Mvwp575gwd Parts

This cap seal creates a tight barrier between a cap and its mating surface in your appliance. Replacing a worn seal restores a secure, leak-resistant fit and helps maintain proper performance over time.

• Forms a tight seal where the cap seats to prevent leaks and seepage
• Helps maintain intended pressure/flow and keeps contaminants out
• Typical failure signs: drips or moisture around the cap area, loose cap fit, or a flattened/cracked seal
• Age, heat, and detergents/chemicals can harden or deform the seal

• Disconnect power and shut off water before servicing
• Remove the cap and note the seal's orientation
• Clean mating surfaces; seat the new seal fully without twisting
• Reinstall the cap and test operation, checking for a leak-free fit

This rotary encoder mounts behind the washer's cycle knob and tells the main control which setting you select. When it fails, selections may be erratic or unresponsive. Replacing it restores accurate, dependable cycle selection. What it does

• Detects the position of the cycle selector knob
• Sends selection signals to the main control board
• Enables precise cycle and option changes
• Common symptoms: knob turns but lights don't follow, random/incorrect selection, can't select a cycle, won't start

• One rotary encoder

• Disconnect power to the washer before servicing
• Access the control console and remove the knob/dial to reach the encoder
• Note orientation, unplug the harness, release tabs/screws, and swap in the new encoder
• Handle electronics carefully and avoid static discharge; verify knob-to-light tracking before reassembly

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

This pump drain filter helps protect the appliance's drain pump by screening out debris before it enters the pump. A clean, intact filter supports proper draining and helps prevent clogs and pump damage.

• Screens debris before it reaches the drain pump
• Helps maintain proper draining performance
• May resolve issues like slow or incomplete draining, standing water, or drain-related noises
• Replacing a damaged or missing filter can reduce repeat clogs

• Unplug power and shut off water supply before service
• Access location varies by model; have towels ready for any residual water
• Note orientation of the old filter for correct placement
• After installation, check for leaks and run a brief drain cycle to verify operation

The CAM-AGIT is an OEM part for Whirlpool washers. It is the camshaft and agitator assembly that is located inside the wash basket. The cam-agit assembly is responsible for the wash cycle's filling, flushing, scrubbing, and spinning motions. 

Causes of a bad cam-agit assembly can include wear and tear over time, damage due to impact, or imbalanced loads. Over many cycles the plastic parts can crack or the motor can fail causing improper movement.

Symptoms of a bad cam-agit assembly include: 

• Inability to properly fill or empty water
• No or weak agitation during scrubbing cycles 
• Loud noises or vibrations during spinning 
• Water not draining completely after cycles

This OEM Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Coupler is an OEM part for Whirlpool washing machines. It connects the agitator shaft to the transmission or drive system of the washer, allowing rotation to be transferred from the motor to the agitator during the agitation cycle.

Causes of failure can be repetitive stress and strain from years of use, which causes wear and weakening of the coupler material over time. Damage due to rust or corrosion is also possible if water enters the transmission housing.

Symptoms of a bad agitator coupler include:

• Agitator not spinning or rotating during the wash cycle
• Excessive noise coming from the transmission or drive area
• Vibration issues
• Loose or wobbly agitator

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This lid hinge pad fits between the washer lid hinge and the cabinet. It cushions the joint to reduce squeaks and metal wear, helping keep the lid aligned and operating smoothly.

• Provides a protective wear surface between the hinge and cabinet/lid
• Reduces squeaks, creaks, and rattling when opening or closing the lid
• Helps maintain proper lid alignment and smooth movement
• Common signs it's worn or missing: squeaking lid, rubbing/scuff marks at the hinge, loose or wobbly lid

• Disconnect power to the washer before servicing
• Support the lid to relieve hinge tension and access the hinge area per your model
• Remove the worn pad and press the new pad fully into the hinge location
• Test lid operation; inspect the opposite hinge and replace its pad as needed if your model uses two

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

The Drive Motor is an OEM part for Whirlpool washing machines. The drive motor is responsible for powering the agitator or impeller as well as drum rotation during all cycles. It converts electrical energy into mechanical motion needed for washing and spinning laundry.

Causes of a bad drive motor can include failure to start, inconsistent speeds or intermittent operation which are tell-tale signs of normal wear and tear over time.

Symptoms of a failed drive motor include:

• The washer not starting or completing cycles
• Abnormal sounds such as grinding or clicking during operation
• Noticeable vibrations compared to typical wash cycles
• Inability to spin or properly agitate clothing

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This lower console harness routes power and signals between the console control area and the appliance's lower components, restoring reliable electrical connections for controls and indicators. Use this harness to replace damaged or worn wiring in the lower console. What it does:

• Carries control and power circuits between the lower console and internal components
• Replaces frayed, pinched or broken wiring that can cause intermittent or failed console functions
• Helps resolve symptoms such as unresponsive console buttons, missing indicator lights, or intermittent operation related to lower-console wiring
• Maintains correct connector routing and secure plug connections for consistent performance

• Disconnect power to the appliance before starting any repair to avoid shock hazard
• Access the lower console per the service guide; remove panels and fasteners as needed to reach the harness routing
• Match connector shapes and colors; fully seat each plug and secure any routing clips or ties
• Inspect surrounding wiring and components for damage while replacing the harness

This agitator cam is the replacement cam that fits under the washer agitator to engage the transmission and help transfer motion. Replacing a worn or broken cam restores secure agitator engagement for reliable washing action. What it does:

• Locks the agitator to the drive so the agitator oscillates and reverses during wash cycles
• Replaces a damaged or worn cam that can cause the agitator to slip, spin freely, or fail to agitate
• Works with the agitator assembly and dogs to maintain proper drive engagement
• Restores proper mechanical linkage between the agitator and the washer transmission

• Disconnect power and water supply before beginning any repair
• Remove the agitator, inspect agitator dogs and splines for wear, and replace if needed
• Install the cam into the agitator and reassemble in reverse order of removal following the OEM service instructions
• After reassembly, run a short test cycle to ensure the agitator engages and functions correctly

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This pushbutton installs in the control console and actuates the underlying switch, restoring positive, reliable selection of a cycle or feature and a clean, finished appearance when the original button is worn, sticky, or broken. What it does

• Provides the user-facing cap that presses the internal control switch
• Restores smooth button travel and positive engagement
• Helps ensure selections register consistently
• Common symptoms: button cap cracked/missing, sticks or won't spring back, selection only registers when pressed hard, loose or wobbly button

• 1 pushbutton

• Disconnect power before servicing to avoid electrical shock
• Access the control/console per your service manual
• Note orientation; release retaining tabs and remove old button
• Seat the new button fully; test travel and function before reassembly

Includes connector and both clamps.

The Capacitor is an OEM part for Whirlpool washers. It is responsible for starting the motor and keeping it running smoothly during the washing cycle. It stores electrical energy and delivers it to the motor when needed, providing the necessary power for the washer to function properly.

A bad washer capacitor can occur due to electrical malfunctions, wear and tear, or damage to the capacitor itself. If you notice symptoms such as the washer not starting or spinning, the motor making unusual noises, or the washer not completing cycles, it may be time to replace the washer capacitor.

Symptoms of a bad washer capacitor include:

• Washer not starting or spinning
• Unusual noises coming from the motor
• Incomplete cycles or erratic behavior

Repair your washer by replacing the faulty or worn-out washer capacitor with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.