Maytag Mdb4949sdh1 Parts

This factory-specified screw secures panels, brackets, and internal components in your appliance. Replacing worn or missing hardware restores a tight fit to help reduce vibration, noise, and premature wear.

• Fastens sheet metal, brackets, or plastic parts as designed by the manufacturer
• Helps maintain alignment and reduce vibration/rattling
• Direct replacement for stripped, corroded, or missing screws
• Common signs: loose panels or trim, shifting components, screw won't tighten

• Disconnect power; shut off water or gas supply if applicable
• Use the correct driver to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening
• Replace one-for-one in the original location per service information

This replacement wire restores a reliable electrical path between appliance components. Use it to replace a damaged or heat-stressed lead so power or signal can flow correctly for consistent, safe operation.

• Carries electrical power or signals between components to restore continuity
• Helps resolve issues caused by broken conductors, loose/burned terminals, or brittle insulation
• Can address intermittent operation or components not energizing due to an open circuit
• Ideal when the original lead shows scorching, melting, or corrosion

• Disconnect power (and shut off gas/water if applicable) before servicing
• Document wire routing and connections before removal to ensure correct reassembly
• Transfer any reusable sleeves, clips, or ties from the old lead if present
• Seat connections fully and route the wire away from sharp edges and high-heat areas

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This compression tube nut secures water inlet tubing to a threaded fitting to create a reliable, leak-resistant seal. Replace a cracked or stripped nut to stop drips at the connection and keep your appliance's water system working properly.

• Compresses the tubing against the fitting to seal the water line at the inlet valve, filter head, or other water-system connections
• Helps correct leaks at the water line connection point
• Replaces nuts that are cracked, cross-threaded, or deformed
• Common symptoms: water dripping at the connection, difficulty tightening the line, or a poor seal after reassembly

• Shut off the water supply and disconnect power before servicing.
• Slide the nut onto the tubing first, seat the tube fully on the fitting, then hand-tighten and snug with a wrench; do not overtighten.
• Inspect and reuse the existing sleeve/ferrule and tube insert if in good condition; replace if worn.
• Restore water and check for leaks at the connection.

The door balance mount is the side-frame bracket that supports the dishwasher's door counterbalance system. When worn or broken, it can let the door drop, slam, bind, or feel heavy. Replacing it restores smooth, controlled door movement. What it does

• Anchors the door springs and balance link/cable to counterbalance the door's weight
• Helps the door open and close smoothly without dropping or slamming
• Guides the balance link for consistent, quiet movement
• Common symptoms: door feels heavy or uneven, falls open, won't stay put, or makes grinding/squeaking noises; visible damage to the bracket or rollers

• One door balance mount (bracket)

• Disconnect power and shut off water before servicing
• Pull the dishwasher out slightly to access the side where the mount is installed
• Carefully relieve spring tension; note link/cable routing before removal
• Transfer the spring/link to the new mount, secure the bracket, and check door balance on both sides

This inner door seal forms a moisture barrier between the dishwasher tub and the door assembly, helping keep wash water and steam contained. Replacing a worn seal can stop drips at the door and protect internal components.

• Seals the joint along the inner door to contain wash water and steam
• Helps prevent door-area leaks or drips during cycles
• Blocks moisture from entering the door cavity where electrical parts reside
• Common signs: water at the bottom/sides of the door, damp control area, visible wear/flattening or tears on the seal

• Disconnect power and turn off water supply before servicing
• Open the door and remove perimeter screws to separate inner/outer door panels
• Remove the old seal; clean the mounting surface and note seal orientation
• Press the new seal firmly into place, reassemble, and run a leak check

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This dishwasher sump and seal forms the watertight basin at the bottom of the tub and seats the wash and drain pumps. Replace a cracked sump or worn seal to stop leaks and restore reliable wash performance. What it does:

• Collects and channels wash water to the circulation and drain pumps
• Maintains a watertight seal between the tub and the sump opening
• Helps maintain proper wash pressure and flow
• Common failure signs: water leaking from the base, visible cracks or warping, recurring moisture beneath the unit, poor cleaning results

• One sump assembly with seal

• Disconnect power and shut off the water supply before servicing; use towels to catch residual water
• Remove the toe panel and slide the dishwasher out for access to the sump area
• Detach hoses/wiring as needed; release locking tabs and lift out the old sump
• Seat the new seal evenly, transfer any reusable hardware/components from the original sump, and test for leaks after reassembly

This replacement capacitor stores and releases energy to give an AC motor the phase shift it needs to start and run smoothly. Installing a fresh capacitor can help when a motor hums, struggles to start, or cycles off. What it does

• Provides the phase shift/starting torque an AC motor needs and stabilizes operation
• Helps reduce repeated start attempts and nuisance thermal trips
• Common symptoms of a weak capacitor: motor hums, won't start, or stops shortly after starting
• Physical signs of failure can include a swollen, leaking, or cracked casing

• 1 capacitor

• Disconnect power to the appliance before servicing
• Safely discharge the capacitor with an appropriate resistor/discharge tool before handling
• Mark/photograph wire locations and transfer connections one-for-one to the new part
• Reinstall in the original bracket or mounting location; keep wiring secure and clear of moving parts

This rear support wheel replaces a worn roller that helps a sliding drawer or rack glide smoothly and stay aligned. Restores easy, even movement and reduces dragging, scraping, or tilting during everyday use.

• Supports the rear of a sliding assembly on its track
• Provides smooth rolling action and helps maintain alignment
• Helps prevent binding, popping off the track, or uneven travel
• Replace if the wheel is cracked, flattened, missing, or if movement is noisy or difficult

• Disconnect power before servicing; allow the appliance to cool
• Remove the sliding assembly to access the wheel area
• Transfer or reinstall any axle/retainer from the original wheel as needed
• Verify smooth travel and proper alignment after replacement

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

12 Ft in length

Includes two screws, two clamps, and undercounter mounting brackets.

This insulation pad installs in the factory location to isolate and cushion components or panels. It helps reduce vibration and limit unwanted heat transfer, supporting quieter operation and proper performance where the original pad was installed.

• Provides a thermal and acoustic barrier between parts or panels
• Helps minimize vibration and rattling noises
• Restores proper spacing/cushioning when the original pad is missing or deteriorated
• Replace if the pad is brittle, compressed, contaminated, or falling off
• Common signs include increased noise or rattles and localized hot spots or condensation

• Disconnect power (and gas/water, if applicable) before servicing
• Allow hot or cold surfaces to return to a safe temperature
• Note the original pad's location/orientation; remove old pad and clean the surface
• Install the new pad in the same spot without over-compressing; secure per the original method and verify clearances

This drain adapter assembly links the dishwasher's drain outlet to the drain hose leading to a sink drain or garbage disposer, creating a secure, watertight discharge path. Replacing a damaged adapter helps stop leaks and supports proper draining.

• Adapts and seals the outlet from the sump/pump to the drain hose or disposer
• Helps maintain proper discharge flow during the drain cycle
• Common symptoms include water under the unit and standing water left in the tub

• Disconnect power at the breaker and shut off water; bail out any standing water
• Access the drain outlet and place a towel or pan to catch residual water
• Move the hose clamp, remove the old adapter, and seat the new adapter squarely
• Reattach the hose, secure the clamp, and run a brief test cycle to check for leaks

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.