Mle20000ayw Parts

This drain hose carries used water away from your appliance during the drain cycle. Replacing a worn or damaged hose helps stop leaks and restores proper draining performance.

• Routes wastewater from the appliance's drain system to the household drain
• Replaces hoses that are cracked, brittle, clogged, or kinked and leaking
• Can help when cycles end with standing water or slow/failed draining
• Helps reduce odors and backflow when installed and routed correctly

• Disconnect power and water supply; allow the appliance to cool before servicing
• Move the unit for access; keep towels or a pan handy to catch residual water
• Transfer and tighten existing clamps/fittings to the new hose; route without kinks and secure per your model's instructions
• Run a short test cycle and check all connections for leaks

This bracket strike secures the door latch strike to the appliance frame, restoring reliable door closing and sealing. Replacing a damaged or bent bracket helps prevent doors from popping open or failing to latch properly. What it does:

• Secures the door strike so the latch can engage and hold the door closed.
• Restores correct door alignment when a worn or broken bracket causes improper latching.
• Addresses symptoms such as a door that won't latch, pops open, or sits unevenly.
• Provides a direct-fit structural replacement for the original mounting point.

• Disconnect power (and water, if applicable) before beginning any service.
• Access the bracket by removing the door trim or inner panel as required; keep original fasteners.
• Align the strike with the latch, secure with appropriate screws, and test door operation before reassembly.

Screw: 8-16 x 3/8 inch.

Single unit. Includes foot pad.

Specs: No.8X1/2 HEX WASHER HEAD

This replacement screw fastens trim, panels and small components to restore secure attachment and reduce rattling or movement. Use when a screw is missing, stripped, or damaged to keep parts aligned and operating quietly. What it does:

• Secures panels, brackets and trim to appliance assemblies
• Prevents vibration, rattling and misalignment caused by missing or damaged fasteners
• Replaces lost or stripped screws that can allow gaps or loose parts
• Helps maintain safe, stable operation by keeping components properly fastened

• Disconnect power (and water if applicable) before accessing interior panels
• Use the proper screwdriver or driver bit to avoid stripping the head
• Align parts before tightening and tighten until snug—do not overtighten
• Replace only with the correct OEM part to ensure proper fit and function

This relay is used on multiple types of appliances: Ranges, Cooktops, Wall Ovens, Washers and Dryers.

Color: White. For black order WP98008545. For biscuit order 98008169.

This spring support secures a suspension spring to the washer's frame, helping keep the tub stable during wash and spin. Replacing a damaged support restores proper balance control to reduce vibration and banging. What it does:

• Anchors a suspension/tub spring to the cabinet or base
• Helps control tub movement and maintain alignment during spin
• Failure can cause excessive vibration, banging, off-balance shutdowns, or a leaning tub
• Visible cracks, bent tabs, or a detached spring indicate the support needs replacement

• 1 spring support

• Disconnect power and turn off water before servicing
• Support the tub and carefully relieve spring tension before removing the old support
• Transfer the spring to the new support and install in the original location/orientation
• Wear gloves and eye protection; springs are under tension

Specs: No.8-18AB WAFER HD

Size: 10-24 x 3/8 inch.

Note: This part is one screw, order quantity needed.

This tub displacement switch monitors water level/pressure to help the washer detect tub fill and balance, reducing overfill and load sensing errors. It replaces a worn or faulty unit to restore reliable fill and balance sensing. What it does:

• Senses tub water displacement/pressure changes so the washer can detect correct fill and load balance
• Helps prevent overfilling and supports proper spin cycles by reporting tub condition to the control
• Commonly replaced when washer overfills, won't start spin, or shows erratic fill behavior

• Disconnect power before accessing internal components to avoid shock
• Mounts to the washer chassis with electrical connector and vacuum/pressure hose; reuse existing hose if undamaged
• Verify hose and fittings are intact and free of blockages before installation

This guard hose is a molded protective sleeve that shields appliance hoses from abrasion and wear, helping keep water lines routed safely and reducing the risk of chafing-related leaks. What it does:

• Protects a water or drain hose from rubbing, abrasion and sharp edges
• Helps maintain proper hose routing to reduce kinks and stress at fittings
• Minimizes wear that can lead to leaking or premature hose failure
• Supports a more reliable seal by reducing hose movement at connection points

• Disconnect power and shut off the water supply before beginning work
• Slide guard over the hose as shown in the OEM diagram
• Use basic hand tools; avoid sharp bending or cutting the guard during install
• Replace any hoses or clamps that show signs of damage or corrosion

This electronic control board regulates the appliance's functions and user controls so the unit runs cycles and displays status correctly. Replaces a failed control board to restore normal appliance operation and control responsiveness. What it does:

• Manages timing, cycle selection, and user interface commands for the appliance
• Communicates with sensors and actuators to start and stop cycles
• Can resolve symptoms like unresponsive controls, incorrect cycle operation, or error codes tied to the main control
• Works as the central logic module coordinating other control components

• One electronic control board

• Disconnect power before servicing to avoid shock or damage
• Handle the board by its edges and avoid static discharge; use an anti-static strap if available
• Verify cabinet access panels and connectors match before installing the replacement

A single pop rivet used to secure sheet-metal parts and small brackets on appliances for a permanent, vibration-resistant hold. Replaces missing or damaged rivets to restore proper attachment without welding. What it does:

• Provides a permanent blind-rivet fastening point for panels, brackets and trim.
• Replaces rivets that are sheared, loose or missing and prevents rattling or misalignment.
• Ideal where a solid, tamper-resistant join is required and screws aren't suitable.
• Works with a compatible pop-rivet tool for quick installation.

• Drill out the old rivet carefully; use the proper size hole for the replacement rivet.
• Use a dedicated pop-rivet tool and wear eye protection during installation.