Wed6000vw0 Parts

This flexible, narrow brush reaches under and behind the cabinet to sweep dust and lint from condenser coils and vents. Cleaning built-up debris helps restore airflow and support proper cooling performance.

• Sweeps dust, lint, and pet hair from condenser coils and ventilation areas
• Flexible reach helps access coils beneath or behind the appliance
• Aids proper heat dissipation by clearing airflow paths
• Helpful when coils are visibly dirty, cooling seems weak, or the unit runs longer than usual

• Unplug or disconnect power before cleaning
• Remove the toe grille or rear access panel if needed to access coils
• Brush gently along the coil fins; avoid bending fins or damaging tubing
• Vacuum or wipe up loosened debris before replacing any panels and restoring power

This air duct collar channels dryer exhaust to the external vent connection. It provides a secure, sealed outlet for the vent hose to help maintain proper airflow, reduce leaks, and support consistent drying performance.

• Directs exhaust air from the blower/outlet to the rear vent connection
• Provides a stable connection point for the vent hose
• Helps maintain airflow and drying efficiency
• Common symptoms: vent hose won't stay attached, heat or lint leakage at the back of the dryer, longer dry times, visible cracks/warping at the outlet

• Disconnect power; for gas dryers, also shut off gas supply
• Pull the dryer forward and detach the vent hose
• Remove mounting screws/clips, replace the collar, and reuse existing hardware
• Clear lint from ducting, reattach the vent hose securely, and verify strong airflow at the exterior vent

This dryer power cord connects an electric dryer to a 4-prong household outlet. Replace a worn or damaged cord to restore a safe, reliable power connection and help prevent intermittent power or overheating at the cord connection. What it does:

• Connects an electric dryer to a 4-prong receptacle for proper power and grounding
• Four-conductor design supports modern installation requirements
• Replaces cords with cracked insulation, loose prongs, or burned terminals

• 1 dryer power cord

• Disconnect power at the breaker before servicing
• Attach to the dryer terminal block per the appliance's wiring diagram and secure the strain relief

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This is a refrigerator door switch. It signals the control when a door is opened or closed to turn interior lights on/off and may pause certain functions. Replacing a faulty switch restores proper lighting and door-activated operation.

• Senses door open/close to control interior lighting
• A failed switch can cause lights to stay on, never come on, or flicker
• May also affect features that depend on door status
• Common signs include no interior light or light remaining on with door closed

• Unplug power before servicing
• Access the switch at the door jamb; gently pry out the old switch
• Transfer and reconnect wiring one terminal at a time to the new switch
• Ensure the switch seats flush and test door operation before closing up

This replacement screw secures appliance panels and components so they stay tight and aligned during use. Replacing a missing or damaged screw restores a solid fit and helps eliminate rattles, loose trim, or shifting parts.

• Fastens brackets, panels, trim, or components to the appliance chassis
• Helps correct loose or missing hardware after vibration or service
• Replaces stripped, rusted, or broken screws
• Can reduce rattling noises or misaligned parts caused by missing fasteners

• Disconnect power; for gas appliances, also shut off the gas supply
• Support the part being fastened; start threads by hand to avoid cross-threading
• Use the correct driver size; tighten snugly without overtightening
• Replace hardware with the exact part number to ensure proper fit

The door switch is an OEM part for Whirlpool dryers. It is the switch component that controls the dryer door function, allowing it to open, close, and latch securely. 

Symptoms of a bad Switch-dor can include: 

• The dryer refusing to start if the door appears closed
• Inability to automatically open the door at the end of a cycle
• Excessive moisture left in clothes 

Causes of failure include general wear and tear over extended use.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

This top panel is the upper cover of your dryer's cabinet. Replace a dented, rusted, or warped panel to restore a secure, flush fit and the clean, finished look of your machine.

• Forms the dryer's upper cabinet surface and covers internal components
• Provides proper mounting/alignment for the control console and top hardware
• Helps maintain cabinet rigidity and a solid, secure fit
• Common signs it's needed: visible dents/bends or rust, top won't sit flush or stay secured, gaps or misalignment near the console

• Disconnect power; shut off gas supply for gas models
• Wear cut-resistant gloves—cabinet edges can be sharp
• Remove fasteners securing the top, lift off, and transfer any clips/insulation from the original panel
• Align the new panel and tighten fasteners evenly to ensure a flush, secure fit

This 6-foot dryer vent duct connects your dryer's exhaust outlet to the wall vent. It provides a secure path for moist air to exit the home, helping maintain airflow and consistent drying performance. What it does:

• Vents hot, moist air from the dryer to the exterior
• Replaces crushed, torn, or lint-clogged ducting
• Helps address longer dry times, heat buildup/shut-offs, or moisture and lint around the dryer
• Supports a short, direct run to reduce kinks and airflow restrictions

• One 6-foot dryer vent duct

• Disconnect power; for gas models, turn off the gas supply before starting
• Pull the dryer forward and remove old ducting and lint/debris from connections
• Attach the duct fully to the dryer outlet and wall vent and secure with clamps; avoid sharp bends or crushing
• Move the dryer back carefully and confirm strong airflow at the exterior vent hood

This top hinge supports the hinged top or upper panel, allowing it to lift for service and close securely. Replacing a worn hinge restores smooth motion and proper alignment to help eliminate wobble, scraping, or gaps.

• Provides the pivot point for lifting the top/panel
• Maintains alignment and helps the top seat flat when closed
• Restores smooth opening/closing without binding or rubbing
• Common signs of failure: loose or uneven top, squeaks, difficulty lifting/closing, visible bending or cracks at the hinge

• Disconnect power; also shut off gas and allow all surfaces to cool
• Support the top/panel while removing and installing the hinge to prevent strain
• Transfer and tighten existing mounting screws unless new hardware is provided
• After installation, check alignment and clearances; replacing hinges in pairs can improve fit

This spring clip secures small panels, brackets, or trim inside your appliance to maintain a snug fit and prevent movement. Replacing a fatigued clip helps restore proper alignment and reduce unwanted vibration or rattling. What it does:

• Provides spring tension to hold a component firmly in place
• Helps prevent vibration, rattling, or shifting during operation
• Replaces a bent, worn, corroded, or missing clip
• Common symptoms: loose or misaligned panel/trim, recurring rattles, or parts that won't stay secured

• 1 spring clip

• Disconnect power (and gas, if applicable) before servicing
• Access the clip location per your model's service/parts diagram
• Note the clip's orientation and attachment points before removal
• Use needle-nose pliers carefully to avoid bending adjacent tabs or brackets

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This lock secures the appliance's top panel to the front frame for a tight, stable cabinet. Replacing a worn lock restores a solid fit and helps eliminate rattles, gaps, and vibration during operation.

• Locks the top panel to the front panel to keep the top closed and secure
• Helps maintain cabinet alignment and rigidity
• Reduces movement that can cause vibration and rattling/squeaking noises
• Common symptoms: loose or popping top, visible gap at front edge, buzzing or clunking during cycles

• Disconnect power before servicing.
• Access the lock at the front edge where the top meets the front panel; remove the old lock and install the new one in the same orientation.
• Reuse original mounting hardware and ensure both sides are evenly aligned.
• Close the top and ensure a secure latch before restoring power.

This Dryer Repair Kit refreshes the tumble system by replacing the high-wear parts that cause noise and poor drum movement. Restore smooth, reliable operation and help extend the life of your dryer. What it does:

• Renews the drive path so the drum turns smoothly and consistently
• Restores proper belt tension and tracking with a new idler pulley
• Replaces worn or noisy drum support rollers to reduce squeaks and thumps
• Helps address symptoms like squealing/squeaking, rumbling/thumping, intermittent or no tumble, and burnt-rubber smells

• Kit includes: drum belt, idler pulley, and drum support rollers

• Disconnect power and shut off gas before servicing
• Access the drum per your model, support it when swapping rollers, and note the original belt routing
• Clean lint and roller shafts; do not lubricate rollers; route the new belt around the motor and idler as designed
• Spin the drum by hand to ensure smooth movement before reassembly and test run

• Replace all drum rollers at the same time to maintain even wear and quiet operation