Psh25pgw Parts

This base grille mounts across the lower front of the refrigerator, covering and protecting the condenser area and leveling components while guiding airflow. Replacing a damaged or missing grille restores a clean appearance and the intended front-vent path.

• Covers the lower opening and helps keep debris away from condenser components
• Directs airflow through the front vents as designed
• Provides a finished, clean look at the toe-kick
• Helps prevent rattling when secured properly
• Common symptoms: cracked or scuffed grille, broken tabs, won't stay attached, missing piece

• Disconnect power and wear gloves to avoid sharp edges
• Open doors slightly to clear the grille ends
• Remove any screws or release spring clips and retain existing hardware
• Align tabs and snap/secure the new grille; ensure vents remain unobstructed

This is the rear motor cover used in select GE refrigerators. It shields the motor area at the back of the compartment, helping direct airflow and protect the fan/motor assembly for reliable cooling performance.

• Protects the motor/fan area from debris and damage
• Helps channel air correctly through the compartment
• Cracks, broken tabs, or missing cover can lead to noise, poor airflow, frost, or temperature swings
• Restores proper fit and finish inside the compartment

• Unplug the refrigerator before servicing
• Remove shelves/bins obstructing access; retain screws/clips
• Carefully release locking tabs and transfer any reusable hardware
• Ensure the cover seats fully and resecure all fasteners before powering on

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly

This replacement bottom door hinge and pin assembly fits refrigerators. The lower hinge supports the door's weight and provides the pivot point, restoring smooth swing and proper alignment for a reliable close and consistent gasket seal.

• Serves as the door's lower pivot and load-bearing support
• Maintains alignment so the gasket seals correctly
• Restores smooth opening and closing after hinge/pin wear
• Common symptoms: door sagging or dragging, popping/squeaking at the hinge, gaps or poor sealing, door not staying closed

• Disconnect power and remove items from the door before servicing
• Support the door, remove bottom hinge fasteners, and lift the door off
• Position the new hinge and transfer any spacers/shims as found
• Reinstall the door, tighten hardware, and verify alignment and gasket seal

Keep water and ice flowing without internal filtration. This MSWF water filter bypass plug replaces the filter to seal the housing and route water properly to the dispenser and ice maker when a filter is not used.

• Installs in place of the MSWF filter to bypass filtration
• Maintains water flow to the dispenser and ice maker with no filter installed
• Helpful for troubleshooting restricted flow or when using an external filtration system
• Seals the filter head to help prevent leaks during bypass
• Note: No water is filtered while this plug is installed

• Shut off the water supply and dispense water to relieve system pressure
• Remove the MSWF filter; align and twist the bypass plug to lock into the filter head
• Restore water, check for leaks, and run the dispenser briefly to purge air
• Follow your refrigerator's instructions and use appropriate hand/eye protection

This power cord assembly supplies electrical power from the wall outlet to your refrigerator. Replace a cut, frayed, or overheated cord to restore safe, reliable operation and eliminate intermittent power loss caused by a damaged cord. What it does:

• Provides the electrical connection between the household outlet and the refrigerator's wiring
• Helps resolve no-power or intermittent power when the cord is moved
• Addresses visible damage such as cuts, cracks, fraying, or a melted/discolored plug
• Mitigates arcing, sparking, or a burning odor originating from the cord or plug area

• One power cord assembly

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Pull the refrigerator forward for access; note the original cord routing and connections
• Install the new cord along the same path and secure any built-in strain relief; ensure the ground connection is properly seated
• Restore power and verify operation

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

This fan and pre-wired harness assembly drives airflow to the Quick Chill/CustomCool drawer so foods and beverages chill faster and hold the set temperature. Replace a noisy, non-running, or intermittent fan to restore proper drawer cooling.

• Circulates cold air into the Quick Chill/CustomCool/deli drawer for targeted cooling
• Helps correct no-chill or slow-chill performance in the drawer
• Addresses symptoms like no airflow, intermittent operation, or grinding/buzzing noises from the drawer area
• Replaces a failed fan motor or damaged wiring harness in this assembly

• Disconnect power before servicing; remove the drawer and covers to access the assembly
• Note wire routing and connector locations; transfer any original mounting hardware as needed
• Seat connectors fully and route harness away from moving parts to avoid pinching
• Restore power and verify the fan runs and airflow is present to the drawer

Front mounting grommet.

This pan frame assembly forms the shelf and support structure for the refrigerator's Custom Cool/deli drawer. Replacing a cracked or warped frame restores smooth drawer operation and a stable surface for items stored above.

• Supports and guides the Custom Cool/deli drawer for proper opening and closing
• Provides the structural shelf platform above the drawer
• Helps keep the drawer aligned and seated to prevent sticking or falling off tracks
• Common failure signs: cracked frame or tabs, sagging shelf, misaligned or hard-sliding drawer, rattling from a loose frame

• Remove the drawer and any items resting on the frame before starting
• Carefully release locking tabs; avoid over-flexing plastic parts
• Set the new frame evenly on the side supports/rails and ensure all tabs fully engage
• Reinstall the drawer and verify smooth travel and proper door closure before reloading

This screw fastens appliance panels, brackets, and trim so parts stay secure and aligned. Replace a missing, stripped, or rusty screw to stop rattles and restore a tight, factory fit.

• Secures covers, brackets, and trim to the appliance cabinet or liner
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration noise and loose or misaligned parts
• Maintains proper fit of guards, kickplates, or internal panels

• Disconnect power; turn off water supply if working near water lines
• Match to the original fastener to size and thread
• Start threads by hand to avoid cross-threading; tighten snugly, not excessively
• If threading into plastic, avoid overtightening to prevent damage

This white ice dispenser paddle is the lever you press on the freezer door to release ice. Replacing a worn or broken paddle restores reliable ice dispensing and a clean, like-new look at the dispenser.

• Transfers your push to the dispenser switch to start ice delivery
• Helps fix a cracked, broken, loose, or missing paddle
• Addresses a lever that sticks or doesn't return smoothly
• Useful when ice won't dispense unless the switch is pressed directly
• Refreshes a yellowed or scuffed dispenser paddle

• Disconnect power to the refrigerator before servicing
• Remove the drip tray and dispenser trim/control panel to access the paddle
• Note spring/lever orientation and transfer any hardware from the original paddle
• Reassemble, restore power, and test ice dispensing

Size: 10-32 GXTT FLP.595 S

Keep the refrigerator's rear fan assembly secure and airflow on track with this fan orifice bracket. It supports the fan shroud/orifice so the motor and blade stay aligned, helping maintain proper cooling and reduce vibration.

• Secures the fan orifice/shroud to the machine-compartment frame
• Maintains correct fan motor and blade positioning for smooth operation
• Helps direct airflow through the condenser area for effective heat removal
• Typical symptoms of a failed bracket include rattling/buzzing from the back, a loose or wobbling fan assembly, reduced airflow, or warm temperatures

• Disconnect power and move the refrigerator to access the rear machine compartment
• Remove the rear access cover; support the fan motor/blade before loosening fasteners
• Transfer any reusable mounting hardware to the new bracket; align the orifice/shroud properly
• Ensure the fan spins freely and the assembly is secure before reinstalling the rear cover and restoring power

This replacement trim fits the dairy compartment on the refrigerator door. It restores a clean, finished look and proper fit of the butter/dairy bin so contents stay organized and the area opens and closes smoothly.

• Attaches to the front edge of the dairy/butter bin on the fresh food door to provide a finished, secure fit
• Replaces cracked, warped, or missing trim that can cause gaps, rattling, or a loose dairy compartment
• Helps keep small items from sliding out when opening/closing the door
• Built to match the original mounting points for straightforward replacement

• Disconnect power to the refrigerator before servicing
• Open the fresh food door; release tabs or remove any retaining screws to take off the old trim
• Align the new trim with the mounting points and snap in or reinstall existing hardware
• Handle plastic tabs carefully and avoid overtightening screws