Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement screw that secures the handle to the oven door trim. Needed when original screw is stripped, rusted, lost, or damaged during handle replacement.
Overall the fix wasn't too hard. The challenge was putting the oven door back together and holding it together while trying to tighten the screws. Enlisted my wife's help to hold the door and at first the handle screws wouldn't tighten. My cordless screwdriver's battery was under-charged. Once I switched batteries I was able to tighten the screws. Seemed like I needed to push too hard (my wife freaked "not so hard you will strip them!") however pushing hard was what was needed. Both screws... Read more
Replaces the oven floor panel that sits above the bake element. Needed when warped, cracked, or damaged from spills or foil contact. Restores smooth surface.
The problem is a finicky ignition system, Direct Spark Ignition. Apparently Whirlpool redesigned the igniter/burner assembly slightly to make it more reliable. The repair is very easy. Turn off power, but you don't need to turn off gas. Remove oven bottom and flame spreader, then remove burner/igniter assembly, one screw at front, one at back. Lift out burner assembly carefully to avoid stretching wire. Pull electric connector from pin on burner/igniter assembly. Vacuum to clean oven. ... Read more
Replacement mounting screw for washer drum baffles. Secures baffles to drum interior. Order if original screw is stripped, lost, or corroded during repair.
I replaced all three baffles since the new one was a different design than then old one. i watched the video and the repair went well, except for hitting my hand with a hammer while removing the old baffles. went just like the video said it would Read more
Fix a gas burner that won't light or clicks but doesn't ignite. This range surface burner igniter creates the spark to light your stovetop. 15-30 min repair.
I removed the burners and replaced the igniters. The burners must be removed because the igniters go underneath them. This job turned out to be very difficult because my stove is 16 years old and the screws holding down the igniters were completely rusted and bound to the stove top, so I had to drill out all of the screws. Also, the burners were bound to the gas flues by mineral deposits and separating them was very difficult. Once I got the stove top up, I threaded the igniter wires to the... Read more
Mounting screw for securing trim, hinges, drawer guides, and interior components. Replace if missing, stripped, or broken during repair or maintenance.
The replacement part was identical, arrived quickly as promised, and took only a couple of minutes to install. Excellent service. Very happy with the end result and the whole process. Read more
Replacement oven door handle for ranges. Installs on the front of the oven door. Order when your handle is cracked, broken, or detached. Requires screws.
Replacement 10-32 machine screw for securing panels, brackets, and internal components. Ideal for replacing missing, stripped, or damaged hardware.
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more
8-18 x 1/2 inch mounting screw for securing drawer glides, brackets, and oven door components. Replace missing, stripped, or damaged screws during repairs.
Whenever the drawer was opened, it would fall of the guide rails. This lead to the drawer being crooked several times. I took the drawer out and noticed one of the glides was missing. Ordered a new pair, popped it on and now the drawer slides properly. Read more
Replacement mounting screw for securing range panels, brackets, and internal components. Replace missing, stripped, or rusted screws to restore fit.
Front drawer glide for range broiler or storage drawer. Replace when drawer sags, won't slide smoothly, or glide is broken. Confirm fit with your model.
Replaces broken or worn oven door hinges on ranges. Installs inside the door frame to support proper opening and closing. Sold individually.
This oven was a Kenmore model #66595822003. I replaced both spring hinges. This oven was a white oven so it took the MFG# WP8053807 hinge (order two of them). They are the same hinge. No left or right. To get the door off the oven, open the door all the way open, I installed pins (preferably only 1/4" long) in the holes of both hinges. Then remove the spring steel retainers above old hinges in the oven frame. These holds hinges in place. Now close the door until hinge stops on pins. Lift up... Read more
Fix burners that won't light or click repeatedly. This spark electrode creates the arc to ignite gas at your range burner. Moderate DIY repair.
We replaced the Igniters, Spark Module, Door Seal, and Knobs. Read more
Adjustable front leveling leg threads into the base corner of your range to raise or lower the unit. Replace if broken, cracked, or missing to level your range.
Could not level stove. Front leveling legs had pieces broken out where leg contacted floor. Back leveling legs were worn and did not stay at corrected height when stove returned to full weight on floor. Replaced both front and back leveling legs, and stove was able to be leveled. Also bought Touchup Paint for numerous nicks and scratches - color matched perfectly. Read more
Fix burners that won't light or have lost their spark. This range surface igniter replaces worn igniters on gas stovetop burners. Easy DIY repair.
Secures cooktop panels, burner components, and trim pieces. Replace missing, stripped, or damaged screws to eliminate rattles and keep parts aligned.
After being told by a service repairman that it would cost me close to $200 to repair, I resolved to just not use the dispenser. After about a year, I had decided that I wanted to repair it and would look at the options myself. At the least, I could figure out which parts were needed to repair it and have them on hand for a service guy if I determined I could not do the job myself. The more I studied it, the more I felt confident that I could do it, and sure enough, when the part arrived - a... Read more
If your gas range burner won't light or clicks but doesn't ignite, you may need a new surface igniter. Simple DIY repair with basic tools in 15 minutes.