Mtf1995drw Parts

This white freezer door handle restores a secure, comfortable grip and refreshes the appliance's appearance. Replace a cracked, loose, or missing handle so the freezer door opens and closes smoothly again. What it does:

• Replaces a damaged, worn, or missing freezer door handle
• Restores proper grip and leverage for normal door operation
• Helps address loose or wobbly handle conditions
• Matches the original white finish for a clean, uniform look

• Wear gloves and protect the door surface to avoid scratches
• Support the handle while loosening/removing existing fasteners
• Reuse existing hardware as designed; start screws by hand and tighten just until snug
• Check alignment and security before returning the appliance to service

This lower hinge pin is the pivot shaft for your refrigerator door. Replacing a worn or bent pin restores smooth movement and proper alignment so the door seals and closes correctly while reducing hinge noise.

• Serves as the pivot point between the door and the lower hinge bracket
• Helps maintain door height and alignment for an even gasket seal
• Wear or damage can cause door sagging, rubbing, squeaking, or inconsistent closing
• Replacing the pin can restore smooth swing and reduce wobble at the hinge

• Disconnect power; remove items from the door. Support the door and remove the upper hinge to lift the door off the lower hinge.
• Replace the lower hinge pin on the hinge/bracket, reusing any model-specific washers or bushings.
• Reinstall, level, and align the door so the gasket seals evenly; verify smooth swing and positive closure.

This PTC start relay mounts on the compressor and briefly powers its start winding to get it running, then drops out. Replacing a weak relay can restore reliable starts and resolve clicking/humming with no cooling.

• Provides the initial boost to the compressor via a positive temperature coefficient (PTC) element, then opens as it heats
• Takes the start winding out of the circuit once the compressor is running
• Typical failure symptoms: compressor won't start, repeated clicking/humming, no cooling, visible heat damage at the relay or connector
• Direct replacement for the original PTC start device used on applicable models

• Disconnect power before servicing; allow hot components to cool
• Access the compressor compartment, remove the cover, and note the relay's orientation; pull the old relay straight off the compressor pins
• Inspect wiring terminals for heat damage; do not reuse burnt connectors
• Firmly seat the new relay on the compressor terminals, reinstall the cover, restore power, and verify compressor start

Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:

• Pushes or guides harvested cubes out of the ice mold into the bin during the ice maker's harvest cycle.
• Prevents cubes from sticking in the mold; a damaged stripper can cause incomplete ejection or leftover ice in the mold.
• Works with the ice maker's ejector mechanism to maintain consistent cube release and storage.
• A faulty or broken stripper may lead to noisy operation, partial fills, or visible ice build-up in the mold.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Remove the ice maker or access panel per the manufacturer's instructions to reach the stripper; keep small parts and screws organized.
• Inspect the ice mold and surrounding components for damage or ice build-up; clear ice before installing the new stripper.
• After installation, restore power and run a test harvest cycle to ensure proper cube ejection.

This replacement roller mounting screw secures the dryer drum roller or roller bracket to keep the drum aligned. Installing the correct screw restores proper roller position and helps reduce drum wobble and rubbing noises. What it does:

• Fastens the dryer drum roller or roller bracket to the dryer cabinet or shaft
• Keeps the roller aligned so the drum rotates smoothly
• Prevents the roller from shifting, which can cause scraping, squealing, or banging noises
• Helps avoid premature wear of the roller and drum seal caused by misalignment

• Disconnect power (and gas supply for gas models) before starting any repair
• Use appropriate hand tools; avoid power drivers that may strip the screw head
• Do not overtighten — snug to secure the roller without deforming the bracket or shaft
• Inspect the roller, shaft, and mounting hardware; replace any worn components for a lasting repair

This defrost thermostat senses the evaporator coil temperature and controls the defrost heater. Replacing a failed thermostat restores proper defrosting to prevent heavy frost buildup and helps your refrigerator keep consistent, reliable cooling.

• Monitors evaporator temperature to allow the defrost heater to energize and to terminate the cycle as the coil warms
• Protects against overheating in the evaporator area during defrost
• Failure symptoms include frost/ice buildup on the evaporator cover, reduced airflow, fresh food section warming, or the unit not defrosting
• Typically mounts clipped to the evaporator tubing inside the freezer

• Disconnect power before servicing and remove the freezer's rear panel to access the evaporator
• Transfer the clip/bracket if present and mount the new thermostat in the same location, ensuring firm metal-to-metal contact with the evaporator tubing
• Route wires away from the heater and moving parts; secure connections and reassemble panels before restoring power
• Wear cut-resistant gloves—sheet-metal edges can be sharp

This heater clip secures the defrost heater in your refrigerator. Keeping the element properly positioned helps the defrost system work as designed and reduces rattling or damage from a loose or misaligned heater.

• Holds the defrost heater securely in place on its mounting point
• Helps maintain correct heater placement for consistent frost removal
• Replace if the clip is missing, broken, bent, or corroded
• Common symptoms include a loose/dangling heater, rattling noises, or recurring frost/ice around the evaporator area

• Disconnect power before servicing the appliance
• Access the defrost heater behind the freezer's rear panel; note the original clip orientation
• Install the new clip so the heater is seated and not contacting wiring or plastic; do not deform the element or coils
• Restore power and verify the heater is secured in place

Kit was recently redesigned by manufacturer. Instructions included.

This fresh food door gasket seals the refrigerator compartment door to keep cold air in and warm air out. Replacing a worn gasket restores a tight seal, improves temperature stability, and helps prevent condensation and frost around the door.

• Seals the perimeter of the fresh food (refrigerator) door to limit air leaks
• Helps maintain proper interior temperature and efficiency
• Typical symptoms of failure: door not closing or sealing fully; visible tears, gaps, or warping
• May cause moisture, sweating, or frost near the door gasket area

• Disconnect power before servicing
• Warm and relax the new gasket (soak in warm water or use low heat) to ease installation; do not overheat
• Clean the door's gasket channel; install starting at the corners and ensure even seating all around
• Close the door and check for uniform contact; use a paper-slip test to confirm the seal

This is the refrigerator's sealed-system compressor. It pressurizes and moves refrigerant through the system to remove heat from the cabinet, restoring consistent cooling performance when the original compressor has failed or lost capacity. What it does and common symptoms:

• Pumps and circulates refrigerant through the evaporator and condenser to remove heat
• Maintains target temperatures in both fresh food and freezer sections
• Symptoms of failure can include: no cool/poor cooling, unit warms up after short operation, humming then clicking from the compressor area, or repeated thermal overload trips
• Runs but not cool effectively when the compressor is weak or internally damaged (after ruling out start components and charge issues)

• 1 compressor

• Disconnect power before servicing; sealed-system work involves high pressure and high temperatures
• Sealed-system repairs require EPA Section 608 certification and specialized tools (gauges, vacuum pump, brazing equipment)
• Replace the filter-drier, braze connections properly, evacuate to deep vacuum, and charge to the model's specification
• Related components (start device/overload, run capacitor, controls) are tested before condemning the compressor

This support mounts in the dispenser area to secure the ice housing assembly. It helps keep the chute and door properly aligned so ice dispenses smoothly and the opening seals as designed.

• Supports and positions the ice housing/chute assembly in the freezer door
• Helps maintain proper alignment and sealing of the ice door/flapper
• Reduces wobble or flex that can affect dispensing performance
• Typical signs it may be needed: loose or misaligned dispenser housing, ice or air leaking at the chute, frost buildup around the dispenser, inconsistent ice dispensing

• Disconnect power to the refrigerator before servicing
• Remove the dispenser trim/control to access the housing; handle wiring and tabs carefully
• Remove mounting fasteners, replace the support, and transfer any reusable hardware
• Reassemble, restore power, and test ice dispensing and chute seal

Size: 8 x 1-1/4 inch.

This replacement mounting screw secures appliance panels and components to restore proper fit and reduce rattling. Use when a damaged or missing screw causes loose trim, gaps, or vibrating noises; order by part number to ensure a match. What it does:

• Fastens panels, brackets, or trim to keep parts aligned and secure.
• Stops vibration and rattling caused by loose or missing screws.
• Common symptoms: visible gaps, loose panels, hardware falling out, or excess noise.
• Use the part number and/or existing screw to ensure correct size and thread before ordering.

• Disconnect power and water before accessing internal components.
• Use the correct screwdriver or bit to avoid stripping the head.
• Turn until snug; avoid over-tightening which can strip threads or crack trim.
• Keep small parts away from children and pets during repair.

This radiant defrost heater melts ice build-up on the evaporator coil so your refrigerator can maintain proper airflow and cooling. It restores normal defrost operation and helps prevent excessive frost accumulation. What it does:

• Radiant heating element designed to melt frost and ice from the evaporator coil during the defrost cycle
• Restores airflow and consistent cooling when the evaporator has been restricted by ice
• Common symptom: visible frost or ice on evaporator or in freezer compartment
• Common symptom: poor or uneven cooling, longer run times, or a freezer that cycles abnormally

• One radiant defrost heater (single unit as shown)

• Disconnect power to the appliance before servicing to avoid shock risk
• Access typically requires removing the evaporator cover; handle evaporator fins and heater carefully
• Inspect defrost thermostat/thermistor and defrost control components while replacing the heater — replace only the failed components

This hinge supports and pivots the washer lid so it opens and closes smoothly. Replacing a worn or broken hinge restores proper alignment and helps the lid close securely without binding or rubbing.

• Provides the pivot point for the lid to open and close
• Keeps the lid aligned with the top panel
• Wear symptoms include wobble or sagging, squeaks, binding, or visible cracks/bending
• Misalignment may prevent the lid switch/latch from engaging properly

• Unplug the washer before servicing; have a helper support the lid
• Remove the mounting screws, noting hinge orientation for reassembly
• Transfer and reuse original screws/trim as applicable; do not overtighten
• Test lid alignment and operation before fully tightening the fasteners

This replacement screw secures panels, brackets, or trim on compatible Whirlpool appliances to restore proper fit and reduce rattles and movement. Use it when a fastener is missing, loose, or stripped. What it does:

• Secures appliance panels, trim pieces, brackets, or small components in place
• Restores proper fit to eliminate rattling, gaps, or shifting parts
• Replaces missing, worn, or damaged screws that compromise mounting
• Matches OEM form and function when the correct screw is specified for the repair

• Turn off power to the appliance before working near controls, heating elements, or wiring
• Use the correct screwdriver or bit to avoid stripping the head; do not overtighten
• Keep removed screws in a container to ensure none are lost during reassembly