Pig23mimhfkb Wr55x10556 Parts
Genuine Ge part
By: Ge
Part Number: WR55X10025
The Temperature Sensor is an OEM replacement part for GE refrigerators, designed to accurately monitor and relay the temperature inside the refrigerator and freezer compartments to the electronic control board. By detecting the slightest changes in internal temperature, the sensor allows the control board to make real-time adjustments to the cooling system, activating the compressor and fans as needed to maintain optimal conditions for food preservation.
Over time, the temperature sensor can fail due to electrical issues, exposure to moisture, or general wear and tear. A malfunctioning sensor can lead to improper temperature regulation, affecting the efficiency of the refrigerator and the freshness of stored food.
Symptoms of a bad Temperature Sensor include:
- The refrigerator or freezer not maintaining the set temperature
- The appliance running continuously or more frequently than normal
- Inaccurate temperature readings displayed
This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
This part fixes the following symptoms
-
Fridge too cold
-
Too warm
-
Fridge runs too long
-
Freezer too cold
See more...
Do-It-Yourself Stories from Customers like You
Defroster in freezer not functioning causing the freezer to frost up and the fridge to not cool appropriately Eddie R. • Debary , FL • January 06, 2015
I unplugged the fridge and took all the food and shelving out of the freezer and then proceeded to take off the bottom sliding drawer rack on both sides off (4 Phillips head screws). Then took off the light bulb cover and then the light bulb. Then the back wall that covers the coils and tubes that the refrigerant runs through ( 2 screws with hex head). After sliding out the back wall I could see that the entire coil area was frosted and iced up. I took a blow dryer and melted all of it over...
Read more
More
$16.30
- Compare At:
-
$22.39
- You Save:
-
$6.09
Genuine Ge part
By: Ge
Part Number: WR50X10068
The Defrost Thermostat is an OEM replacement part designed for use in GE refrigerators. This component acts as a safety device in the refrigerator's defrost system, preventing the freezer from overheating during the defrost cycle. It works by monitoring the temperature of the evaporator coil and turning off the defrost heater when the coil gets warm enough, thus safeguarding the freezer from getting too hot.
Causes of a bad defrost thermostat can include corrosion, a blown fuse inside the thermostat, or wear and tear over time, which can lead to malfunctioning of the refrigerator's defrost system.
Symptoms of a bad Defrost Thermostat include:
- Frost buildup on the back wall of the freezer
- The refrigerator is not cooling properly
- The freezer is cold but the refrigerator is warm
- The defrost heater not turning on
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
Freezer not defrosting
-
Freezer too cold
-
Not dispensing water
-
Ice maker not making ice
See more...
Do-It-Yourself Stories from Customers like You
Defroster in freezer not functioning causing the freezer to frost up and the fridge to not cool appropriately Eddie R. • Debary , FL • January 06, 2015
I unplugged the fridge and took all the food and shelving out of the freezer and then proceeded to take off the bottom sliding drawer rack on both sides off (4 Phillips head screws). Then took off the light bulb cover and then the light bulb. Then the back wall that covers the coils and tubes that the refrigerant runs through ( 2 screws with hex head). After sliding out the back wall I could see that the entire coil area was frosted and iced up. I took a blow dryer and melted all of it over...
Read more
More
$18.72
- Compare At:
-
$24.73
- You Save:
-
$6.01
Genuine Ge part
By: Ge
Part Number: WR02X12008
The Fan Motor Grommet is an OEM replacement part for GE refrigerators. This small but essential component serves as a seal and insulator around the area where the fan motor shaft protrudes from the appliance body.
Causes of needing to replace the fan motor grommet can include normal wear and tear over time, exposure to extreme temperatures or moisture, or physical damage due to impact or improper installation.
Symptoms of a faulty or missing grommet include:
- Air leaks or drafts around the fan motor area
- Condensation buildup or frost formation near the motor shaft
- Increased noise or vibration from the fan motor assembly
- Reduced cooling efficiency due to air leakage
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.
Do-It-Yourself Stories from Customers like You
Evaporator fan motor whining keeping me up at night then it sounded like rocks were in it Judy P. • Lakeside , CA • March 30, 2015
It was after 11:00 at night a few nights ago, I couldn't sleep listening to the whining of the fan in the freezer, it was running and making noise sounding like waaoooww, waaaoww. It also sounded like grumbling of a garbage disposal. The refrigerator fan motor was so noisy it was keeping me up all night going on and off running really loud and about to fail. So I was desperate, and called AppliancePartsPros when I couldn't get to sleep near midnight because the fan was so noisy and Bud in...
Read more
More
$7.41
- Compare At:
-
$8.82
- You Save:
-
$1.41
Genuine Ge part
By: Ge
Part Number: WR17X11653
The Ice Door Assembly is an OEM part for GE refrigerators. It is integral to the ice dispenser system, controlling access to the ice chute. This component ensures the efficient delivery of ice cubes or crushed ice when activated and seals off the chute when not in use to maintain the freezer's temperature and prevent frost buildup.
Symptoms of a bad Ice Door Assembly include:
- Frost or ice buildup around the dispenser area
- Ice escaping from the dispenser when not in use
- Failure to dispense ice
- Noise during operation indicating misalignment or malfunction
Causes of a bad Ice Door Assembly can include mechanical wear from frequent use, failure of the spring mechanism or solenoid that operates the door, or damage to the sealing surfaces that leads to air leaks.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
Door sweating
-
Frost buildup
-
Ice maker won't dispense ice
-
Freezer not defrosting
See more...
Do-It-Yourself Stories from Customers like You
Ice flapper door stopped closing Lawrence D. • Holly Springs , NC • March 21, 2016
My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser...
Read more
More
$11.95
- Compare At:
-
$14.34
- You Save:
-
$2.39
Genuine Ge part
By: Ge
Part Number: WR62X10055
The Ice Dispenser Solenoid is an OEM replacement part for GE refrigerators. It is a crucial component that controls the flow of ice from the ice maker to the dispenser chute.
Symptoms of a bad ice dispenser solenoid include:
- Failure to dispense ice from the dispenser
- Ice getting stuck or jammed in the dispenser chute
- Continuous flow of ice even when the dispenser is not activated
Causes of a bad solenoid can include electrical malfunctions, physical obstructions preventing proper operation, or simply wear and tear over time.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
Ice maker won't dispense ice
-
Door sweating
-
Frost buildup
See more...
Do-It-Yourself Stories from Customers like You
Ice flapper door stopped closing Lawrence D. • Holly Springs , NC • March 21, 2016
My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser...
Read more
More
$48.33
- Compare At:
-
$57.56
- You Save:
-
$9.23
Genuine Ge part
By: Ge
Part Number: WR17X11440
The Water Tank Assembly is an OEM part for GE refrigerators, designed to store and chill water before it's dispensed through the refrigerator's water dispenser. This integral component ensures that you have immediate access to cold, fresh water without the need to open the refrigerator, helping to conserve energy and maintain the internal temperature.
Over time, the water tank assembly can experience issues such as leaks, cracks, or the buildup of contaminants, all of which can affect the quality and taste of your water.
Symptoms of a bad Water Tank Assembly include:
- Leaks or puddling water beneath the refrigerator
- A noticeable drop in water flow from the dispenser
- Unpleasant taste or odor in the dispensed water
- Visible cracks or damage to the tank or its connections
This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
Do-It-Yourself Stories from Customers like You
Water tank leak Gordon T. • Jonesboro , AR • January 27, 2017
Our refrigerator takes care of my wife and I, along with our children when they visit, and the grand kids. Over the years, it's seen its fair share of wear and tear. Thankfully, nothing major has happened that hasn't been able to be repaired right here in the home, and by me. Our refrigerator is a GE side-by-side with an ice maker/water dispenser, and has held up well. I've ordered parts for it from AppliancePartsPros.com for all of its repairs, and while GE/Frigidaire have been changing out a...
Read more
More
$42.34
- Compare At:
-
$50.81
- You Save:
-
$8.47
Genuine Ge part
By: Ge
Part Number: WR60X10185
The Evaporator Fan Motor is an OEM part for GE refrigerators. It circulates air over the evaporator coils, ensuring consistent cooling throughout the refrigerator and freezer compartments. The motor operates 9.75 volts DC. The motor has a 1/8" shaft and a 12" long, 4-wire harness.
You should replace the evaporator fan motor if it becomes faulty due to wear and tear, electrical issues, or physical damage. Over time, the motor bearings can wear out, or the motor itself can fail due to continuous operation.
Symptoms of a bad evaporator fan motor include:
- The refrigerator or freezer not cooling properly
- Unusual noises coming from the freezer area
- Frost buildup in the freezer
- The refrigerator running continuously without reaching the set temperature
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
Noisy
-
Fridge too warm
-
Freezer section too warm
See more...
Do-It-Yourself Stories from Customers like You
Nothing worked except the light :) Przemyslaw B. • Wallington , NJ • September 20, 2014
I changed the motherboard - computer and also changed the motor in the freezer, because it was doing a howling sound every time it turned on. The repair technician asked for $500 for a repair and that is on top of the $230 I paid him two days before. I looked up the parts and decided to try myself and it paid off. Great instructional videos. Thanks
Read more
More
$85.69
- Compare At:
-
$101.97
- You Save:
-
$16.28
Genuine Ge part
By: Ge
Part Number: WR02X10585
The Door Recess Spring is an OEM replacement part for GE side-by-side refrigerators. It sits within the icemaker door frame to control movement and allow smooth closing/opening of the access point.
Causes of a bad icemaker door recess spring include wear and tear of thin metal coils repeatedly compressing over many years of filling cycles. Exposure to humidity intrusions from melting ice accumulates oxidation shortening spring elasticity.
Symptoms of a bad icemaker door recess spring include:
- Difficulty opening and shutting the icemaker access door securely
- Excessive slamming noise caused by abrupt closing
- Sagging or improper alignment of the door against the frame
- Struggles retaining positioning of the transparent plastic doorway
This genuine GE replacement spring is compatible with Hotpoint, RCA and Kenmore models.
This part fixes the following symptoms
-
Door latch failure
-
Ice maker not making ice
-
Not dispensing water
-
Ice maker won't dispense ice
See more...
Do-It-Yourself Stories from Customers like You
Ice flapper door stopped closing Lawrence D. • Holly Springs , NC • March 21, 2016
My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser...
Read more
More
$7.91
- Compare At:
-
$8.69
- You Save:
-
$0.78
Genuine Ge part
By: Ge
Part Number: WR02X11330
The Refrigerator Union Connector is an OEM replacement part for GE refrigerators. It is responsible for connecting the water supply lines from the kitchen plumbing to the refrigerator, allowing water to flow to the ice maker and water dispenser. The plastic connector assists your water dispenser by joining two 5/16 inch x 5/16 inch plastic water lines. Over time, Union Connectors can crack or break under pressure.
Causes of a bad Union Connector include wear and tear from repeated use, exposure to extreme fluctuations or surges in water pressure, or damage from accidental mishandling.
Symptoms of a bad Refrigerator Union Connector include:
- Water leaks at or near the connector area
- Inconsistent or no water flow to the ice maker/dispenser
- Fluctuations in water pressure to the fridge
- Water damage to surrounding kitchen areas from leaks
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
Leaking
-
Not dispensing water
See more...
Do-It-Yourself Stories from Customers like You
Water leaking from under/behind fridge (two sources) three problems a comedy of errors Joanne R. • Brookfield , WI • November 09, 2015
We noticed a puddle of water in front of the fridge a couple of months ago-dried the floor up both times and thought someone had dropped ice-or spilled water. A couple of weeks ago there was water dripping through the dropped tile ceiling in the basement. I shut off the water for the water supply to the fridge at the copper pipe in the basement and removed some of the tiles which felt a little damp. It still dripped all day. When my spouse came home he pulled down more of the tiles. It was as...
Read more
More
$9.80
- Compare At:
-
$10.78
- You Save:
-
$0.98
Genuine Ge part
By: Ge
Part Number: WR71X10764
The Module Shelf Insert is an OEM part for GE refrigerators. It's designed to enhance the versatility and organization within your fridge by providing an additional layer of storage on existing shelves. This insert allows for the separation of items, making it easier to organize and access your refrigerated goods.
Causes for a Module Shelf Insert to become problematic can stem from overloading it with heavy items, accidental damage from moving items in and out of the fridge, or the natural wear and tear that comes with regular use.
Symptoms of a bad Module Shelf Insert include:
- Difficulty fitting or staying in place on the refrigerator shelf.
- Cracks or damage that compromise its ability to hold items securely.
- Warping that prevents it from sitting flat or properly dividing the shelf space.
This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
Do-It-Yourself Stories from Customers like You
Lots of broken pieces! Nancy H. • Pittsburgh , PA • March 16, 2015
Replaced two drawers, one shelf front, and the grille base
Read more
More
$31.95
- Compare At:
-
$38.34
- You Save:
-
$6.39
Genuine Ge part
By: Ge
Part Number: WR60X10209
The Condenser Fan Motor is an OEM part for GE refrigerators. This fan motor circulates air in the fridge, helping to cool the compressor and condenser coils for better temperature control. It also evaporates extra water in the drain pan, stopping problems from water buildup.
Symptoms of a failing condenser fan motor include:
- The refrigerator running hotter than usual
- Loud noise or rattling sounds coming from the back of the refrigerator
- The refrigerator cycling on and off more frequently or for longer periods
Causes of condenser fan motor failure typically include wear and tear from continuous use, dust and debris accumulation obstructing fan movement, or electrical issues such as faulty wiring or capacitor problems.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Note: This is a (12-volt DC) fan motor. For the (115-volt AC) fan motor, order part number WR60X10220.
Do-It-Yourself Stories from Customers like You
Not cooling properly Carroll D. • Medical Lake , WA • September 25, 2014
New cond fan & new evap fan & new defrost heater unit
Read more
More
$73.95
- Compare At:
-
$88.00
- You Save:
-
$14.05
Genuine Ge part
By: Ge
Part Number: WR23X10783
The Dispenser Switch is an OEM replacement part for GE refrigerators. This switch is crucial for the functionality of the water and ice dispenser, as it activates the dispensing mechanism when the user presses the lever or button. The switch ensures that the refrigerator dispenses water or ice on demand, providing convenience and ease of use.
Over time, the dispenser switch can wear out or become damaged due to frequent use, exposure to moisture, or electrical issues. This can result in the switch failing to activate the dispenser properly, impacting the performance of the refrigerator's dispensing system.
Symptoms of a bad dispenser switch include:
- The water or ice dispenser not responding when the lever or button is pressed
- Intermittent or inconsistent dispensing of water or ice
- The dispenser working only occasionally or requiring excessive pressure to activate
- No audible click or feedback when pressing the dispenser lever or button
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Bad water dispenser micro switch on my ge fridge James G. • Melbourne , FL • November 23, 2014
After disconnecting power to the fridge, I first removed the ice maker/water dispenser/fridge control faceplate. This easily popped out using a flat head screw driver. Then disconnected the 3 wire harness connections to the control board. I next removed the plastic dispenser housing shield. There's only 4 screws that hold this on. Finally, I removed the Micro-switch, disconnected the two wire connectors and installed the replacement switch and reinstalled everything. The repair took only...
Read more
More
$49.95
- Compare At:
-
$59.44
- You Save:
-
$9.49
Genuine Ge part
By: Ge
Part Number: WR24X20455
The Freezer Door Gasket is an OEM part for GE refrigerators. It forms a seal around the freezer door to prevent warm air from entering and cold air from escaping, maintaining the internal temperature and efficiency of the appliance. It measures 24 inches wide by 20 inches high.
Causes of a bad freezer door gasket can include wear and tear over time, cracking or drying out of the rubber material, or damage from repeated use.
Symptoms of a bad freezer door gasket include:
- Frost buildup inside the freezer
- The door not sealing properly
- Increased energy consumption
- Visible cracks or tears in the gasket
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Freezer door gasket lost magnetism. Tim C. • Cumming , GA • August 20, 2017
The freezer door on my 12-yr old GE side-by-side refrigerator/freezer would not stay completely shut resulting in temperature variations and ice buildup from outside humidity seeping into the freezer compartment. These problems were exacerbated by the fact that this appliance is located in my garage in the heat / humidity of the Atlanta, GA area. I applied a thin layer of petroleum jelly to the gasket which improved the seal but did not completely solve the problem. I discovered that...
Read more
More
$73.28
- Compare At:
-
$87.94
- You Save:
-
$14.66
Genuine Ge part
By: Ge
Part Number: WR71X10973
The Door Bin is an OEM part for GE refrigerators. This door bin is designed to fit onto the inner door panel of the refrigerator, providing convenient storage for condiments, bottles, and other items that need to be easily accessible. The use of this bin helps to maximize the storage capacity of the refrigerator, keeping items organized and within reach.
Causes of damage to the door bin often include overloading it with too much weight, which can lead to stress cracks or breakage.
Symptoms of a bad Door Bin include:
- Cracks or breaks in the bin
- The bin not fitting properly onto the door panel
- Difficulty in sliding the bin in and out or removing it for cleaning
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Broken refrigerator shelf Catherine B. • Glastonbury , CT • January 15, 2020
Part came in quickly. Fit right in.
Read more
More
$98.67
- Compare At:
-
$118.40
- You Save:
-
$19.73
Genuine Ge part
By: Ge
Part Number: WR17X10706
The Dispenser Door Recess Crank is an OEM part for GE refrigerators. This crank is a crucial component of the refrigerator's ice and water dispenser system, helping to operate the dispenser door by opening and closing it when activated. It ensures that ice or water is dispensed efficiently and prevents unwanted air from entering the freezer compartment.
You should replace the dispenser door recess crank if it becomes faulty or damaged. Causes of a bad crank can include wear and tear from frequent use, accidental damage, or mechanical failure. A malfunctioning crank can lead to issues with the dispenser door's operation.
Symptoms of a bad dispenser door recess crank include:
- The dispenser door not opening or closing properly
- Ice or water not dispensing correctly
- Unusual noises during the dispensing process
- The dispenser door staying open or not sealing properly
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Ice flapper door stopped closing Lawrence D. • Holly Springs , NC • March 21, 2016
My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser...
Read more
More
$7.37
- Compare At:
-
$8.36
- You Save:
-
$0.99
Genuine Ge part
By: Ge
Part Number: WR17X11497
The Ice Dispenser Crusher Cover is an OEM part for GE refrigerators. This component is crucial for the ice dispensing mechanism, covering the ice crusher blades and ensuring safe and efficient operation when dispensing crushed ice.
Causes of a bad ice dispenser crusher cover can include regular wear and tear, damage from ice buildup, or cracks and breaks due to impact or mishandling. Over time, these issues can compromise the functionality of the ice dispenser, leading to ineffective ice crushing or potential safety hazards.
Symptoms of a bad Ice Dispenser Crusher Cover include:
- Inconsistent ice crushing
- Ice dispenser jams or blockages
- Visible cracks or breaks in the cover
- Unusual noises during ice dispensing
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
Ice maker dispenses too much ice
See more...
Do-It-Yourself Stories from Customers like You
Ice bucket auger fins broke off on gegse22ethc ww side by side frig. Ron N. • Kearney , NE • August 28, 2023
First - I am not a handyman so bear with me. Turned out not only the auger fins were broken off but also the ice dispenser crusher cover had cracks and breaks on it. First - AppliancePartsPros.com has awesome shipping. Because i didn't know right away the crusher cover was broken, I had to do two orders. Each order was received next day in afternoon. Video is great. Tells exactly how to do. There are two issues you will run into. Remembering the exact sequence of all the washers and...
Read more
More
$27.95
- Compare At:
-
$33.54
- You Save:
-
$5.59