Maytag Mdb9600aws Parts

Attaches to the inner tub for the upper rack

Long tub insulation that fits the appliance's inner tub, reducing operating noise and helping stabilize temperature around the tub for quieter, more consistent performance. Replaces worn or damaged insulation to address rattles and drafts. What it does:

• Dampens noise and vibration when insulation is torn, compressed or missing.
• Helps limit heat loss and reduce cold spots that can cause condensation or longer warm-up times.
• Reduces rattling or knocking caused by loose or degraded insulation.
• Intended for specific Whirlpool tubs—verify model fit before ordering.

• Disconnect power (and water supply for washers) before starting any repair.
• Remove outer panels or drum components per the service manual; insulation may be held with clips, adhesive, or fasteners.
• Wear gloves and a dust mask—insulation fibers can irritate skin and lungs.

This dishwasher door strike mounts to the tub opening and provides the catch point for the door latch. Replacing a worn or bent strike restores positive latching so the control can sense a closed door and run cycles reliably.

• Provides the catch the door latch locks onto
• Engages the door switch so the dishwasher can start
• Helps keep the door securely closed during operation
• Common symptoms: door won't latch or pops open; unit won't start unless pressure is applied to the door; strike is visibly bent, worn, or missing

• Disconnect power at the breaker; turn off water if you need to move the appliance
• Open the door to access the strike at the tub opening; remove mounting screws, replace the strike, and tighten securely
• Save and reuse the original mounting screws
• After installation, check latch engagement and adjust appliance leveling or alignment if needed

This little door seal goes on the corner of the dishwasher door. There are two of these seals - one in each corner. It is recommended to order and replace both. If you need pushnuts, order 99002756.

This dishwasher drain hose channels wastewater from the pump to your home drain or air gap. Replacing a cracked, kinked, or clogged hose restores proper draining performance and helps prevent leaks or water backing into the tub. What it does:

• Routes wastewater from the dishwasher to the household drain or air gap
• A damaged, kinked, or blocked hose can cause slow/no drain, standing water, or leaks
• Visible splits, soft spots, or persistent odors/backflow are common signs the hose should be replaced
• Restores reliable draining and helps protect surrounding cabinets and flooring from water damage

• 1 drain hose

• Disconnect power and shut off water before servicing
• Pull the dishwasher forward and place a towel or pan to catch residual water
• Match the original routing and maintain a proper high loop or air gap per local code to prevent backflow
• Secure connections with clamps, ensure the hose isn't kinked, and run a test cycle to check for leaks

This adjustable clip is used to hold the tines in place on a dishwasher rack. Color: blue. Measures about 3-3/4 inches wide by a 1/2 inch high.

Used on the end of the rails to prevent the upper rack from falling out.

This lower dishwasher rack fold away row tine can be used for both the left and right hand side. Color: light gray. Measures about 3-1/2 inches high by 10 inches deep.

This top wash arm retainer secures the dishwasher's upper spray arm so it spins freely and stays aligned, helping maintain proper water distribution for upper-rack cleaning. Replace a cracked or worn retainer to reduce wobble and misalignment. What it does:

• Holds the upper/ top spray arm in place on the spray assembly so the arm can rotate correctly.
• Prevents the spray arm from slipping or wobbling during the wash cycle.
• Helps restore proper water spray coverage to the upper rack when the original retainer is broken or worn.
• Compatible with standard upper spray arm mounting—no modification required.

• Includes: 1 top wash arm retainer

• Disconnect power to the appliance before beginning any repair.
• You may need to remove the upper rack and/or the spray arm to access the retainer; keep parts organized for reassembly.
• Inspect the spray arm and attachment for damage or debris while replacing the retainer.
• Use hand tools only.

The Tub Wheel supports and guides the washer's tub assembly on its base during wash and spin cycles. Replacing a worn wheel restores smoother, quieter operation and helps reduce vibration and rubbing as the machine operates.

• Provides rolling support so the tub can move and self-balance during cycles
• Reduces friction between the tub and the base/frame
• Helps keep the tub centered to minimize noise and vibration
• Failure symptoms include squeaking or grinding, scraping noises, dragging movement, or visible flat spots/cracks on the wheel

• Disconnect power and water supply before servicing; wear appropriate gloves and eye protection
• Access the base/suspension per the service information and support the tub to remove load from the wheel
• Remove the retainer/axle, install the new wheel, and free rotation and correct orientation
• Reassemble, level the appliance, and run a spin test to check for noise and balance

Screw: 8-16 x 3/8 inch.

Specs: No.8X1/2 HEX WASHER HEAD

Color: light blue. Measures about 6 inches wide by a 1/2 inch high.

Replacement rinse aid dispenser knob restores a simple, reliable way to set and dispense rinse aid in the dishwasher. It gives a clear tactile control for adjusting rinse aid release so dishes dry and rinse with fewer spots. What it does:

• Replaces a cracked, stripped, missing, or hard-to-turn rinse aid control knob
• Allows you to set the dispenser level or open/close the rinse aid dosing mechanism
• Helps resolve problems where the knob won't turn or is detached from the dispenser
• Matches the original dispenser interface for correct fit and operation

• Always disconnect power to the appliance before servicing (unplug or switch off the breaker)
• Access the rinse aid dispenser per the dishwasher service manual or OEM instructions
• Align the knob on the dispenser post and press/snap it into place; avoid forcing or overtightening

Small replacement screw that secures panels and internal components on compatible appliances. Restores proper fastening to reduce rattling and loose parts so controls and panels stay aligned during normal use. What it does:

• Secures panels, brackets, and small components to the appliance frame or assemblies.
• Helps stop rattling, vibration-related noise, and movement from loose parts.
• Replaces a missing, worn, or stripped fastener to restore proper mounting.
• Used wherever the original manufacturer specified this screw in service diagrams.

• Disconnect power and water before working on the appliance to avoid shock or injury.
• Match the replacement screw to the original by fit and thread before installation; do not force mismatched fasteners.
• Start the screw by hand to avoid cross-threading; tighten securely but avoid over-torquing which can strip threads or damage components.
• Refer to the appliance's service manual or parts diagram for exact location and any torque or threadlocker recommendations.

The Cabinet Mount Bracket secures a built-in appliance to the surrounding cabinetry. Replacing a bent or missing bracket restores a tight, rattle-free installation so the unit stays level and aligned during everyday use.

• Anchors the appliance to the cabinet or side walls to prevent shifting or tip-out
• Maintains flush, level alignment with adjacent cabinets and countertop
• Helps reduce vibration and rattling noises during operation
• Replace if the original bracket is bent, cracked, corroded, or missing

• Disconnect power and any utilities before starting work.
• Support the appliance and pull it forward enough to access the mounting area.
• Reuse manufacturer-specified screws or approved replacements; tighten securely without overtightening.
• Secure both sides as originally configured and test operation.