Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix washer not spinning or loose cam driver with this wire retaining ring. Secures basket drive components to prevent shifting. DIY-friendly repair.
Based on recommendation to replace the clutch if clothes aren't spinning dry enough, I ordered a new clutch. Upon disassembly, I observed no Ring Wire/C-Clip and that the bearing appeared worn. Where did the clip go? Well, the bearing wore down such that it wore out the clip and bearing up to the sleeve of the shaft. Knocked out the old bearing, tapped in the new and was done. I disassembled the brake shoes but believe you can get the bearing in and out without doing so. Not a bad job, just... Read more
Leaking from the water inlet connection? This vacuum break prevents backflow and maintains the air gap at the inlet. Easy DIY fix in under 30 minutes.
Removed cover from Whirlpool washer (~20 years old) and found water to be leaking from hose connection at Break Vac. Obviously the hose had to be replaced but the Break Vac looked corroded and partially plugged, too, possibly inhibiting water flow. While the cabinet was off I noticed the Suspension Spring was rusted off so I ordered 1 of those, too. Total of all parts was under $45 so looks like we won't be getting a newer, more efficient washer anytime soon. Everything arrived in 3 days and... Read more
Replacement power cord that connects your washer to the wall outlet. Includes strain relief for cable protection. Needed when original cord is damaged, pinched, shorted, or worn. Direct plug-in installation.
Bought a new cord and removed the back of the washer and unclipped the old and clipped in the new. 5 minutes tops. Read more
Secures the door boot seal on front load washers to prevent water leaks. Replace if seal is loose or water seeps during wash cycles. Confirm fit with your model.
Im not a repairman, so all my knowledge to fix my washer came from either youtube or online chats. I posted this to help the next dad trying to save a few bucks. Door sensor... Since door sensor worked correctly, verified that by starting washer with door open, and agitate cycle would not start until door was closed. Meaning door sensor worked correctly. Timer... In high spin cycle washer sounded correcltly spinning, but when opening door, drum was was not moving. So timer was triggering... Read more
Secures the motor to its mounting point in your laundry center. Replace if the retainer is worn, broken, or has lost tension to prevent motor misalignment.
Replaced with new retainer clips and new capacitor to fix future problems Read more
Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.
Followed online video. It was easy Read more
Push-in nut for washers. Secures components and panels inside the cabinet. Replace if cracked, broken, or missing to restore proper assembly.
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair... Read more
Washer won't advance cycles or stops mid-cycle? This timer sequences fill, wash, drain, and spin stages. Moderate DIY repair restores cycle control.
Watched instructional viedeos on how to replace timer. Read more
Secures hose connections to prevent leaks in your washer. Replace if you notice dripping at hose fittings or loose connections. Verify fit with your model.
Took off cover, installed new parts. Read more
Fix a burnt or melted lid switch connector causing your washer to be completely dead. This terminal receptacle restores power to the lid switch.
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!) Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts... Read more
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
Replace your washer's anti-rattle clip to eliminate vibration noise and buzzing during cycles. Secures components with light spring tension. Confirm fit with your model number before ordering.
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever. Read more
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Replaced with new part ordered from store Read more
Secures the rear bulkhead to the washer tub, reducing vibrations. Replace if damaged by water exposure, stripped threads, or rusted from age.
Watched several repair videos on YouTube produced by AppliancePartsPros.com for this model Whirlpool washer (videos quite well done). Purchased parts from AppliancePartsPros.com; order correctly filled and parts arrived by FedEx within two working days. Performed repairs as instructed. "Plastic welded" holes in poly outer tub using similar plastic (PP) using a cheap soldering iron - worked perfectly, saved >$150 for new tub. Washer now like brand new. Suggestion - buy the spanner wrench,... Read more
Two 6-foot braided inlet hoses with 90-degree ends for washer water connections. Replace kinked, aged, or worn hoses to restore proper filling.
I had a problem with the drain pump on my Kenmore HE3 and I replaced it using a drain pump I ordered from APP. That fixed that problem but once I started running the washer I started getting a FH error code. I looked it up and found that it was a problem with the washer not filling properly. I pulled the washer out and found that one of the fill hoses had kinked when I pushed the washer back in place. There was also some writing on the hose that read "Change hose every five years". I know I had... Read more
Two 5-foot nylon braided hoses connect household water supply to washer inlet valves. Replace cracked, leaking, or aging hoses to prevent water damage.
Watched u tube video. Ordered replacement water inlet valve and new hoses. Dismantled washer and replaced defective valve and installed new hoses. The repair went very easily and the washer worked perfectly as a result. Read more