Wed7ohebwo Parts

The Cover is an OEM part for Whirlpool dryers. This part secures the lint screen in place and ensures that lint, dust, and other debris are effectively captured before they can enter the dryer's vent system.  

Common causes of a bad dryer cover include physical impact, heat-related warping, or degradation over time. A compromised cover can lead to exposure of internal components, potentially affecting the dryer’s performance and safety.

Symptoms of a bad Cover include:

• The lint screen does not stay securely in place.
• Increased lint accumulation within the dryer or vent system.
• The dryer takes longer to dry clothes, indicating airflow issues.
• Visible damage or warping of the cover, which can prevent it from fitting properly.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This sensor wire harness links a sensor (such as a thermistor) to the appliance's control system, ensuring accurate readings and dependable operation. Replacing a damaged or corroded harness restores proper communication and stable performance.

• Carries low-voltage sensor signals between the sensor and main control
• Enables the control to respond correctly to sensor feedback for normal operation
• Typical failure signs: erratic readings, intermittent operation, nuisance sensor/error codes, or visible wire/connector damage
• A damaged harness/connector may be the cause

• Disconnect power before servicing; turn off water supply if moving the appliance requires it
• Access the harness at the sensor/control ends per your model's service information
• Match keyed connectors and seat fully without forcing; do not pull on wires
• Route along the factory path and secure away from sharp, hot, or moving parts

This support washer is a flat spacer used within the mechanism to support and separate mating parts, maintaining alignment and smoother movement. Replacing a worn washer helps reduce friction and wear so components operate properly. What it does:

• Maintains proper spacing and support between adjoining parts
• Helps prevent metal-to-metal contact, reducing scraping or grinding noises
• Addresses wobble or excess play when the original washer is worn, deformed, or missing
• Restores smoother movement and alignment in the assembly

• One support washer

• Disconnect power and water supply before servicing; for gas combos, also shut off gas
• Refer to your model's parts diagram for location and orientation
• Track the order of any shims/spacers during disassembly and reinstall in the same sequence
• Tighten fasteners to manufacturer guidance to avoid deforming the washer or binding parts

This 3/8-16 nut secures appliance components and helps prevent loosening and vibration. Replace a worn, stripped, or missing nut to restore a tight, reliable connection and consistent operation.

• Provides a 3/8-16 threaded fastener connection for applicable bolts or studs
• Helps keep brackets, panels, and other parts firmly in place
• Replaces damaged or missing hardware that can cause looseness or rattling
• Signs of failure include rounded corners, stripped threads, corrosion, or inability to tighten securely

• Disconnect power and, if applicable, shut off water and gas before servicing
• Match thread size to the original part; start threading by hand to avoid cross-threading
• Reinstall any washers/spacers in the original order; tighten securely without over-tightening
• If the original used a locking feature or threadlocker, reinstall per your product's service information

This stationary drying rack sits inside the dryer drum to dry items flat without tumbling. It replaces a missing or damaged rack so you can properly dry sweaters, shoes, and other items that shouldn't rotate in the drum. What it does:

• Provides a stable, non-rotating surface inside the drum for flat-drying
• Allows airflow to dry items that should not tumble (e.g., sweaters or shoes)
• Restores the dryer's rack-dry capability when the original rack is missing or broken
• Typical symptoms: rack is cracked/warped, won't sit securely, or you need to dry items flat

• 1 drying rack

• Unplug the dryer before installing
• Open the door and position the rack so the rear support engages at the back of the drum and the front rests in the door opening
• Ensure the rack is level and secure before loading items evenly
• Do not run standard tumbling cycles with the rack installed; remove it when finished

This snap-action door switch senses whether the door is open or closed. Replacing a worn switch restores proper start/stop control and correct light/fan response tied to door operation, improving safety and reliability.

• Detects door position and signals the control or interrupts power as designed
• Helps prevent operation when the door is open
• Common fix for: won't start, stops when the door shifts, or "door ajar" messages
• Restores proper interior light or fan behavior linked to door status

• Disconnect power before servicing; for high-voltage appliances (e.g., microwaves), discharge capacitors
• Match terminal orientation to the original and transfer wires one at a time
• Install in the original bracket/orientation so the actuator aligns with the latch/striker
• Verify operation with a continuity test before reassembly

This dual heating element fits select electric dryers. It generates the heat required for drying and supports variable heat levels on compatible cycles. Replace a failed element to restore proper temperature and consistent drying performance. What it does:

• Produces heat inside the heater housing; dual-circuit design enables multiple heat outputs on certain cycles
• Typical failure symptoms: no heat, low heat/long dry times, clothes remain damp after a cycle
• A shorted coil can trip safety cutoffs; restricted airflow can contribute to repeat failures

• 1 dual heating element

• Disconnect power before servicing and allow the dryer to cool completely
• Access location varies by model; note wire locations and hardware before removal
• Handle the element carefully to avoid damaging coils; transfer any reusable brackets/hardware from the original part
• Clean the lint path and external venting; correct airflow issues to prevent repeat failures

This hinge retainer plate secures the appliance door hinge to the cabinet or door, keeping alignment and smooth operation. Replace a bent, stripped, or missing plate to stop hinge wobble and help the door close and seal properly.

• Anchors the door hinge and distributes load to prevent shifting
• Maintains proper door alignment and gap for smooth opening/closing
• Helps prevent door sagging, rubbing, or poor gasket sealing
• Typical symptoms include a loose hinge, wobbly door, or door not closing flush

• Disconnect power and support the door before removing any hinge fasteners
• Mark hinge locations to preserve alignment during reassembly
• Install the plate in the correct orientation; transfer any spacers/shims in original order
• Tighten fasteners evenly, then verify door alignment and gasket seal

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

This lint screen grille covers the lint filter opening inside the dryer drum. It supports the lint screen and provides a smooth surface at the opening to prevent snags, restoring proper fit and safe airflow. What it does:

• Supports and aligns the lint screen so it sits flush in the opening
• Shields the blower intake and keeps fabrics from contacting internal parts
• Provides a smooth edge to help prevent clothes from snagging or fraying
• Typical failure signs: cracked or missing grille, broken tabs, lint screen not seating properly, clothes catching near the lint opening

• 1 lint screen grille

• Disconnect power before servicing
• Open the dryer door and remove the screws securing the existing grille
• Lift out the old grille, position the new grille, and secure it with the existing screws
• Reinstall the lint screen and verify it slides smoothly and sits flush

The Door Handle is an OEM part for Whirlpool dryers. It provides a  grip for opening and closing the dryer door, ensuring easy access to the drum.

Over time, the door handle can become worn or damaged due to frequent use, accidental impacts, or general wear and tear. If the handle breaks, it can make it difficult or impossible to open the dryer door.

Symptoms of a bad door handle include:

• The handle becoming loose or wobbly
• Visible cracks or breaks in the handle
• Difficulty in opening or closing the dryer door
• The handle detaching from the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Lint Screen Door is an OEM replacement part for Whirlpool dryers. It is responsible for covering the lint screen area and protecting the inner components of the dryer drum. The lint screen door allows for easy access to clean out lint buildup after each load.

Over time, the door can suffer from wear and tear due to regular handling or accidental impacts. A faulty lint screen door can lead to improper lint trapping, which might cause airflow issues and potential fire hazards.

Symptoms of a bad lint screen door include:

• Difficulty opening or closing the door smoothly
• Gaps or openings that allow lint to bypass the screen
• Warping or misshapen door that no longer fits properly

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This is the washer's main electronic control. As the central control unit, it manages power and communication to key components so cycles start, run, and finish correctly—restoring reliable operation when the original board fails.

• Controls overall cycle timing and option execution
• Distributes power/signals to the water inlet valves, drive motor, drain pump, door lock, and user interface
• Common failure symptoms: won't power on or start, won't advance/complete cycles, unresponsive or intermittent controls

• Disconnect power before service and follow all safety precautions
• Handle the board by the edges and use ESD protection
• Photograph/label wire harnesses; seat all connectors fully and secure routing
• After installation, run the appliance's diagnostic/test cycle to verify operation

10 - 16 x 1/2

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal