Mvw8700vq0 Parts

The Lid Lock Bezel (White) is an OEM replacement part for Whirlpool washers. The bezel provides an aesthetic covering for the lid lock mechanism located on top of the washer. 

Causes of a bad bezel can include normal wear and tear from repeated use of the washer lid over time. Scratches, cracks or splits in the plastic material are also possible from accidental impact or drops.

Symptoms of a bad bezel include:

• Cosmetic flaws like discoloration, scratches or cracks that diminish the appearance of the washer
• Looseness, rattling or misalignment of the bezel covering 
• Difficulty opening or closing the washer lid securely. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

Specs: 10-16 x 1/2 inch.

The Tub Ring is an OEM part for Whirlpool washing machines. It is an internal gasket or seal that fits securely around the outer rim of the washer tub. The tub ring works to create a watertight barrier, preventing leakage between the tub and other cabinet components like the agitator shaft or balancer. 

Causes of a bad tub ring can include warping due to heat exposure or tub filling impacts over time, cracks developing from heavy impacts or loads that stress the tub, or cuts and tears caused by debris lodged inside the ring.

Symptoms of a bad tub ring include: 

• Water leaks appearing around the tub or agitator shaft when in use
• Puddles or standing water found inside the washer cabinet 
• Difficulty getting the washer lid or door fully closed and secured
• Excessive moisture buildup inside non-tub areas 

It is also compatible with Maytag, KitchenAid, Amana, Roper, and select Kenmore models.

The Coin Slide Interface is an OEM part for Whirlpool commercial washers. It is a component that allows users to insert coins or tokens to activate the machine and initiate the laundry cycle.

Causes of a faulty coin slide interface can include regular wear and tear, damage due to misuse or vandalism, or electrical component failure. These factors can result in issues such as coin rejection, incorrect coin counting, or the inability to start the machine using coins.

Symptoms of a Bad Part:

• Will not start
• Not washing properly
• Timer will not set

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This bleach dispenser stores liquid chlorine bleach and automatically dilutes and releases it at the correct point in the wash cycle. Replacing a cracked or clogged dispenser helps stop leaks, protect fabrics, and restore consistent bleaching performance.

• Holds bleach and siphons it into the tub at the proper time in the cycle
• Helps prevent undiluted bleach from contacting fabrics early
• Direct replacement for a dispenser that is cracked, warped, or clogged
• Address symptoms such as bleach remaining in the cup, dispensing too soon, leaks near the dispenser area, or fabric spotting

• Disconnect power and turn off water before servicing
• Access the dispenser through the top/console area; remove fasteners and detach connected hose(s)
• Transfer any hoses, clamps, and mounting hardware from the original part; ensure all connections are fully seated to prevent leaks
• Run a test/rinse cycle to check for leaks

This is a washing machine gearcase. The purpose of the gearcase is to drive the agitator and spin the basket within the washing machine. When the gearcase stops working correctly, the water may not drain from the clothing after the spin cycle. The user may also notice a burning odor that comes from the washing machine while it's in operation. Sometimes, the washing machine will attempt to agitate and run the spin cycle at the same time. If this is the case, the gearcase needs to be replaced. The appliance will need to be unplugged before replacing this part. Wear gloves to protect the hands for this process.This component is compatible with washing machines that are manufactured by Whirlpool, Kenmore, and Maytag. It is sold individually. This is a genuine OEM replacement part that comes straight from the manufacturer. It's high quality and made to last.

The Dispenser is an OEM part for Whirlpool washing machines. It holds and dispenses detergent for each wash load through the drawers located on the washer's console panel. 

Symptoms of a bad dispenser include:

• Improper or incomplete dispensing of detergent
• Detergent residue accumulated inside the dispenser 
• Drawers not opening or closing as intended

Causes of a dispenser failure can be due to worn components, mineral buildup interfering with mechanics, or damage from moisture exposure over time. 

Replacing with a new OEM dispenser restores optimal detergent delivery for every cycle. This ensures clothes are fully cleaned and rinsed without risk of detergent residue.  

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This lock cam is a small actuator that drives the appliance's door-lock mechanism. It translates the lock actuator's movement into a positive latch, helping the door lock securely when required and release correctly so cycles start and finish properly.

• Interfaces with the lock actuator and latch to engage and release the lock
• Wear, cracking, or rounding can cause the lock not to engage or to stick
• Common symptoms include a door/lid that won't lock or unlock, loose lock lever, clicking without latching, or door/lock-related error messages
• Restores proper linkage travel and switch actuation when the original cam is worn or damaged

• Disconnect power to the appliance before servicing
• Access the lock mechanism per your model; note the cam's orientation and any springs/linkages
• Install the new cam fully seated and ensure it engages the actuator and latch smoothly
• Reassemble, restore power, and test lock operation

This rotary encoder mounts behind the washer's cycle knob and tells the main control which setting you select. When it fails, selections may be erratic or unresponsive. Replacing it restores accurate, dependable cycle selection. What it does

• Detects the position of the cycle selector knob
• Sends selection signals to the main control board
• Enables precise cycle and option changes
• Common symptoms: knob turns but lights don't follow, random/incorrect selection, can't select a cycle, won't start

• One rotary encoder

• Disconnect power to the washer before servicing
• Access the control console and remove the knob/dial to reach the encoder
• Note orientation, unplug the harness, release tabs/screws, and swap in the new encoder
• Handle electronics carefully and avoid static discharge; verify knob-to-light tracking before reassembly

When replacing this part, if you see that your motor stator is broken, search by your model number to make sure you get the right stator for your model. NOTE: Also includes Rotor Bolt. The bolt is not available separately.

This leveling foot stabilizes and levels your appliance on uneven floors. It threads into the base so you can raise or lower a corner, reducing rocking and vibration for smoother, quieter operation and proper alignment.

• Provides precise height adjustment to level the cabinet
• Helps prevent wobble, walking, or rattling during use
• Supports stable operation and proper door alignment
• Replaces a missing, stripped, or damaged foot

• Disconnect power; shut off gas/water if applicable
• With help, carefully tilt or brace the appliance to access the foot
• Thread the new foot in by hand, then fine-adjust with a wrench until level and stable
• Ensure all feet contact the floor; recheck level after positioning

This washer drain hose routes wastewater from the drain pump to your home standpipe or laundry tub. Replacing a cracked, kinked, or clogged hose helps stop leaks and restores proper draining so cycles complete reliably.

• Directs discharge water from the washer to the household drain
• Maintains proper flow when correctly routed and secured
• Common symptoms: water leaking at the rear/under the washer, slow or no drain, long-drain errors, visible cracks or kinks
• Visible wear, brittleness, or residue buildup on the hose indicates replacement is needed

• Unplug the washer and move it for rear access; place towels or a pan to catch residual water
• Loosen clamps/fasteners and disconnect the old hose from the pump and drain connection; note the original routing
• Install the new hose in the same orientation; avoid kinks and secure all connections firmly
• Position the outlet per your model's instructions to prevent siphoning; run a test drain and check for leaks

This fresh-water nozzle assembly directs a controlled stream into the appliance during fill/dispense. Replacing a cracked or clogged nozzle restores proper flow and helps reduce splashing, misdirected spray, or dripping at the opening. What it does:

• Shapes and directs fresh water into the tub/dispenser area
• Helps prevent spray, backflow, and mess around the opening
• Common symptoms: weak or misdirected stream, dripping after fill/dispense, leaks near the opening, visible cracks or mineral buildup on the nozzle
• A kinked or brittle attached tube can restrict flow or leak

• One fresh-water nozzle assembly

• Disconnect power and shut off the water supply before servicing
• Access the nozzle area; remove necessary panels or trim
• Release retaining clip(s), disconnect tubing, and note routing before removal
• Install the new assembly fully seated; restore water/power, check for leaks, and run a test fill to flush air/debris

Color: Grey

The Lid Lock Bezel is an OEM replacement part for Whirlpool washing machines. 

Symptoms of a need to replace the bezel include:

• Cracks, discoloration, or visible damage to the bezel
• Looseness or detachment of the bezel from the panel

Causes of a damaged or worn bezel can include accidental impacts, exposure to cleaning chemicals, or general wear and tear over time.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models.

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit