Mdc 5100 Aww Parts

This is the longer of the two dispenser lid hinge pins. For the shorter lid hinge pin order WPY912679.

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

12 Ft in length

This is the shorter of the two dispenser lid hinge pins. For the longer lid hinge pin order WP6-912678.

Long tub insulation that fits the appliance's inner tub, reducing operating noise and helping stabilize temperature around the tub for quieter, more consistent performance. Replaces worn or damaged insulation to address rattles and drafts. What it does:

• Dampens noise and vibration when insulation is torn, compressed or missing.
• Helps limit heat loss and reduce cold spots that can cause condensation or longer warm-up times.
• Reduces rattling or knocking caused by loose or degraded insulation.
• Intended for specific Whirlpool tubs—verify model fit before ordering.

• Disconnect power (and water supply for washers) before starting any repair.
• Remove outer panels or drum components per the service manual; insulation may be held with clips, adhesive, or fasteners.
• Wear gloves and a dust mask—insulation fibers can irritate skin and lungs.

This power cord strain relief secures the cord where it passes through the appliance cabinet, protecting the jacket and preventing pull on internal connections. Replacing a cracked or missing connector restores a safe, stable cord entry. What it does:

• Secures the power cord at the cabinet entry to relieve strain on internal terminals or junction connections
• Provides a protective bushing to reduce abrasion of the cord jacket against cabinet edges
• Helps maintain proper routing and support for the incoming power cord
• Typical signs it's needed: loose or wobbly cord at entry, broken/missing connector, or visible chafing on the cord jacket

• 1 strain relief connector

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove the access cover, release and remove the old strain relief, and route the cord through the new connector
• Seat the connector fully so it captures the cord's outer jacket—not the individual conductors
• After reassembly, verify the cord is secure and does not move at the entry point

Located between the console and door

Color: Grey (If your original dispenser and cap was blue, the factory has changed it to grey.)

This active vent assembly controls airflow from the dishwasher during and after a cycle, releasing humid air at the right time for better drying. Replacing a faulty vent can reduce lingering moisture and steam escaping from the door.

• Regulates and directs moist air out of the tub during the dry portion of the cycle
• Closes during wash to help contain water and heat inside the dishwasher
• Helps reduce interior condensation and improve overall drying results
• Common failure symptoms: dishes not drying, moisture remaining after the cycle, steam escaping at the top of the door, or unusual noise from the vent area

• Disconnect power at the breaker before servicing; allow the unit to cool
• Access is typically through the inner door panel; retain and reuse mounting hardware as required
• Inspect and correctly seat the vent seal to prevent steam leaks
• After installation, run a test cycle to check for proper vent operation and sealing

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

Replacement fill hose that routes water from the household supply to the appliance's ice maker and water dispenser, restoring proper water delivery and helping prevent leaks or pooling from a damaged line. What it does

• Directs water from the inlet valve to the ice maker and dispenser for ice production and dispensing.
• Maintains steady water flow; prevents kinks and pinched lines that reduce flow.
• Replace if cracked, split, collapsed, or leaking.
• Common symptoms: reduced or no water to the dispenser or ice maker, visible leaks, or pooling under/behind the appliance.

• Turn off the water supply and disconnect power before servicing to avoid flooding and electrical hazard.
• Inspect and replace clamps or fittings as needed; ensure proper seating and a snug, leak-free connection without overtightening.
• Check for kinks in the hose and route it so it won't be pinched by the appliance or cabinetry.
• After installation, turn the water back on and test for leaks at all connections.

This dishwasher overfill control float mounts in the tub floor and rises with the water level to trip the float switch and stop filling. Replacing a warped or stuck float restores proper fill control and helps prevent leaks. What it does:

• Monitors tub water level and actuates the float switch to shut off the inlet valve
• Helps prevent overfilling and water leaking from the door
• Common symptoms of a faulty float include no fill, continuous filling/overfilling, or inconsistent water level

• Float and retainer

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack; lift out the old float
• Access beneath the tub may be required to release/install the retainer
• Ensure the float stem engages the switch lever and moves freely; test-fill and check for leaks

To order indicator lens use WP22001948.

This door switch detects when the dishwasher door is fully closed and latched. Replacing a worn or intermittent switch restores reliable start/stop operation and ensures the safety interlock cuts power whenever the door is opened.

• Senses door-closed status and sends a signal to the control
• Interrupts power to the machine when the door opens
• Helps prevent operation with an unlatched door
• Typical failure symptoms: won't start, stops mid-cycle if the door is bumped, or only runs when pressing on the door

• Disconnect power at the breaker before servicing
• Access the latch/switch area by removing the inner door panel or console; note wire locations
• Transfer wires one at a time and secure the new switch in the bracket
• Verify latch engagement and switch actuation before restoring power

This replacement cabinet screw secures panels, brackets, and ducts in Whirlpool-built appliances so components stay aligned and secure. Replacing missing or stripped hardware helps reduce vibration, rattling, and gaps that can affect performance.

• Fastens panels, brackets, and internal components in the appliance cabinet
• Helps maintain proper alignment and reduce vibration or rattling noises
• Restores a tight fit where original hardware is missing, damaged, or stripped
• Typical symptoms: loose paneling, buzzing/rattling sounds, or parts that won't stay fastened

• Disconnect power; for gas models, also shut off the gas supply
• Replace one fastener at a time to preserve alignment and match to the original hardware
• Use the correct driver; start threads by hand to avoid cross-threading
• Do not overtighten into sheet metal

This impeller assembly replaces a worn or damaged wash-pump impeller to help restore water circulation and spray pressure for better cleaning. Commonly used in compatible Whirlpool wash pumps to address weak wash performance. What it does:

• Spins inside the wash pump to move water through spray arms; damaged fins reduce spray force and cleaning.
• Restores proper flow during wash cycles — symptoms of failure include weak or uneven cleaning.
• Reduces abnormal pump noise and motor strain when the impeller is intact; cracked or missing fins can cause humming or grinding.
• Works with the pump housing and seals to route water; a failed impeller can allow internal leakage or cavitation.

• Always disconnect power (and water, if applicable) before servicing the appliance.
• Inspect pump seals, gaskets, and surrounding components; replace any damaged parts to prevent leaks.