluctuating temperatures displayed on control panels
• Condensation or moisture issues in unaffected areas

Causes stem from common blockages within vent channels from food debris over time, wear of fan blade bearings reducing distribution power, or cracks in injection-molded tower walls.

Replacing with this genuine GE part restores optimum temperature balance throughout the refrigerator. Compatible for replacement fits Hotpoint, RCA, or Kenmore units seeking uniform chilling without dead zones developing. Regular cleaning helps but replacement maintains long-term efficiency.
 

This clip secures the evaporator thermistor to the evaporator tubing so the control can read coil temperature accurately. Replacing a damaged or missing clip helps restore correct cooling and defrost performance by keeping the sensor firmly in place. What it does:

• Holds the evaporator thermistor tightly against the evaporator coil/tubing for accurate temperature sensing
• Supports proper cooling regulation and defrost cycle timing
• A loose or misplaced sensor may show temperature swings, long run times, or frost buildup on the evaporator
• Restores correct sensor placement after repairs or when the original clip is lost or broken

• 1 evaporator thermistor clip

• Unplug the refrigerator; interior metal edges and fins are sharp—wear cut-resistant gloves
• Remove the evaporator cover to access the sensor; note the original sensor location and orientation
• Transfer the thermistor into the new clip and attach it at the same spot so the sensor makes firm contact; do not pinch wires
• Reinstall panels, keep wiring clear of the fan, and restore power

This cam closure is the small pivot piece that helps the refrigerator fresh-food door close and stay aligned. Replacing a worn or broken cam restores smooth door movement and helps the door seal evenly to maintain cooling. What it does:

• Guides the fresh-food door cam so the door pivots and latches correctly.
• Helps correct sticking doors, doors that hang or bind, and uneven gaps that can let cold air escape.
• Replaces a worn, cracked, or broken closure that can cause misalignment or noisy door operation.

• Disconnect power or unplug the refrigerator before beginning any work.
• Remove the door or access trim per the manufacturer's instructions to reach the cam area; keep track of hinge pins and fasteners.
• Pry or pop out the old cam and press the replacement into the cam slot until it snaps into place; check door alignment and operation after installation.

The Flat Chrome Badge is an OEM part for GE refrigerators. It is responsible for displaying the GE logo and model information on the front of the refrigerator. As an identifiable brand marker, the badge contributes to the overall appearance and style of the appliance.

Causes of a bad badge can include damage from impacts or bending, discoloration or tarnishing over time, or simple wear and tear that renders the badge appearance faded or illegible.

Symptoms of a bad badge include:

• A missing, loose, crooked or illegible badge
• Signs of denting, scratching or corrosion
• An outdated or inconsistent badge that doesn't match the model

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

The Manifold & Housing are OEM components specifically designed for GE refrigerators. This part includes both the manifold which distributes water and the outer housing that protects it. 

The manifold & housing work together to deliver filtered water to the refrigerator's dispenser and ice maker. It is responsible for efficiently directing water flow and ensuring reliable operation of components that require water. 

Symptoms of a bad manifold & housing include:

• Low water pressure at the dispenser 
• Streaking or staining around water line connections
• Ice maker or dispenser malfunctions due to lack of water
• Dripping or leaks from manifold or housing areas

This OEM GE part is specifically designed to fit your model fridge. It is also compatible with Hotpoint, RCA, and some Kenmore models for a factory fit and like-new performance.

The 2-pack Hinge End Cap Assembly is an OEM replacement part for GE refrigerators. This assembly is responsible for providing support and stability to the refrigerator door hinges, ensuring smooth opening and closing.

A bad hinge end cap assembly can occur due to regular wear and tear or accidental damage. If you notice symptoms such as a loose or sagging door, difficulty in opening or closing the door, or the door not staying securely in place, it may indicate a need to replace this assembly.

Symptoms of a bad hinge end cap assembly include:

• Loose or sagging refrigerator door
• Difficulty in opening or closing the door
• Door not staying securely closed

Restore your refrigerator's door by replacing the faulty hinge end cap assembly with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

Replacement indicator light for control panels that restores visible status and cycle feedback. Ideal when the control-panel light is dim, cracked, or not illuminating—helps active functions and cycle progress at a glance. What it does:

• Illuminates to indicate active functions and cycle/status information on the control panel.
• Replaces a cracked, burnt-out, dim, or non-functioning indicator light.
• Common symptoms it can fix: a dark, flickering, or intermittently working panel indicator.

• Disconnect power (unplug or shut off the circuit breaker) before servicing the appliance.
• Access may require removing the control panel or lens; follow the owner's manual or service guide for panel removal.
• Handle the light and lens carefully to avoid damage; avoid touching bulb surfaces with bare hands.

This mounting screw secures appliance components to the chassis for a tight, rattle-free fit. Replacing a missing, stripped, or corroded fastener helps keep panels, brackets, or burner assemblies properly aligned and secure.

• Fastens designated parts to the appliance frame or mounting points
• Helps maintain proper alignment of panels, trim, brackets, or burner assemblies
• Restores hold when the original screw is worn, rusted, or lost
• Symptoms include loose or wobbly components, rattling/vibration, or visible gaps

• Disconnect power; allow all surfaces to cool. For gas units, also shut off the gas supply.
• Use the correct driver/bit; avoid cross-threading.
• If mating threads or clip/nut are damaged, repair or replace them before installing.
• Tighten until secure; do not overtighten to prevent stripping.

A shoulder screw that secures appliance components and provides a precise pivot or spacer point. Replaces a missing or worn screw to restore alignment, reduce rattling, and keep panels and assemblies securely in place. What it does:

• Provides a fixed-diameter shoulder for pivots, spacers, or mounting points in assemblies.
• Holds panels and moving components at the correct distance to prevent binding or friction.
• A missing or worn shoulder screw can cause misalignment, rattling, or loose parts during operation.
• Used where a smooth-bearing surface and controlled clearance are required between parts.

• Disconnect power to the appliance (unplug or shut off breaker) before servicing.
• Handle small fasteners carefully to avoid dropping into assemblies; magnetic pickup tools can help.
• Start threads by hand to avoid cross-threading; tighten snugly but avoid overtightening.

This quick-connect clip secures 5/16-inch water tubing in push-to-connect fittings to prevent accidental release and leaks at the joint. Restore a reliable hold on dispenser and icemaker lines when the original clip is missing or damaged. What it does:

• Locks the release ring (collet) on a 5/16-inch quick-connect fitting to retain tubing
• Helps prevent water drips or leaks at the connector
• Keeps tubing from slipping out, supporting steady water flow to dispenser/ice maker
• Common symptoms: leak at fitting, loose/disconnected tubing, no/low water or ice

• 1 quick-connect clip (5/16)

• Unplug the appliance and shut off the water supply; dispense water to relieve line pressure
• Ensure the tubing end is cut square; push it fully into the fitting until seated
• Insert the clip beneath the fitting's collet to lock; tug gently to verify retention
• Restore water and power, then check all connections for leaks

• Designed for 5/16-inch OD water tubing quick-connect fittings

Replacement grille thermistor. This temperature sensor monitors air at the grille location and relays the signal to the control so cooling and defrost responses stay consistent and food stays within target temperatures.

• Senses ambient air temperature at the grille and varies resistance with temperature
• Sends data to the control to help regulate compressor/fan run time and defrost intervals
• Aids in maintaining stable refrigerator and freezer temperatures
• A failing sensor may lead to temperature swings, extended run time, or irregular defrosting

• Disconnect power before servicing
• Remove the grille/kickplate to access the sensor and its connector
• Disconnect the old sensor, install the new one, and route wiring as originally; ensure the sensor is fully seated and wires aren't pinched
• Restore power and allow up to 24 hours for temperatures to stabilize

Conduction heater for the freezer compartment that melts frost from the evaporator during defrost cycles, helping prevent ice buildup and maintain consistent cooling. Replaces a failed freezer conduction heater to restore defrost function. What it does:

• Heats the evaporator area during defrost cycles to melt accumulated frost and ice.
• Helps prevent excessive ice buildup that can reduce cooling efficiency.
• Common symptoms of a failing heater: visible ice/frost on the evaporator or freezer interior and inconsistent freezer temperatures.
• Designed as a replacement conduction heater for compatible GE freezer evaporator assemblies.

• Disconnect power to the appliance before servicing to avoid electric shock.
• Access typically requires removing the freezer evaporator cover or rear panel.
• Handle the element carefully to avoid damage.

A double water inlet valve assembly that controls water flow to the refrigerator's ice maker and dispenser, restoring proper filling and preventing intermittent supply issues when the original valve fails. Fits systems using a dual-solenoid inlet valve. What it does:

• Regulates water delivery to the ice maker and to the dispenser by opening and closing the two solenoid ports.
• Replaces a worn or stuck valve that can cause the ice maker not to fill or the dispenser to stop dispensing.
• Stops unwanted continuous flow or slow filling caused by a leaking or clogged inlet valve.
• Helps eliminate water pooling or inconsistent ice production linked to valve failure.

• Disconnect power and shut off the water supply before beginning service to avoid shock or flooding.
• Inspect inlet hoses and fittings for damage; replace any worn lines before installing the new valve.
• Tighten connections and restore water, then check carefully for leaks and proper ice maker and dispenser operation.

This hex-head sheet metal screw secures appliance panels, brackets, and trim for a tight, rattle-free fit. Replace missing or stripped fasteners to keep covers and components firmly in place and restore proper alignment.

• Fastens sheet-metal parts, brackets, and trim using a hex drive
• Replaces worn, rusted, missing, or stripped screws
• Helps reduce vibration and rattling from loose panels
• Common signs you need this fastener: head or threads stripped, screw won't tighten, panel or handle coming loose

• Unplug the appliance before service; turn off water supply if working near water lines
• Use the correct nut driver or socket to avoid rounding the head
• Replace one fastener at a time to maintain alignment; do not overtighten
• Match screw type/length to the original location as specified by the manufacturer

This broil element mounts at the top of the oven cavity and delivers the intense radiant heat needed for broiling. Replace a failed element to restore reliable top heat and consistent broil results in your range or wall oven.

• Provides strong, direct radiant heat from the top of the oven during the Broil cycle
• Common signs of failure: no broil heat, uneven broiling, visible breaks/blistering, or tripping the breaker when Broil is selected
• Restores proper broiling when the original element is open or shorted
• Also known as the upper/top oven element; verify fit with your model number

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the oven to cool completely and wear cut-resistant gloves
• Remove mounting screws, gently pull the element forward, and support the wires so they don't slip back through the liner
• Transfer wires one at a time to the new element, secure the element, check connections, restore power, and test

Specs: 8-18 AB IHW 5/8 S