Maytag Washer Centennial Parts

2 position. Extra rinse.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Used for the pressure switch.

A general-purpose 6-20 screw used to secure panels, brackets and small components on Whirlpool appliances. Replaces stripped or missing fasteners to restore a snug fit and reduce rattling or loose parts. What it does:

• Secures appliance panels, trim, brackets and internal components in original mounting locations.
• Stops panel movement, vibration noise and loose connections caused by missing or corroded screws.
• Fits the OEM 6-20 thread designation used on multiple Whirlpool assembly points.
• Sold individually for spot repairs and small part replacements.

• Disconnect power or gas supply to the appliance before starting any repair.
• Use the correct screwdriver or bit to avoid stripping the head; tighten until snug but do not overtighten.
• Replace like-for-like; stop and verify the correct fastener for the mounting point.
• Check the appliance's parts diagram for the exact screw location and orientation.

Right hand side

Designed for use in dryers, the gas valve assembly is a part with solenoids or coils. These are used to close and open the valve that controls how much gas flows through the internal parts of the dryer. The gas valve assembly is made of strong materials but can become damaged or worn out. When this occurs, the dryer may not longer create heat during a cycle. If this happens, test the coils using a multimeter. If the reading is not within 1,000 to 2,000 ohms, the gas valve assembly should be replaced.Before starting, unplug the dryer from the wall and shut off the gas supply. Remove the lint screen from the housing and use a screwdriver to take out the screws in the housing. Disassemble the dryer to gain access to the gas valve and coils. Remove the screws from the mounting bracket to detach this part. Replace with the new component and test before use.The gas valve assembly is designed to be used with dryers by Kenmore, Maytag, and Amana. This genuine OEM part is directly sourced from the manufacturer. It is priced as a single unit.

This angle-sequence timer controls the timed advancement of bake/broil cycles in compatible Whirlpool ranges, restoring proper cycle sequencing and timing for reliable oven operation. What it does

• Rotates an internal cam to open and close cycle contacts, advancing the oven through timed functions.
• Re-establishes timed cycling when the oven fails to advance through bake/broil or self-clean cycles.
• Commonly used when the timer stops clicking, won't turn, or the oven does not start or complete timed operations.
• Works as the mechanical timing control for range/oven cycle sequencing.

• One angle-sequence timer assembly.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Handle the timer carefully to avoid bending terminals or damaging the cam/shaft.
• After installation, restore power and test all timed functions to confirm proper operation.

Replacement housing that supports and protects internal components in compatible Whirlpool appliances. Restores structural integrity to the cabinet, helping reduce vibration and keeping wiring and components enclosed for safe, reliable operation. What it does:

• Provides the outer cabinet support that secures motors, controls and wiring
• Protects internal parts from debris and accidental contact
• Helps reduce rattling, vibration and misalignment symptoms caused by cracked or damaged cabinets
• Restores proper fit for panels and fasteners to eliminate rubbing or interference noises

• Disconnect power (and water if applicable) before starting any repair
• Basic hand tools are typically required; keep screws and clips organized during disassembly
• Some housings may require two people to position during replacement—avoid forcing parts to prevent damage
• Fasteners and any sealing gaskets are in good condition and replaced if worn

Restore smooth operation of your dryer's lint screen cover with this lint screen door spring. It provides the correct tension so the cover opens and closes properly and the lint screen seats securely for reliable lint collection.

• Applies spring tension to the lint screen door/cover hinge
• Helps the lint screen and cover stay properly positioned
• A worn or broken spring may cause the cover to feel loose, pop open, or not stay closed
• May make inserting or removing the lint screen difficult

• Disconnect power; for gas dryers, also shut off gas supply
• Access the lint screen door area per your model's service information
• Note the original spring orientation; transfer the new spring carefully using needle-nose pliers
• Check cover operation and lint screen seating before restoring power

This factory fastener secures appliance components and panels, helping keep assemblies properly aligned and tight. Replace worn, stripped, or missing hardware to eliminate looseness and vibration and maintain safe, reliable operation.

• Fastens brackets, panels, trim, and internal assemblies to the cabinet/frame
• Helps maintain alignment of doors, consoles, or covers
• Restores a tight fit to reduce rattling, vibration, or shifting
• Common symptoms: missing screw, stripped head/threads, loose panel or handle, recurring vibration/noise

• Disconnect power (and shut off gas/water if applicable) before servicing
• Match thread and length to the original fastener for proper fit
• Start threading by hand to avoid cross-threading; use the correct driver
• Do not overtighten into plastic or thin sheet metal

The lid switch lever connects the washer's lid hinge to the lid switch, signaling when the lid is closed so the cycle can run. A damaged lever can prevent the safety interlock from closing, leading to no-start or spin issues. What it does:

• Transfers lid movement at the hinge to the lid switch actuator
• A closed lid so the washer can operate
• Common symptoms of a failed lever: washer won't start; won't spin; cycle pauses because the lid-closed signal isn't detected

• 1 lid switch lever

• Disconnect power before servicing
• Lift or open the top to access the hinge/switch area; locate the lever near the lid switch
• Remove the old lever and install the new one in the same orientation; free movement
• Close the lid by hand and the switch clicks before reassembly and testing

This retainer clip secures a component in place to prevent movement and maintain proper alignment during appliance operation. Replacing a damaged or missing clip helps restore safe, reliable performance.

• Holds the mating part firmly to reduce vibration and noise
• Helps prevent intermittent operation caused by loose fitment
• Common fix when a component feels loose, rattles, or won't stay seated

• Disconnect power and shut off gas/water before servicing
• Note original clip orientation and location before removal
• Use needle-nose pliers to carefully release and install the clip
• Do not over-bend the clip; replace if deformed or fatigued

Size: .20 Fl. Oz. (6 ml)

This rotary on/off switch controls the dryer's Finish Guard (also called Wrinkle Guard/Wrinkle Shield) feature. Replacing it restores proper control of the post-cycle intermittent tumbling that helps reduce wrinkles, preventing the feature from being stuck on or off.

• Provides 2-position on/off selection for the Finish Guard/Wrinkle Guard function
• Failure can cause the feature not to engage or to stay on after the cycle ends
• Knob may feel loose or fail to click when the switch is worn
• Mounts in the control console and interfaces with the external selector knob

• Disconnect power before servicing
• Access through the control console; remove paneling as needed
• Transfer wires one at a time or photograph connections for reference
• Reinstall using the existing knob and mounting hardware

4 position

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening