Msd265oheb Parts

This hose clamp secures a rubber or plastic hose to its fitting on your appliance, maintaining a tight, leak-resistant seal under vibration and pressure. Replace when the old clamp is rusted, bent, or no longer holds tension. What it does:

• Clamps around a hose to grip the fitting and seal the joint
• Helps prevent drips, leaks, and hose blow-off at the connection
• Restores secure clamping force when the original is worn or damaged
• Common symptoms: water at the connection, hose slipping off, visible corrosion or distortion

• 1 hose clamp

• Disconnect power and shut off the water supply before servicing
• Slide clamp onto hose, seat hose fully on the fitting, then position clamp just behind the bead/raised lip
• Tighten or compress evenly with the appropriate tool; avoid overtightening that could damage the hose
• After reassembly, run a short test and inspect for leaks

This temperature control thermostat regulates the refrigerator compartment temperature by cycling the cooling system on and off. Replacing a faulty control restores consistent cooling and normal on/off operation so food stays at the right temperature.

• Senses compartment temperature and opens/closes electrical contacts to start or stop cooling
• Useful when the fridge is too warm or too cold despite adjustments
• Common symptoms: runs constantly or won't run, temperatures don't respond to the dial, no click or change when turning the control
• Also called a "cold control"; restores functional temperature adjustment

• Disconnect power before servicing
• Note wire locations and transfer them to the new control
• Carefully route the sensing capillary in the original path; avoid kinking or sharp bends
• Set to a mid-range setting and allow up to 24 hours for temperatures to stabilize

Color: white. Measures about 2/3 of an inch wide by 1/2 an inch deep.

Color: Apollo Grey

This electronic control board manages the appliance's functions and user interface, restoring normal operation when the original board fails. It replaces a faulty control module to help re-enable cycles, settings, and display feedback. What it does:

• Receives input from the control panel and sensors to run timed cycles and selected options
• Controls power delivery, timers, and cycle sequencing for proper operation
• Can cause error codes, unresponsive buttons, or intermittent operation if damaged

• One electronic control board (main control board) as shown

• Disconnect power before removing or installing the control board to avoid shock or damage
• Handle the board carefully; avoid touching circuitry and use anti-static precautions when possible
• Verify the board mounting, wiring harness connections, and connectors seat fully during installation

This small rubber grommet cushions and supports a fan motor, helping reduce vibration and noise while the appliance is running. It fits into the motor bracket to provide a snug, insulated mounting point.

• Isolates fan motor vibration to cut rattling or buzzing
• Helps keep the motor aligned in its bracket
• Can wear, crack, or compress over time, causing vibration or noise
• Replacing a deteriorated grommet restores smooth, quieter operation

• Disconnect power before servicing
• Access the fan assembly and support the motor to relieve strain
• Note grommet orientation; transfer any sleeves or hardware as found
• Seat the new grommet fully in the bracket before remounting the motor

This white dispenser fountain bracket secures the small collection/fountain area beneath the refrigerator dispenser, restoring proper alignment and support for the dispenser assembly. It's a direct-replacement part used where the fountain bracket is broken or loose. What it does:

• Supports and secures the dispenser fountain/collection tray to the cabinet or dispenser housing.
• Keeps the fountain aligned so the dispenser fits flush and stays stable during use.
• Commonly replaced when the fountain or surrounding area is loose, cracked, rattles, or does not sit flush.
• Works with the dispenser housing components to maintain proper water/ice flow direction.

• Disconnect power to the refrigerator before beginning any work.
• Access may require removing the dispenser bezel or interior liner; save and reuse any mounting hardware if undamaged.
• Install with care to avoid overtightening fasteners or damaging adjacent plastic parts.

This 115V water valve controls water flow through the refrigerator filter assembly so ice and the dispenser get clean, pressurized water when needed. Replaces a failed valve to restore normal water delivery and stop unwanted leaks. What it does:

• Opens and closes the water supply to the refrigerator filter when the dispenser or ice maker calls for water
• Restores water flow if the dispenser or ice maker has little or no water
• Stops internal leaks when a faulty valve is the source of seepage or continuous water flow
• Operates on a 115V electrical feed used by the filter valve circuit

• One 115V water valve for the filter assembly

• Disconnect refrigerator power and shut off the water supply before beginning
• Relieve water pressure and have a towel handy for residual water in lines
• Verify valve electrical connections and tubing fittings are secure and properly seated
• Test for leaks and proper operation after installation; follow factory service instructions for detailed steps

This assembly contains the evaporator defrost heater and temperature thermostat that remove frost from the evaporator coil to help restore normal cooling. Replaces failed defrost components to help the fridge complete defrost cycles and reduce ice buildup. What it does:

• Heats the evaporator during defrost cycles so accumulated frost melts away
• Uses a temperature thermostat to open/close the heater circuit at the correct temperature
• Commonly replaces failed defrost parts when frost builds on the evaporator or the refrigerator runs continuously
• Helps restore normal airflow and cooling when defrost cycle has stopped functioning

• One defrost heater and thermostat assembly

• Disconnect power to the appliance before starting any repair
• Handle the evaporator and fins carefully to avoid damage; keep electrical connections secure and dry
• Follow the manufacturer instructions for routing and mounting the assembly

This glass refrigerator shelf provides a stable, easy-to-clean surface for storing food and containers inside the fresh-food compartment. It restores proper shelving layout and helps keep items organized and visible. What it does:

• Replaces a broken, cracked or missing glass shelf so food and containers sit level and secure
• Helps contain spills on a wipe-clean surface to simplify cleanup
• Restores usable storage space and original shelf configuration
• Fits into existing shelf supports and works with standard refrigerator shelf clips or rails

• One glass shelf

• Slide shelf into existing support rails or clips; no special tools typically required
• Handle with care — glass edges can be sharp; wear gloves during installation
• Verify shelf is fully seated and level before loading with heavy items
• If shelf clips or rails are damaged, replace them to ensure secure fit

This replacement water-dispensing lever restores a refrigerator's push-activated water control so you can dispense water easily and reliably. Fits the dispenser paddle area and matches the appliance's white finish. What it does:

• Replaces a broken or cracked dispenser lever so the water paddle can be pressed comfortably
• Transfers user pressure to the internal water valve or actuator to start water flow
• Helps stop intermittent leaks caused by a damaged or misaligned lever
• Restores proper feel and alignment for consistent dispensing

• One water dispenser lever (white)

• Inspect the dispenser area and valve linkage before installing
• Typically secures with a snap-fit or a small screw; handle gently to avoid cracking plastic
• Disconnect power at the appliance and shut off the water supply before service for safety

This door shelf trim (retainer bar) snaps across the front of a refrigerator door bin to keep bottles and condiments secure. Replace a cracked or missing rail to restore safe storage and prevent items from falling when the door opens.

• Secures items on the door shelf/bin and helps prevent spills during normal use
• Replaces broken, cracked, warped, or missing trim that won't stay attached
• Helps the door close without interference from loose items
• Typical symptoms: items fall from the door bin; rail is loose, damaged, or missing

• Empty the door bin before servicing
• Release the old trim by disengaging the end tabs or clips; pull outward to remove
• Align the new trim with the bin slots and snap both ends in evenly—do not overflex
• Inspect the door bin for cracks or worn slots that could prevent a secure fit

This condenser fan blade is the rotating plastic blade that moves air across the condenser coils to help remove heat from the refrigerator. Replacing a damaged blade restores proper airflow for more consistent cooling. What it does:

• Spins on the condenser fan motor to circulate air over condenser coils
• Helps dissipate heat so the compressor and fridge run efficiently
• Can cause reduced cooling or higher temperatures if broken or missing

• Disconnect power to the appliance before starting any service
• Inspect the fan motor shaft and mounting for wear; replace motor if shaft is damaged
• Handle the blade carefully to avoid cracking; ensure blade is seated and secured before testing

Fresh freezer cabinet top hinge.