Mvwb7258wo Parts

This recirculation hose routes wash water back through the tub during the cycle. A fresh, intact hose helps maintain proper water flow and prevents leaks, supporting consistent cleaning performance.

• Directs water from the pump back into the tub for continued circulation
• A cracked, kinked, or leaking hose can cause water leaks or poor wash performance
• Can help resolve issues like low recirculation flow or visible water drips during operation
• Restores correct internal water routing as designed

• Disconnect power and water supply before servicing
• Have towels or a shallow pan ready to catch residual water
• Note hose routing and clamp positions before removal; reuse or replace clamps as needed
• After installation, run a quick cycle to check for leaks and proper flow

Restore smooth ice and water dispensing with this refrigerator dispenser assembly in a stainless finish. It replaces the in-door dispenser module so a cracked housing or broken lever no longer hinders operation or appearance.

• Serves as the user-facing ice/water dispenser module mounted in the door
• Provides the paddle/actuator and support for the dispenser's components
• Helps resolve: broken or sticking lever, cracked/loose dispenser housing, nonresponsive dispenser when pressed, cosmetic damage to the dispenser area
• Direct, model-specific replacement; matches the stainless finish

• Disconnect power and shut off the water supply before servicing
• Carefully remove the dispenser trim/panel to avoid scratching the finish; retain screws and clips
• Transfer wiring connectors and any reusable parts from the original assembly per your model's parts list
• Restore power/water and test both ice and water dispensing; check for proper actuation and leaks

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This recirculation pump assembly drives water through the appliance's circulation system, maintaining steady flow and pressure for proper operation. Replace it if water won't circulate, performance drops, or the unit becomes noisy or shows a pump-related error.

• Moves water through internal channels to maintain consistent circulation and pressure
• Helps ensure effective cleaning/operation during wash or circulation steps
• Common failure symptoms: no/weak water movement, poor results, humming or grinding noises
• Trigger pump/circulation error messages or cause cycles to stall

• Disconnect power and shut off water supply before servicing
• Access is typically from the bottom/front; remove toe-kick or lower panels as needed
• Expect residual water; protect the area and transfer clamps/fittings from the old pump if required
• Seat any seals properly, reconnect hoses/wiring securely, and test for leaks and proper circulation

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Contains two, six foot long braided hoses with 90 degree ends.

This replacement detergent dispenser assembly mounts in the dishwasher door and releases detergent at the correct time in the cycle to help ensure thorough cleaning and consistent wash results. What it does:

• Holds and seals detergent until the control signals it to open
• Releases detergent into the tub for proper wash performance
• Common failure symptoms: detergent left in cup, dispenser door won't latch or open, leaks around the dispenser area, or poor cleaning due to no detergent release

• One detergent dispenser assembly

• Disconnect power and turn off water supply before servicing
• Remove the inner door panel to access the dispenser retainers
• Release the old dispenser, transfer any electrical connector(s), and seat the new dispenser evenly to ensure a watertight seal
• Reassemble, run a short cycle, and check for leaks around the dispenser

This nozzle assembly directs fresh water for the refrigerator's fresh-fill function, restoring controlled filling and helping prevent leaks and drips. Replace a damaged nozzle to restore reliable water dispensing. What it does:

• Directs and meters fresh water flow during the refrigerator's fill cycle.
• Helps prevent water from spraying or dripping away from the intended fill area.
• Common symptoms for replacement: visible leaks, dripping after fills, inconsistent or no water during fill cycles.
• Interfaces with the fridge water tubing and fill valve to deliver proper flow.

• Disconnect power to the appliance before starting any repair.
• Shut off the water supply and drain residual water to avoid spills.
• Replace using basic hand tools; ensure proper seating and secure connections to avoid leaks.

Color: White

This control knob replaces a worn or broken knob so you can reliably set and adjust your appliance's settings again. It restores a smooth, positive feel and clear pointer alignment for everyday use.

• Selects and adjusts the matching control (such as burner, temperature, or function) on the appliance
• Worn, cracked, or missing knob can make settings hard to change or read
• Loose or slipping knob may prevent the control shaft from turning properly
• Cosmetic damage can detract from the appliance's appearance

• Disconnect power and allow hot surfaces to cool before servicing
• Pull the old knob straight off the control shaft; do not twist against stops
• Align the flat or D-shaped opening with the shaft and press firmly until seated
• If the knob won't seat, inspect the shaft for damage or debris before reinstalling

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

Used from harness to top.